Kenmore 153.326162, 153.326265, 153.326264 Temperature-Pressure Relief Valve Optional Location

Page 11

is made with any live electrical part. The discharge opening must not be blocked or reduced in size under any circumstances. Excessive length, over 30 feet (9.14 m), or use of more than four elbows can cause restriction and reduce the discharge capacity of the valve.

No valve or other obstruction is to be placed between the relief valve and the tank. Do not connect tubing directly to discharge drain unless a 6 inch air gap is provided. To prevent bodily injury, hazard to life, or property damage, the relief valve must be allowed to discharge water in quantities should circumstances demand. If the discharge pipe is not connected to a drain or other suitable means, the water flow may cause property damage.

The Discharge Pipe:

•Shall not be smaller in size than the outlet pipe size of the valve, or have any reducing couplings or other restrictions.

•Shall not be plugged or blocked.

•Shall be of material listed for hot water distribution.

•Shall be installed so as to allow complete drainage of both the temperature-pressure relief valve, and the discharge pipe.

•Shall terminate at an adequate drain.

•Shall not have any valve between the relief valve and tank.

The temperature-pressure relief valve must be manually operated at least once a year. Caution should be taken to ensure that (1) no one is in front of or around the outlet of the temperature-pressure relief valve discharge line, and (2) the water manually discharged will not cause any bodily injury or property damage because the water may be extremely hot.

If after manually operating the valve, it fails to completely reset and continues to release water, immediately close the cold water inlet to the water heater, follow the draining instructions, and replace the temperature-pressure relief valve with a new one.

FIGURE 10.

Temperature-Pressure Relief Valve - Optional Location

An optional temperature-pressure relief valve location is provided on the jacket top.

If the top location is preferred, the temperature-pressure relief valve in the side location and the counter-sunk plug in the top location can be interchanged.

Be sure to use new pipe joint compound or put two to three turns of teflon tape around the threaded ends of the temperature- pressure relief valve and counter-sunk plug when reinstalling these parts.

FIGURE 10A.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Power Miser Electric Water HeaterSafe INSTALLATION, USE and Service General Safety Table of Contents Introduction Product SpecificationsBasic Tools Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Materials NeededRemoving the Old Water Heater Installation InstructionsFacts to Consider About Convertible Lower Element Facts to Consider About the LocationInsulation Blankets Water Piping Valve and Pipe Insulation Temperature-Pressure Relief ValveTemperature-Pressure Relief Valve Optional Location Converting the Lower Element Filling the Water HeaterPage Wiring Page Wiring Diagrams Upper and Lower Thermostat Adjustments Service and AdjustmentTemperature Regulation Temperature SettingsDraining Temperature-Pressure Relief Valve OperationAnode Rod Inspection Element Cleaning/Replacement Thermostat Removal/ReplacementPage Page Service Drain Valve Washer ReplacementOperational Conditions TroubleshootingStart Up Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Model NO’S Repair Parts ListMY-HOME

153.326162, 153.326265, 153.326264, 153.326163 specifications

Kenmore has long been recognized for its reliable and innovative home appliances, and its models 153.326264, 153.326265, 153.326162, and 153.326163 are no exception. These kitchen appliances, primarily focusing on mixers and food processors, combine advanced technology with user-friendly features to help streamline meal preparation.

The Kenmore 153.326264 is designed for those who appreciate versatility in cooking. Equipped with multiple mixing speeds, this model allows users to customize their mixing intensity depending on the task. From whipping delicate cream to kneading dough, the easy-to-use control interface provides precise adjustments. Its robust motor ensures efficient processing, reducing prep time significantly.

In contrast, the Kenmore 153.326265 focuses on food processing capabilities. This appliance boasts a powerful motor that can handle a variety of ingredients, from tough vegetables to hard cheeses. Its sharp blades and large capacity bowl make it an ideal choice for meal preps that require chopping, slicing, or grating. Additionally, the model features multiple attachments, including a dough blade and slicing disc, enhancing its functionality.

The Kenmore 153.326162 emphasizes compact design without sacrificing performance. This mixer is perfect for smaller kitchens yet offers a powerful motor that can tackle all mixing tasks. Its lightweight construction allows for easy handling and storage, while its sleek aesthetics can seamlessly blend into modern kitchen decor.

Lastly, the Kenmore 153.326163 integrates smart technology with traditional mixing capabilities. This model is equipped with a digital interface that includes preset mixing programs for various recipes. Users can simply select their desired program, and the appliance will automatically adjust speed and timing for optimal results. This feature is particularly beneficial for novice cooks who may be unsure of the right settings for different tasks.

Across these four models, Kenmore emphasizes durability, ease of use, and efficiency, catering to a wide range of culinary enthusiasts. With their combination of powerful motors, thoughtful design, and innovative features, these kitchen appliances are designed to make cooking enjoyable and hassle-free. Whether you're an avid home chef or simply looking to simplify your meal prep, these Kenmore models provide the tools needed to bring your culinary creations to life.
Top Page Image Contents