DSCover Satellite Products PC1555MX Trouble Display, Alarm Memory, Door Chime On/Off

Page 13

K e y p a d C o m m a n d s : 3 . 4 [ * ] C o m m a n d s

[*][2] Trouble Display

The panel constantly monitors itself for several different trou- ble conditions. If a trouble condition is present, the Trouble light will be on and the keypad will beep twice every 10 sec- onds. The trouble beep can be silenced by pressing any key on any keypad. If Bell Squawk on Trouble is enabled (sec- tion [014], option [5]), the bell will squawk every 10 seconds when a trouble condition is present.

To view trouble conditions from an LED keypad:

1.Press [*][2].

2.The keypad will flash the Trouble light. The zone indicator lights corresponding to the present trouble conditions will be ON.

When using an LCD keypad, the trouble conditions will be listed on the display. Use the arrow (< >) keys to scroll through the list of present trouble conditions.

NOTE: Troubles can be viewed while armed using the LCD keypad, provided the keypad is version 2.0 or later. Older key- pads will incorrectly display “Fire Trouble”. If using older LCD keypads, programming section [013], option [3] as OFF will ensure troubles are displayed correctly.

The various troubles are described below:

Light

Trouble

 

 

 

 

 

1

Service Required: Press [1] to determine the specific trouble. Lights 1 - 8 will light up to indicate the trouble:

 

•

Light [1]

Low Battery: Main panel backup battery charge is low (below 11.5 volts under load).Trouble is restored

 

 

 

when the battery charges over 12.5 volts.

 

•

Light [2]

Bell Circuit Trouble: The bell circuit is open (see section 5.13 “Bell” on page 22).

 

•

Light [3]

General System Trouble: The PC5204 Power Supply module has an AUX failure, PC5204 Output #1 Trouble,

 

 

 

Home Automation Trouble, or a printer connected to the PC5400 Printer module has a fault and is off-line.

 

•

Light [4]

General System Tamper: Tamper has been detected in a module.

 

•

Light [5]

General System Supervisory: The panel has lost communication with a module connected to the Keybus

 

 

 

(see section 2.7 “Supervision” on page 5). The event buffer will log the event.

 

NOTE: All tamper conditions must be physically restored before the trouble condition will clear.

 

•

Light [6] – Not used

 

 

•

Light [7]

PC5204 Low Battery: The PC5204 module has a low backup battery.

 

•

Light [8]

PC5204 AC Failure: The PC5204 module has lost AC power.

 

NOTE: If you remove and then restore power to the main panel in order to service any PC5204 module, or any module

 

being powered by a PC5204, you must also remove and then restore power to the PC5204 and any connected modules.

 

This ensures that any troubles present on the module are correctly logged and/or annunciated.

 

 

2

AC Failure: AC power is no longer being supplied to the control panel. The Trouble light will flash if an AC Failure is

 

present, if the Trouble Light Flashes if AC Fails option is programmed (section [016], option [2]). This trouble will not be

 

displayed if the AC Trouble Displayed option is disabled (section [016], option [1]). See section 5.8 “Communicator –

 

Reporting Codes” on page 17 for information on AC trouble reporting.

 

 

3

Telephone Line Monitoring Trouble (TLM): There is a problem with the telephone line (See section 5.12 “Tele-

 

phone Line Monitor (TLM)” on page 22.)

 

 

4

Failure to Communicate (FTC): The communicator failed to communicate with any of the programmed telephone

 

numbers (see section 5.5 “Communicator – Dialing” on page 17).

 

 

5

Zone Fault (including Fire Zone): A zone on the system is experiencing trouble, meaning that a zone could not

 

provide an alarm to the panel if required to do so (e.g. a fire zone is open, or there is a short on a DEOL zone, or a super-

 

visory fault on a wireless zone). When a zone fault trouble condition occurs, the keypad(s) on the system will start to

 

beep. Press [5] while in Trouble mode to view the affected zones.

 

NOTE: A Fire zone trouble will be generated and displayed in the armed state.

 

 

6

Zone Tamper: A zone configured for Double End Of Line resistor supervision has a tamper condition, or the tamper

 

switch is open on a wireless device. When a tamper condition occurs, the keypad(s) will start to beep. Press [6] while in the

 

Trouble mode to view the affected zones. If a zone is tampered or faulted, it must be fully restored to clear the trouble.

 

NOTE: By enabling Tampers/Faults Do Not Show as Open in section [013], option [4], Faults and Tampers will not show

 

as open on the keypad, and will be hidden from the end user. If the option is disabled, Faults and Tampers will be dis-

 

played on the keypad

 

 

NOTE: Once a zone is tampered or faulted, it must be completely restored before the trouble condition will clear.

 

 

7

Device Low Battery: A wireless device has a low battery condition. Press [7] one, two, or three times to view which

 

devices are experiencing battery failure. An LED keypad will indicate battery failure using zone lights 1 to 8. The follow-

 

ing will occur:

 

 

 

 

 

Keypad beeps: Keypad displays:

 

Press [7]

 

1

Zones with low batteries (LED keypad - zone lights 1 to 32)

 

Press [7] again

2

Handheld keypads with low batteries (LED keypad - zone lights 1 to 4)

 

Press [7] again

3

Wireless keys with low batteries (LED keypad - zone lights 1 to 8)

 

 

 

To view the battery conditions of wireless keys 9 through 16, you must use an LCD keypad.

 

 

8

Loss of System Time: When the panel is powered up, the internal clock needs to be set to the correct time. This

 

trouble is cleared when an attempt is made to reset the clock.

[*][3] Alarm Memory

The Memory light will be on if any alarm occurred during the last armed period or – in the case of 24 hour zones – if an alarm occurred while the panel was disarmed.

To view alarm memory, press [*][3]. The keypad will flash the Memory light and the zone indicator lights corresponding to

the alarm or tamper conditions which occurred during or since the last armed period. To clear the Memory light, arm and dis- arm the system.

[*][4] Door Chime On/Off

The door chime feature is used to sound a tone from the key- pad whenever a zone programmed as a chime zone is acti-

WWW.DIYALARMFORUM.COM

9

Page 12 Page 14
Image 13
Page 12 Page 14
Contents See Back Cover for New Features Installation ManualLimited Warranty Table of Contents PC1555MX Wiring Diagram System Introduction SpecificationsOut of the Box Additional DevicesGetting Started Installation StepsTerminal Descriptions Keybus Operation & Wiring Wire Routing for Power & Non-Power LimitedExample of Keybus Wiring Zone Input Terminals Z1 to Z6Zone Wiring Current Ratings Modules & AccessoriesKeypad Assignment Supervision11 24-Hr Auxiliary Input Wiring PGM2 Fire Zone WiringLinks Zone Wiring Links Supervision 24 Hour Supervisory Keypad ZonesLinks Answer Assigning Keypad ZonesCommands Keypad CommandsArming and Disarming Auto Bypass Stay ArmingTrouble Display Alarm MemoryTo view trouble conditions from an LED keypad Door Chime On/OffSupervisor Codes Access Code 41 Master Code Access CodeAccess Code Attributes Viewing the Event Buffer from an LCD KeypadFunction Keys Features Available for the LCD5500Z Installer’s Programming How to ProgramProgramming Decimal Data Programming HEX DataPage Programming Security Codes Program DescriptionsZone Programming Zone Attributes Assigning Keypad Zones Communicator Account NumbersCommunicator Dialing Communicator Telephone NumbersAC Failure Trouble Alarm Code Openings/Closings by Wireless KeyZone Restorals Closings Arming CodesContact ID Pulse FormatsAdditional Notes on Contact ID Pager FormatPGM Output Options DownloadingTLM and Alarm Keypad Buzzer Follower ModeArmed Status Ready To ArmBell Telephone Line Monitor TLMTest Transmission Transmission DelayFire, Auxiliary and Panic Keys Arming/Disarming OptionsSwinger Shutdown Entry/Exit Delay OptionsEvent Buffer Keypad Lockout OptionsKeypad Backlighting Keypad BlankingLoop Response Keypad TampersInstaller’s Lockout Resetting Factory DefaultsWalk Test Installer Additional System ModulesFor the Record Programming WorksheetsModule Name Description Location Keypads Keypad Type LocationZone Programming Summary Serial Number WirelessSystem Zone Label Zone Attributes Type Keypad Programming DefaultBasic Programming Function Key OptionsProgrammable Output Options System Times Default Valid entriesSecond System Option Code Default Off Section First System Option Code Default Off Section Page #Program PGM Option Attributes in sections 143 Program PGM Option Attributes in sections 151Fourth System Option Code Default Off Section Page # Third System Option Code Default Off Section Page #Fifth System Option Code Default Off Section Page # Zone Loop Response Options Default Off Section Page #Advanced System Programming Zone Attribute Defaults Y = Option on N = Option OFFZone Type Section Zone # TypePGM Option PGM Attribute Defaults Y = Attribute on N = Attribute OFFPC5208 Main BoardPC5204 Communicator Programming Miscellaneous Closing Arming Reporting Codes Miscellaneous Opening Disarming Reporting Codes Default Option01 20 BPS, 1400 HZ handshake 02 20 BPS, 2300 HZ handshake PagerFirst Communicator Option Code Default Communication Variables Default SectionDefault Ffff Second Communicator Option Code DefaultDefault Ffffff I I I I I Default Option OffInternational Programming Special Installer FunctionsModule Programming SIA Format Level 2 Hardcoded Appendix a Reporting CodesSIA Format Automatic Zone Alarm/Restoral Codes Contact ID Zone Alarm/Restoral Event Codes as per AdemcoAppendix B Programming LCD Keypads Third User Display Mask Default Option Second User Display Mask Default OptionKey Options Default Fourth User Display Mask Default OptionFifth User Display Mask Default Option UL Listed Commercial and Residential InstallationsSixth User Display Mask Default Option Reset LCD Eeprom to Factory Defaults Ascii CharactersImportant Information Changes for PC1555MX PC1555MX Module Compatibility

PC1555MX specifications

The DSCover Satellite Products PC1555MX is an advanced satellite communication device designed to meet the demands of both commercial and industrial sectors. Its high-performance capabilities are complemented by a robust design, making it an excellent choice for users who require reliable connectivity in remote or challenging environments.

At the heart of the PC1555MX is its cutting-edge satellite technology, which enables seamless communication regardless of geographical constraints. The device operates on multiple frequency bands, enhancing its versatility and ensuring optimal performance in diverse conditions. This multi-band capability allows for greater flexibility in communication, accommodating various applications from data transmission to voice calls.

One of the standout features of the PC1555MX is its impressive data transfer speeds. With advancements in modulation techniques, users can enjoy fast and efficient data upload and download rates. This makes the device particularly suitable for applications that require real-time data processing, such as telemetry, remote monitoring, and emergency response communications.

The PC1555MX also incorporates advanced encryption protocols to ensure data security during transmission. This is especially crucial for industries such as defense, security, and finance, where sensitive information must be safeguarded against potential breaches. Users can have peace of mind knowing that their communications are protected by state-of-the-art security measures.

In addition to its communication capabilities, the PC1555MX is designed with user-friendly operation in mind. Its intuitive interface allows for easy navigation and control, making it accessible even to those with limited technical expertise. Furthermore, the device is equipped with a comprehensive alert system that notifies users of any connectivity issues or performance deviations, ensuring that they remain informed and can take swift action if necessary.

Durability is another key characteristic of the DSCover PC1555MX. Built to withstand harsh environmental conditions, it features a rugged exterior that is both weather-resistant and shockproof. This level of durability makes the device suitable for deployment in various settings, from outdoor expeditions to industrial sites.

Overall, the DSCover Satellite Products PC1555MX stands out as a premier choice for satellite communication. With its advanced features, robust design, and commitment to security and performance, it effectively meets the needs of users in an increasingly connected world. Whether for business operations or emergency services, the PC1555MX ensures that critical communications remain uninterrupted.
Top Page Image Contents