Kodak 5500, 7500 manual Rear printer, Enabled by your Field Engineer

Page 83

∙ Use the arrow keys to increase or decrease the current distance:

— The left arrow key will decrease the value in 0.125 inch or 1 mm increments.

— The right arrow key will increase the value in 0.125 inch or 1 mm increments.

 

— The down arrow key will decrease the value in 1.250 inch or

 

20 mm increments.

 

— The up arrow key will increase the value in 1.250 inch or 20 mm

 

increments.

 

∙ Press Enter.

Rear printer

NOTE: The rear printer is an accessory which must be installed and

 

enabled by your Field Engineer.

Rear printer defines the options required when using the rear printer accessory.

∙Select Rear Printer from the Mode Configuration window.

Mode Number: 01 Mode Name: MODE01 Item #: 16.0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Mode Configuration

 

 

 

 

 

 

Rear Printer

 

 

Single

Index Format

Patch Reader

Off

 

On/Off

 

Print Definition

6006

IA Field Width

COIN2 Port Select

n/a

 

 

Vertical Start Print Position

3111

Level Rules

OCR

n/a

 

 

 

 

 

 

 

Supprs

IA Display Format

Bar Code Reader

Off

 

Previous Menu

FthenR

Adjoining IA

Printr Controller

Supprs

 

 

 

 

 

 

 

None

Batching

Front Printer

Off

 

 

 

 

 

 

 

 

 

 

 

 

Off

Length Monitor

Rear Printer

Off

 

 

 

 

 

 

Off

Skew Monitor

Mode Name

MODE0

 

 

 

 

 

 

NA NA

Footswitch

Overrides

No Sav

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Save & End Session

Don't Save & End Session

 

 

 

 

 

 

Save & Prev Menu

Don't Save & Prev Menu

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The following pages provide instructions on how to define the rear printer options. When the rear printer definitions are complete, you will automatically be returned to this window.

To close the Rear Printer menu:

∙Select Previous Menu. Proceed to make any additional mode configuration definitions.

NOTE: If the rear printer was not defined as Present during

Accessory Configuration, the following message will appear:

The accessory that you requested is not enabled in

Accessory Configuration.

∙Press Enter to clear the message.

∙Exit from Mode Configuration; refer to the section entitled, Exiting Mode Configuration.

Contact your Field Engineer to install and enable this accessory.

3-62

A-61074 April 1997

Page 82 Page 84
Image 83
Page 82 Page 84
Contents Installation Questionnaire Instructions Mode Setup Software Table of contents Page Minimum system requirements Introduction∙ Press any key to move to the next screen Logon procedureSelect Continue Press Enter. The following screen appears Using the Mode Setup SoftwarePage Scanner configuration items Display language defines the primary display language Default is EnglishDisplay language Options are Default is InchMeasurement system Description 1 Date Format Samples Date format∙ Select the desired time format Time formatTime format defines the time display format Set time and date sets the system clock Default time is 0000 the default date is 10/10/90During configuration to set the system clock Set time and dateField Valid settings Soft Loud ∙ Select the desired confirmation tone volume AprilConfirmation tones Footswitch, patch reader and bar code readerDefault is Enable Enable-indicates that confirmation tones may be usedSpace Fixed field delimiterDash PeriodArea. The input cursor will be positioned at the beginning Number in the document printer print definitions using ModeDefault is blank messages Printer messagesDisplay the curent scanner firmware versions Version numbersFollowing window will appear Load scanner from laptop5500/7500 WindowLoad laptop from scanner Installation or setup change is completedMode Configuration window will appear Mode configurationCopy From Mode Mode to Mode Copy Define Mode Previous Menu To cancel the Mode to Mode Copy Selecting a mode for configuration ∙ Select the desired index format ∙ Press Enter April Mode Index Format∙ Select Index Format from the Mode Configuration window Index formatDescription 1 Index Formats Description 1 Index Formats Proper field definitions ∙ Select IA Field Width from the Mode Configuration windowIA Field width IA Field width defines the image address IA field widthsField a Level Complete listing of the default values for each modeField B Level ∙ Select Field C Field C LevelFixed field contains fixed information, typically the date Fixed fieldDescription 2 Image Address Fields Fixed Field C Field B Field a Level Example Mode Default field widths for each mode are provided belowDocument level is not determined by another method i.e Footswitch, level key, etc∙ Select Level Rules from the Mode Configuration window Level rulesMode Available index formats defined using the Index FormatLevel to follow level Option ∙ Select LevelLevel to follow level Index Format option Two-level two level or two level offset or three-levelThree-level three level or three level offset index formats Defined using the Index Format option ∙ Select LevelLevel April Default level rules for each mode are provided belowLevel Is followed by Mode LevelThree Level Two LevelOffset Control panel Default for all modes is Suppress Leading ZeroesIA Display format Adjoining IA Document scanned in duplex modeDefault for all modes is Front then Rear Batching Length monitor On/off Defines the minimum document length accepted Default for all modes is 2.500 inches / 64 mmMinimum length Defines the maximum document length accepted Default for all modes is 13.000 inches / 330 mmMaximum length Into the Scanner 5500/7500 Error responseDefault for all modes is Display and Beep ∙ Select the desired error response ∙ Press Enter AprilSkew monitor ∙ Select On/Off from the Skew Monitor menu On/off enables or disables skew monitoringDisable-disables all skew monitoring Enable-enables all skew monitoringDetection range defines the amount of tolerable skew Default for all modes is 10-30 degreesDetection range Error response ∙ Select Footswitch from the Mode Configuration window FootswitchPress definition defines the action which is taken when Footswitch is pressedDefault for all modes is No Action Press definitionConfirmation tone Sounds when the Footswitch is pressed or releasedRelease definition defines the action which is taken when Footswitch is releasedRelease definition Patch reader Enabled by your Field Engineer∙ Select On/Off from the Patch Reader menu On/off enables or disables patch readingDisable-disables all patch reading Enable-enables all patch readingTransfer patch definition Sounds when a patch document is detected ∙ Select Disable or Enable OCR COIN2 Port SelectBar code reader ∙ Select On/Off from the Bar Code Reader menu On/off enables or disables bar code readingDisable-disables all bar code reading Enable-enables all bar code reading∙ Select Bar Code Type from the Bar Code Reader menu Default for all modes is Codabar NW-7Bar code type Be read/decoded Default for all modes is One Code DecodedCodes per document Terms of the number of characters encoded Default for all modes isMinimum code length Document option is defined as All Codes Decoded Default for all modes is 1 inch / 25.400 mmMaximum code height Maximum code height defines the maximum bar code height∙ Select the desired scan direction ∙ Press Enter April Scan directionTime required to read/decode bar codes is extended Read/decoded Default for all modes is Normal QualityCode quality Sounds when the bar code reader detects a bar code document Bar code location To close the Printer Controller menu Printer controller∙ Select IA Print Format from the Printer Controller menu IA Print formatFront printer and/or the rear printer Printer and/or the rear printer Default for all modes is SmallFont size Following illustrate the appearance of each orientation Default for all modes is CineCharacter orientation And/or the rear printerFront printer ∙ Select On/Off from the Front Printer menu On/off enables or disables printing by the front printerDisable-disables printing by the front printer Enable-enables printing by the front printerPer Level option Print definitionTotal Doc Counter F09 Vertical start print position Rear printer ∙ Select On/Off from the Rear Printer menu On/off enables or disables printing by the rear printerDisable-disables printing by the rear printer Enable-enables printing by the rear printerAre listed in the window Further described on the following pagesAssigned to the document. You may elect to print the same Mode Number Items box ∙ Enter the desired mode name ∙ Press Enter April Mode nameMode name defines a name for the mode Default is Mode xx, where xx is the 2-digit mode number∙ Select the desired override option ∙ Press Enter April Overrides enable or disable mode overridesOverrides Exiting the mode configuration menu Appendix a Default summaries Default Values Description Mode Mode configuration defaultsDefault Values Mode OCR Mode configuration defaults Appendix B Language support Code Abcæe Blank Business I M AG I N G Systems
Related manuals
Manual 120 pages 51.95 Kb

5500, 7500 specifications

The Kodak 5500 and 7500 series scanners are advanced imaging devices designed for high-quality archival, document, and photo scanning. These models represent the evolution of Kodak’s commitment to delivering reliable and efficient scanning solutions for both professional and personal use, catering to a wide range of needs from archival preservation to day-to-day document handling.

Starting with the Kodak 5500, this model features a robust design and a remarkable scanning resolution of up to 600 dpi, which ensures that images are captured with exceptional clarity and detail. The 5500 is equipped with dual-side scanning capabilities, allowing users to complete tasks faster by scanning both sides of an item simultaneously. This is particularly beneficial for organizations looking to digitize large volumes of documents efficiently.

On the other hand, the Kodak 7500 takes scanning technology a step further. It includes advanced image processing features such as automatic color detection, intelligent background removal, and image enhancement capabilities, which help to improve the quality of scanned documents. With a native resolution of up to 600 dpi, the 7500 excels in capturing high-fidelity images, making it ideal for photographers and professionals working with delicate materials.

Both models incorporate Kodak's state-of-the-art imaging technologies, including Perfect Page technology, which optimizes the scan quality across various types of documents. This technology adjusts for brightness, contrast, and color for each scanned item, ensuring consistent and professional results regardless of the original document's condition.

Another noteworthy characteristic is their user-friendly interfaces, designed to simplify the scanning process. Features such as touch-screen controls and quick-set buttons allow users to initiate scans effortlessly. The scanners also support various connectivity options, including USB and network scanning, enabling seamless integration into existing workflows.

In terms of performance, the Kodak 5500 and 7500 boast impressive scan speeds, making them efficient tools for any scanning project. Users can expect to handle stacks of documents or multiple images without compromising on speed or quality.

Overall, the Kodak 5500 and 7500 series stands out in the market for their exceptional features, reliable performance, and innovative technologies, making them suitable choices for anyone needing high-quality scanning solutions.
Top Page Image Contents