Kenmore 153.333315 HA, 153.333345, 153.333545 Facts to Consider About Location, Fire Hazard

Page 9

Facts to Consider About

the Location

Carefully choose an indoor location for the new water heater, because the placement is a very important consideration for the safety of the occupants in the building and for the most economical use of the appliance. This water heater is not for use in manufactured (mobile) homes or outdoor installation.

Whether replacing an old water heater or putting the water heater in a new location, the following critical points must be observed:

Select a location indoors as close as practical to the gas vent or chimney to which the water heater vent is going to be connected, and as centralized with the water piping system as possible.

Selected location must provide adequate clearances for servicing and proper operation of the water heater.

Property Damage Hazard

Allwater heaterseventuallyleak

Do notinstallwithout adequatedrainage

Installation of the water heater must be accomplished in such a manner that if the tank or any connections should leak, the flow will not cause damage to the structure. For this reason, it is not advisable to install the water heater in an attic or upper floor. When such locations cannot be avoided, a suitable drain pan should be installed under the water heater. Drain pans are available at your local Sears or hardware store. Such a drain pan must have a minimum length and width of at least 2 inches (51 ram) greater that the water heater dimensions and must be piped to an adequate drain. The pan must not restrict combustion air flow.

Fire or Explosion Hazard

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other app}}ance

Avoid all ignition sources if you smell LP gas.

Do not expose water heater control to excessive gas pressure

Use only gas shown on rating plate.

Maintain required clearances to combustibles

Keep ignition sources away from faucets after

.. extended period of non use.

installing, using or serv)cing

Read instruction manual before

water heater.

i

INSTALLATIONS IN AREAS WHERE FLAMMABLE LIQUIDS

(VAPORS) ARE LIKELY TO BE PRESENT OR STORED

(GARAGES, STORAGE AND UTILITY AREAS, ETC.): Flammable liquids (such as gasoline, solvents, propane [LP or butane, etc.] and other substances such as adhesives, etc.) emit flammable vapors which can be ignited by a gas water

heater's pilot light or main burner. The resulting flashback and fire can cause death or serious burns to anyone in the area. Even though this water heater is a flammable vapors ignition resistant water heater and is designed to reduce the chances

of flammable vapors being ignited, gasoline and other flammable substances should never be stored or used in the same vicinity or area containing a gas water heater or other open flame or spark producing appliance.

Also, the water heater must be located and/or protected so it is not subject to physical damage by a moving vehicle.

 

 

For continued protection against

 

 

risk of

fire:

 

 

• Do not instalJ water heater on

I

_

carpeted floor

 

Fire Hazard

 

 

• Do not operate water heater if

 

i

flood

damaged.

This water heater must not be installed directly on carpeting. Carpeting must be protected by metal or wood panel beneath the appliance extending beyond the full width and depth of the appliance by at least 3 inches (76.2mm) in any direction, or if the appliance is installed in an alcove or closet, the entire floor must be covered by the panel. Failure to heed this warning may result in a fire hazard.

Fire or Explosion Hazard

using or servicing water heater.

Improper use may result in fire or explosion

Maintain required clearances to corn bustiblee.

Minimum clearances between the water heater and combustible

construction are 0 inch at the sides and rear, 4 inches (102 ram) at the front, and 6 inches (153 ram) from the vent pipe, see Figure 8. Clearance from the top of the jacket is 12 inches (305 mm) on most models. Note that a lesser dimension may be allowed on some models, refer to the label attached adjacent to the gas control valve on the water heaten

TOP ViEW

 

TOP VIEW

 

OF CLOSET

 

OF CLOSET

 

WITHOUT DOOR

 

WITH DOOR

 

_11

o''MIN

O" MIN.

0"

MIN,

_(_414

rnm)

4"

MIN,

0" IV]IN,

FIGURES.

9

Image 9
Contents Installation Safety InstructionCare Maintenance Troubleshooting Parts List Installation and service must beImportant Definitions Riskoffire Improper installation and use may result Property damageExplosion Hazard Feel water before bathing or showeringLighting Operating Label Temperature Regulation Water Piping 12-13 TemperatureTank Sediment Cleaning Venting System Inspection Matedal Needed BasicDimensions RecoveryTank Type Ventpipe DiameterAdditional Tools Needed When Sweat Soldering Materials NeededBasic Tools Thermostat ALL Piping Materialsto be Suppliedby CustomersPilot & Main Burner Removing the Old Water Heater FURE2FKURE5 Fire Hazard Facts to Consider About LocationDoor FURE9 Insulation BlanketsALL AIR from Outdoors See Figures 9, 11,12 ALL AIR from Inside BuildingsProperty Damage Hazard Water PipingTemperature-Pressure Relief Valve Installation Completed UsingWater Damage Hazard Venting Filling the Water HeaterProperty Damage Hazard Breathing Hazard Carbon Monoxide GasFire and Explosion Hazard Gas PipingFire and Explosion Hazard Sediment TrapsGAS Piping with ALL Black Iron Pipeto GAS Control GAS Control For Your Safety Read Before LightingTemperature Regulation Burner Cleaning Tank Sediment Cleaning Burner InspectionVent System Inspection Carbon Monoxide and Fire HazardHousekeeping Temperature-Pressure Relief Valve OperationAnode Rod Inspection DrainingDrain Valve Washer Replacement ServiceSee Figure Expansion Tank Sizing Chart Thermal Expansion Tank SpecificationsStart Up Conditions Strange SoundsCondensation High Temperature Shut Off SystemSmoke Odor AIR In Hot Water FaucetsFURE27 Operational Conditions Leakage CheckpointsStay LIT Pilot Outage Model Numbers Key No. Part Description Burner AssemblyFull ONE Year Warranty on Water Heater Limited Warranty on Tanks That LeakSears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A

153.333315 HA, 153.333445, 153.333415 HA, 153.333545, 153.333345 specifications

The Kenmore 153.333345, 153.333545, 153.333445, 153.333315 HA, and 153.333415 HA air conditioning units represent a diversified range of solutions for both residential and commercial climate control needs. These models are specifically designed to meet the varying requirements of different environments, making them excellent choices for effectively managing indoor temperatures.

One of the main features of these Kenmore models is their advanced energy efficiency. Each unit is equipped with Energy Star certification, ensuring that they consume less electricity compared to standard models. This not only helps consumers save on energy bills but also contributes to environmental sustainability by reducing greenhouse gas emissions.

The cooling capacity of these units is tailored to fit spaces of various sizes. With BTU ratings that range across the different models, users can find an appropriate solution whether they require cooling for a small room or a more expansive area. Additionally, the inclusion of variable speed compressors allows for precise temperature control and improved humidity management, providing enhanced comfort without excessive energy expenditure.

Technologically, these models incorporate modern smart features that make user interaction seamless. Many of the Kenmore units can be controlled via smartphone apps and are compatible with smart home systems. This connectivity allows users to adjust settings, set schedules, and even monitor energy usage remotely.

The design of the Kenmore air conditioners emphasizes ease of installation and maintenance. Their lightweight construction permits simpler setups, while detachable filters ensure that air quality remains high by allowing for easy cleaning and replacement. Moreover, the units feature robust build quality, designed to withstand the rigors of daily use over many years.

In terms of noise levels, Kenmore has prioritized quiet operation. These air conditioners are engineered to operate at lower decibel levels, meaning that they can be used in bedrooms or quiet office spaces without causing disturbances.

In summary, the Kenmore 153.333345, 153.333545, 153.333445, 153.333315 HA, and 153.333415 HA air conditioning units present a blend of energy efficiency, advanced technology, ease of use, and reliability. These features make them excellent choices for anyone looking to optimize indoor comfort while minimizing energy impact.