Kenmore 153.326163 Anode Rod Inspection, Temperature-Pressure Relief Valve Operation, Draining

Page 18

NOTE: It is not necessary to adjust the upper thermostat. However, if it is adjusted above the factory set point of 120°F (49°C), it is recommended that it not be set higher than the lower thermostat setting.

The upper and lower thermostats are adjustable if a different water temperature is desired. Read all warnings in the “Temperature-Regulation” section before proceeding.

1.Turn “OFF” the electric power to the water heater at the junction box.

2.Take off the upper and/or lower access panel, insulation cap with handle.

3.The slotted adjustment (using a screwdriver) can be turned

clockwise ( ) to increase the temperature setting or counter clockwise ( ) to decrease the temperature setting.

4.Replace the insulation cap with handle and access panel.

5.Turn “ON” the power supply.

Anode Rod Inspection

The anode rod is used to protect the tank from corrosion. Most hot water tanks are equipped with an anode rod. The submerged rod sacrifices itself to protect the tank. Instead of corroding the tank, water ions attack and eat away the anode rod. This does not affect the water’s taste or color. The rod must be maintained to keep the tank in operating condition.

Anode deterioration depends on the water conductivity, not necessarily water condition. A corroded or pitted anode rod indicates high water conductivity and should be checked and/ or replaced more often than an anode rod that appears to be intact. Replacement of a depleted anode rod can extend the life of your water heater. Inspection should be conducted by calling Sears Service Center. At a minimum the anode(s) should be checked annually after the warranty period.

Temperature-Pressure Relief

Valve Operation

The temperature-pressure relief valve must be manually operated at least once a year.

The temperature-pressure relief valve must be manually operated at least once a year. Caution should be taken to ensure that (1) no one is in front of or around the outlet of the temperature-pressure relief valve discharge line, and (2) the water manually discharged will not cause any property damage or bodily injury. The water may be extremely hot.

FIGURE 28.

If after manually operating the valve, it fails to completely reset and continues to release water, immediately close the cold water inlet to the water heater, follow the draining instructions, and replace the temperature-pressure relief valve with a new one.

Failure to install and maintain a new properly listed temperature- pressure relief valve will release the manufacturer from any claim which might result from excessive temperature or pressure.

If the temperature-pressure relief valve on the appliance weeps or discharges periodically, this may be due to thermal expansion. Your water heater may have a check valve installed in the water line or a water meter with a check valve. Consult your local Sears Service Center for further information. Do not plug the temperature-pressure relief valve.

Draining

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Power Miser Electric Water Heater Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.ASafe INSTALLATION, USE and Service General Safety Table of Contents Product Specifications IntroductionMaterials Needed Additional Tools Needed When Sweat SolderingMaterials and Basic Tools Needed Basic ToolsInstallation Instructions Removing the Old Water HeaterFacts to Consider About the Location Insulation BlanketsFacts to Consider About Convertible Lower Element Water Piping Temperature-Pressure Relief Valve Valve and Pipe InsulationTemperature-Pressure Relief Valve Optional Location Filling the Water Heater Converting the Lower ElementPage Wiring Page Wiring Diagrams Temperature Settings Service and AdjustmentTemperature Regulation Upper and Lower Thermostat AdjustmentsTemperature-Pressure Relief Valve Operation Anode Rod InspectionDraining Thermostat Removal/Replacement Element Cleaning/ReplacementPage Page Drain Valve Washer Replacement ServiceTroubleshooting Start Up ConditionsOperational Conditions AIR in HOT Water Faucets Water is TOO HOT Leakage Checkpoints Repair Parts List Model NO’SMY-HOME

153.326162, 153.326265, 153.326264, 153.326163 specifications

Kenmore has long been recognized for its reliable and innovative home appliances, and its models 153.326264, 153.326265, 153.326162, and 153.326163 are no exception. These kitchen appliances, primarily focusing on mixers and food processors, combine advanced technology with user-friendly features to help streamline meal preparation.

The Kenmore 153.326264 is designed for those who appreciate versatility in cooking. Equipped with multiple mixing speeds, this model allows users to customize their mixing intensity depending on the task. From whipping delicate cream to kneading dough, the easy-to-use control interface provides precise adjustments. Its robust motor ensures efficient processing, reducing prep time significantly.

In contrast, the Kenmore 153.326265 focuses on food processing capabilities. This appliance boasts a powerful motor that can handle a variety of ingredients, from tough vegetables to hard cheeses. Its sharp blades and large capacity bowl make it an ideal choice for meal preps that require chopping, slicing, or grating. Additionally, the model features multiple attachments, including a dough blade and slicing disc, enhancing its functionality.

The Kenmore 153.326162 emphasizes compact design without sacrificing performance. This mixer is perfect for smaller kitchens yet offers a powerful motor that can tackle all mixing tasks. Its lightweight construction allows for easy handling and storage, while its sleek aesthetics can seamlessly blend into modern kitchen decor.

Lastly, the Kenmore 153.326163 integrates smart technology with traditional mixing capabilities. This model is equipped with a digital interface that includes preset mixing programs for various recipes. Users can simply select their desired program, and the appliance will automatically adjust speed and timing for optimal results. This feature is particularly beneficial for novice cooks who may be unsure of the right settings for different tasks.

Across these four models, Kenmore emphasizes durability, ease of use, and efficiency, catering to a wide range of culinary enthusiasts. With their combination of powerful motors, thoughtful design, and innovative features, these kitchen appliances are designed to make cooking enjoyable and hassle-free. Whether you're an avid home chef or simply looking to simplify your meal prep, these Kenmore models provide the tools needed to bring your culinary creations to life.
Top Page Image Contents