Kenmore 153.326265, 153.326264 Facts to Consider About the Location, Insulation Blankets

Page 8

FIGURE 7.

Mineral buildup or sediment may have accumulated in the old water heater. This causes the water heater to be much heavier than normal and this residue, if spilled out, could cause staining.

Facts to Consider About the Location

You should carefully choose an indoor location for the new water heater, because the placement is a very important consideration for the safety of the occupants in the building and for the most economical use of the appliance. This water heater is not intended for outdoor installation.

Whether replacing an old water heater or putting the water heater in a new location, the following critical points must be observed.

•The location selected should be indoors as close to and as centralized with the water piping system as possible. This water heater, as well as all water heaters, will eventually leak. Do not install without adequate drainage provisions so water flow will not cause damage.

WATER HEATERS EVENTUALLY LEAK: Installation of the water heater must be accomplished in such a manner that if the tank or any connections should leak, the flow of water will not cause damage to the structure. When such locations cannot be avoided, a suitable drain pan should be installed under the water heater. Drain pans are available at your local Sears stores. Such drain pans must be piped to an adequate drain.

Water heater life depends upon water quality, water pressure and the environment in which the water heater is installed. Water heaters are sometimes installed in locations where leakage may result in property damage, even with the use of a drain pan piped to a drain. However, unanticipated damage can be reduced or prevented by a leak detector or water shut-off device used in conjunction with a piped drain pan. These devices are available

from some plumbing wholesalers and retailers, and detect and react to leakage in various ways:

•Sensors mounted in the drain pan that trigger an alarm or turn off the incoming water to the water heater when leakage is detected.

•Sensors mounted in the drain pan that turn off the water supply to the entire home when water is detected in the drain pan.

•Water supply shut-off devices that activate based on the water pressure differential between the cold water and hot water pipes connected to the water heater.

INSTALLATION IN RESIDENTIAL GARAGES: The water heater must be located and/or protected so it is not subject to physical damage by a moving vehicle.

•The location selection must provide adequate clearances for servicing and proper operation of the water heater.

Insulation Blankets

Insulation blankets are available to the general public for external use on electric water heaters but are not necessary with this product. The purpose of an insulation blanket is to reduce the standby heat loss encountered with storage tank heaters. Your water heater meets or exceeds the National Appliance Energy Conversation Act standards with respect to insulation and standby loss requirements, making an insulation blanket unnecessary.

Should you choose to apply an insulation blanket to this heater, you should follow these instructions below. Failure to follow these instructions can result in fire, serious personal injury, or death.

•Do not cover the temperature and pressure relief (T & P) valve with an insulation blanket.

•Do not cover the instruction manual. Keep it on the side of the water heater or nearby for future reference.

•Do obtain new warning and instruction labels for placement on the blanket directly over the existing labels.

Facts to Consider About the

Convertible Lower Element

The Upper Element (if a double element model) is a conventional 3800 watt element which only operates at its rated wattage on 240 volts. (See rating plate on the water heater).

The Lower Element of the water heater can be converted from operation at 3800 watts to 5500 watts on a 240 volt system.

Read and follow water heater warnings and instructions. If after reading these instructions in this manual, you do not understand any portion, call Sears Service Center.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Power Miser Electric Water Heater Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ASafe INSTALLATION, USE and Service General Safety Table of Contents Product Specifications IntroductionAdditional Tools Needed When Sweat Soldering Materials and Basic Tools NeededMaterials Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterFacts to Consider About Convertible Lower Element Facts to Consider About the LocationInsulation Blankets Water Piping Temperature-Pressure Relief Valve Valve and Pipe InsulationTemperature-Pressure Relief Valve Optional Location Filling the Water Heater Converting the Lower ElementPage Wiring Page Wiring Diagrams Service and Adjustment Temperature RegulationTemperature Settings Upper and Lower Thermostat AdjustmentsDraining Temperature-Pressure Relief Valve OperationAnode Rod Inspection Thermostat Removal/Replacement Element Cleaning/ReplacementPage Page Drain Valve Washer Replacement ServiceOperational Conditions TroubleshootingStart Up Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Repair Parts List Model NO’SMY-HOME

153.326162, 153.326265, 153.326264, 153.326163 specifications

Kenmore has long been recognized for its reliable and innovative home appliances, and its models 153.326264, 153.326265, 153.326162, and 153.326163 are no exception. These kitchen appliances, primarily focusing on mixers and food processors, combine advanced technology with user-friendly features to help streamline meal preparation.

The Kenmore 153.326264 is designed for those who appreciate versatility in cooking. Equipped with multiple mixing speeds, this model allows users to customize their mixing intensity depending on the task. From whipping delicate cream to kneading dough, the easy-to-use control interface provides precise adjustments. Its robust motor ensures efficient processing, reducing prep time significantly.

In contrast, the Kenmore 153.326265 focuses on food processing capabilities. This appliance boasts a powerful motor that can handle a variety of ingredients, from tough vegetables to hard cheeses. Its sharp blades and large capacity bowl make it an ideal choice for meal preps that require chopping, slicing, or grating. Additionally, the model features multiple attachments, including a dough blade and slicing disc, enhancing its functionality.

The Kenmore 153.326162 emphasizes compact design without sacrificing performance. This mixer is perfect for smaller kitchens yet offers a powerful motor that can tackle all mixing tasks. Its lightweight construction allows for easy handling and storage, while its sleek aesthetics can seamlessly blend into modern kitchen decor.

Lastly, the Kenmore 153.326163 integrates smart technology with traditional mixing capabilities. This model is equipped with a digital interface that includes preset mixing programs for various recipes. Users can simply select their desired program, and the appliance will automatically adjust speed and timing for optimal results. This feature is particularly beneficial for novice cooks who may be unsure of the right settings for different tasks.

Across these four models, Kenmore emphasizes durability, ease of use, and efficiency, catering to a wide range of culinary enthusiasts. With their combination of powerful motors, thoughtful design, and innovative features, these kitchen appliances are designed to make cooking enjoyable and hassle-free. Whether you're an avid home chef or simply looking to simplify your meal prep, these Kenmore models provide the tools needed to bring your culinary creations to life.
Top Page Image Contents