First Alert FA148CP manual 56, *57, *58 Menu Modes, System Status Report Codes, Primary Phone No

NOTE: Entry of a number other than one specified will give unpredictable results.

For fields *43 thru *46: Enter 0–9; #+11 for B; #+12 for C; #+13 for D; #+14 for E; #+15 for F. Enter [✱] as the fourth digit if a 3-digit account number (for 3+1 dialer reporting format) is used. Enter 0 as the first digit of a 4-digit account number for Nos. 0000-0999. Exit field by pressing ✱ if only 3 digits are used. E.g., For Acct.

B234, enter:

#+11 2 3 4

✱43 PARTITION 1 PRIMARY ACCT. No.

✱44 PART. 1 SECONDARY ACCT. No.

✱45 PARTITION 2 PRIMARY ACCT. No.

✱46 PARTITION 2 SECONDARY ACCT. No.

✱47 PHONE SYSTEM SELECT

✱48 REPORT FORMAT

✱49 SPLIT/DUAL REPORTING

✱50 BURGLARY DIALER DELAY

✱53 SESCOA/RADIONICS SELECT

✱54 DYNAMIC SIGNALING DELAY

✱55 DYNAMIC SIGNALING PRIORITY

/

	/
	/
	/
		[1]
				[77]
primary			secondary

[0]

[2]

[0]

[0]

[0]

Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *43*. [FFFF] Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *44*. [FFFF] Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *45*. [FFFF] Enter 4 or 10 digits, depending on selection in *48 Report Format. See box above. To clear entries, press *46*. [FFFF]

If Cent. Sta. IS NOT on a WATS line: 0=Pulse; 1=Tone;

if Cent. Sta. IS on a WATS line: 2 = Pulse; 3 = Tone

0	= 3+1, 4+1 ADEMCO L/S STANDARD
1	= 3+1, 4+1 RADIONICS STANDARD
2	= 4+2 ADEMCO L/S STANDARD
3	= 4+2 RADIONICS STANDARD
5	= 10-digit ADEMCO CONTACT ID® REPORTING
6	= 4+2 ADEMCO EXPRESS
7	= 4-digit ADEMCO CONTACT ID® REPORTING
8	= 3+1, 4+1 ADEMCO L/S EXPANDED
9	= 3+1, 4+1 RADIONICS EXPANDED
0	= Standard/backup reporting only (all to primary)
		Primary Phone No.		2nd Phone No.
1	= Alarms, Restore, Cancel				Others
2	= All except Open/Close, Test				Open/Close, Test
3	= Alarms, Restore, Cancel				All
4	= All except Open/Close, Test				All
5	= All				All
0	= no delay		UL: must be “0”
1	= 15 seconds			SIA Installations: delay
2	= 30 seconds			must be minimum of
3	= 45 seconds			30 seconds

0= Radionics (0-9, B-F)

1= SESCOA (0-9 only reporting) Select “0” for all other formats.

Select delay from 0 to 225 secs, in 15-sec increments. 0 = no delay (both signals sent), 1 = 15 secs,

2 = 30 secs, etc.

UL: Grade AA must be “0;” Grade A must be “15” max

0 = Primary Dialer first; 1 = Long Range Radio first. For UL Commercial Burglary installations that use a DACT and LRR, this field must be “0”.

✱56, *57, *58 MENU MODES

These are Menu Mode commands, not data fields, for Zone Programming, Function Key Programming, and Expert Mode Zone Programming respectively. See page 2 and their respective sections in the Installation and Setup Guide for procedures.

TO PROGRAM SYSTEM STATUS, & RESTORE REPORT CODES (✱59 thru *68, *70 thru ✱76, and ✱89):

For 3+1 or 4+1 Standard Format: Enter a code in the first box: 1–9, #+10 for 0, #+11 for B, #+12 for C, #+13 for D, #+14 for E, #+15 for F. A 0 (not #+10) in the first box will disable a report. A 0 (not #+10) in the second box will result in automatic advance to the next field.

For Expanded or 4+2 Format: Enter codes in both boxes (1st and 2nd digits) for 1–9, 0, or B–F, as described above.

A 0 (not #+10) in the second box will eliminate the expanded message for that report. A 0 (not #+10) in both boxes will disable the report.

For Ademco Contact ID® Reporting: Enter any digit (other than 0) in the first box, to enable zone to report (entries in the second boxes are ignored).

A 0 (not #+10) in the first box disables the report.

UL: see installation instructions for requirements

SYSTEM STATUS REPORT CODES (✱59–✱68)

✱59 EXIT ERROR REPORT CODE ✱60 TROUBLE REPORT CODE ✱61 BYPASS REPORT CODE ✱62 AC LOSS REPORT CODE ✱63 LOW BAT REPORT CODE ✱64 TEST REPORT CODE

[0]See box above.

[00]	See box above.
[00]	See box above.
[00]	See box above.
[00]	See box above.
[00]	See box above. Use Scheduling mode to set periodic test reports,

Each mode sets schedule 32 (FA168CPS) or schedule 08 (FA148CP) to the stated

repeat option; first test report sent 12 hours after command.

or use the following key commands:

installer code +[#] + [0] + 0 = test report sent every 24 hours installer code +[#] + [0] + 1 = test report sent once per week installer code +[#] + [0] + 2 = test report sent every 28 days

– 4 –