Kenmore 153.326162, 153.326265, 153.326264, 153.326163 owner manual

Page 15

If you are not familiar with electric codes and practices, or if you have any doubt, even the slightest doubt, in your ability to connect the wiring to this water heater, obtain the service of a competent electrician. Contact your Sears salesperson to arrange for a professional electrician.

WATER HEATERS EQUIPPED FOR ONE VOLTAGE ONLY: This water heater is equipped for one type voltage only. Check the rating plate near the bottom access panel for the correct voltage. DO NOT use this water heater with any voltage other than the one shown on the model rating plate. Failure to use the correct voltage can cause problems which can result in

DEATH, SERIOUS BODILY INJURY, OR PROPERTY DAMAGE. If you have any questions or doubts consult your electric company.

If wiring from your fuse box or circuit breaker box was aluminum for your old water heater, replace it with copper wire. If you wish to reuse the existing aluminum wire, have the connection at the water heater made by a competent electrician. Contact your Sears salesperson to arrange for a professional electrician.

1.Provide a way to easily shut off the electric power when working on the water heater. This could be with a circuit breaker or fuse block in the entrance box or a separate disconnect switch.

2.Install and connect a circuit directly from the main fuse or circuit breaker box. This circuit must be the right size and have its own fuse or circuit breaker. Refer to the chart in the “Product Specifications” section for the correct size wire and fuse or circuit breaker.

3.If metal conduit is used for the grounding conductor:

A.The grounding electrode conductor shall be of copper, aluminum, or copperclad aluminum. The material shall be of one continuous length without a splice or joint.

B.Rigid metal conduit, intermediate metal conduit, or electrical metallic tubing may be used for the grounding means if conduit or tubing is terminated in fittings approved for grounding.

C.Flexible metal conduit or flexible metallic tubing shall be permitted for grounding if all the following conditions are met:

The length in any ground return path does not exceed 6 feet.

The circuit conductors contained therein are protected by overcurrent devices rated at 20 amperes or less.

The conduit or tubing is terminated in fittings approved for grounding.

For complete grounding details and all allowable exceptions, refer to the current edition of the NEC - National Electrical Code NFPA 70.

4.A standard 1/2" conduit opening has been made in the water heater junction box for the conduit connection.

5.Wiring Diagrams, (see “Wiring Diagrams” section) have been supplied showing the two most common types of connections between the water heater and the power supply. You can easily see which type connection you have by removing the junction box cover on top of the water heater.

Two Wire Connection Diagram: is the most common requiring you to simply connect red to red, black to black, and the ground wire to the green ground screw in the junction box of the water heater.

Three Wire Connection Diagram: is used when you are connecting the water heater to a power supply that has a “Time Clock” or “Off Peak” meter. To make these connections refer to block 1 or 2 in this wiring diagram for the type of system you have.

NOTE: If you have purchased a three wire connection water heater but you are not on a “Time Clock” or “Off Peak” meter and have a standard two wire connection power supply, simply follow the connection diagram in block 3 of the three wire connection diagram.

6.Use wire nuts and connect the power supply wiring to the wires inside the water heater’s junction box.

7.The water heater must be electrically “grounded” by the installer. A green ground screw has been provided on the water heater’s junction box. Connect ground wire to this location.

8.Replace the wiring junction cover using the screw provided.

FIGURE 23.

15

Image 15
Contents Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A Power Miser Electric Water HeaterSafe INSTALLATION, USE and Service General Safety Table of Contents Introduction Product SpecificationsBasic Tools Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Materials NeededRemoving the Old Water Heater Installation InstructionsFacts to Consider About the Location Insulation BlanketsFacts to Consider About Convertible Lower Element Water Piping Valve and Pipe Insulation Temperature-Pressure Relief ValveTemperature-Pressure Relief Valve Optional Location Converting the Lower Element Filling the Water HeaterPage Wiring Page Wiring Diagrams Upper and Lower Thermostat Adjustments Service and AdjustmentTemperature Regulation Temperature SettingsTemperature-Pressure Relief Valve Operation Anode Rod InspectionDraining Element Cleaning/Replacement Thermostat Removal/ReplacementPage Page Service Drain Valve Washer ReplacementTroubleshooting Start Up ConditionsOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Model NO’S Repair Parts ListMY-HOME

153.326162, 153.326265, 153.326264, 153.326163 specifications

Kenmore has long been recognized for its reliable and innovative home appliances, and its models 153.326264, 153.326265, 153.326162, and 153.326163 are no exception. These kitchen appliances, primarily focusing on mixers and food processors, combine advanced technology with user-friendly features to help streamline meal preparation.

The Kenmore 153.326264 is designed for those who appreciate versatility in cooking. Equipped with multiple mixing speeds, this model allows users to customize their mixing intensity depending on the task. From whipping delicate cream to kneading dough, the easy-to-use control interface provides precise adjustments. Its robust motor ensures efficient processing, reducing prep time significantly.

In contrast, the Kenmore 153.326265 focuses on food processing capabilities. This appliance boasts a powerful motor that can handle a variety of ingredients, from tough vegetables to hard cheeses. Its sharp blades and large capacity bowl make it an ideal choice for meal preps that require chopping, slicing, or grating. Additionally, the model features multiple attachments, including a dough blade and slicing disc, enhancing its functionality.

The Kenmore 153.326162 emphasizes compact design without sacrificing performance. This mixer is perfect for smaller kitchens yet offers a powerful motor that can tackle all mixing tasks. Its lightweight construction allows for easy handling and storage, while its sleek aesthetics can seamlessly blend into modern kitchen decor.

Lastly, the Kenmore 153.326163 integrates smart technology with traditional mixing capabilities. This model is equipped with a digital interface that includes preset mixing programs for various recipes. Users can simply select their desired program, and the appliance will automatically adjust speed and timing for optimal results. This feature is particularly beneficial for novice cooks who may be unsure of the right settings for different tasks.

Across these four models, Kenmore emphasizes durability, ease of use, and efficiency, catering to a wide range of culinary enthusiasts. With their combination of powerful motors, thoughtful design, and innovative features, these kitchen appliances are designed to make cooking enjoyable and hassle-free. Whether you're an avid home chef or simply looking to simplify your meal prep, these Kenmore models provide the tools needed to bring your culinary creations to life.