Kenmore 153.326162, 153.326265 Thermostat Removal/Replacement, Element Cleaning/Replacement

Page 19

The water heater should be drained if being shut down during freezing temperatures. Also, periodic draining and cleaning of sediment from the tank may be necessary.

1.Before beginning turn “OFF” the electric power supply to the water heater.

2.CLOSE the cold water inlet valve to the water heater.

3.OPEN a nearby hot water faucet and leave open to allow for draining.

4.Connect a hose to the drain valve and terminate to an adequate drain or outdoors.

5.OPEN the water heater drain valve to allow for tank draining.

NOTE: If the water heater is going to be shut down and drained for an extended period, the drain valve should be left open with hose connected allowing water to terminate to an adequate drain.

6.Close the drain valve.

7.Follow “Filling the Water Heater” instructions in the “Installation Instructions” section.

8.Turn “ON” power to the water heater.

Never use this water heater unless it is completely full of water. To prevent damage to the tank and heating element, the tank must be filled with water. Water must flow from the hot water faucet before turning “ON” power.

Thermostat Removal/Replacement

1.Turn “OFF” the electrical power to the water heater at the junction box.

2.Remove the access panel and the insulation cap with handle.

3.Lift out the tab as shown below to unclip the terminal cover from the thermostat. The terminal cover can now be removed from the thermostat.

FIGURE 29.

4.Disconnect wires from thermostat.

5.Remove the thermostat from behind the thermostat bracket.

6.Place the new thermostat in the bracket making sure it fits firmly against the tank.

7.Attach the wires to the new thermostat.

NOTE: Some of the terminals may require straight-in wiring through an eye-opening. If wires are now looped, recut and strip wire 3/8” to a straight length and insert.

8.Put plastic terminal cover back in place.

9.Replace the insulation cap with handle to cover the thermostat.

10.Replace access panel, then turn the electric power on.

Element Cleaning/Replacement

NOTE: These instructions are written for element cleaning and element replacement for the lower element. If it is necessary to clean or replace the upper element, then repeat these instructions.

To remove the element from your tank in order to clean or replace it:

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Power Miser Electric Water HeaterSafe INSTALLATION, USE and Service General Safety Table of Contents Introduction Product SpecificationsBasic Tools Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Materials NeededRemoving the Old Water Heater Installation InstructionsInsulation Blankets Facts to Consider About the LocationFacts to Consider About Convertible Lower Element Water Piping Valve and Pipe Insulation Temperature-Pressure Relief ValveTemperature-Pressure Relief Valve Optional Location Converting the Lower Element Filling the Water HeaterPage Wiring Page Wiring Diagrams Upper and Lower Thermostat Adjustments Service and AdjustmentTemperature Regulation Temperature SettingsAnode Rod Inspection Temperature-Pressure Relief Valve OperationDraining Element Cleaning/Replacement Thermostat Removal/ReplacementPage Page Service Drain Valve Washer ReplacementStart Up Conditions TroubleshootingOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Model NO’S Repair Parts ListMY-HOME

153.326162, 153.326265, 153.326264, 153.326163 specifications

Kenmore has long been recognized for its reliable and innovative home appliances, and its models 153.326264, 153.326265, 153.326162, and 153.326163 are no exception. These kitchen appliances, primarily focusing on mixers and food processors, combine advanced technology with user-friendly features to help streamline meal preparation.

The Kenmore 153.326264 is designed for those who appreciate versatility in cooking. Equipped with multiple mixing speeds, this model allows users to customize their mixing intensity depending on the task. From whipping delicate cream to kneading dough, the easy-to-use control interface provides precise adjustments. Its robust motor ensures efficient processing, reducing prep time significantly.

In contrast, the Kenmore 153.326265 focuses on food processing capabilities. This appliance boasts a powerful motor that can handle a variety of ingredients, from tough vegetables to hard cheeses. Its sharp blades and large capacity bowl make it an ideal choice for meal preps that require chopping, slicing, or grating. Additionally, the model features multiple attachments, including a dough blade and slicing disc, enhancing its functionality.

The Kenmore 153.326162 emphasizes compact design without sacrificing performance. This mixer is perfect for smaller kitchens yet offers a powerful motor that can tackle all mixing tasks. Its lightweight construction allows for easy handling and storage, while its sleek aesthetics can seamlessly blend into modern kitchen decor.

Lastly, the Kenmore 153.326163 integrates smart technology with traditional mixing capabilities. This model is equipped with a digital interface that includes preset mixing programs for various recipes. Users can simply select their desired program, and the appliance will automatically adjust speed and timing for optimal results. This feature is particularly beneficial for novice cooks who may be unsure of the right settings for different tasks.

Across these four models, Kenmore emphasizes durability, ease of use, and efficiency, catering to a wide range of culinary enthusiasts. With their combination of powerful motors, thoughtful design, and innovative features, these kitchen appliances are designed to make cooking enjoyable and hassle-free. Whether you're an avid home chef or simply looking to simplify your meal prep, these Kenmore models provide the tools needed to bring your culinary creations to life.
Top Page Image Contents