Radio Shack Two-Zone Burglar Alarm System owner manual ˆ Testing the System, Using Annunciate Mode

Page 17

49-454.fm Page 17 Wednesday, January 17, 2001 10:37 AM

2.Hold down SETUP on the keypad until ARMED and READY slowly flash.

3.Within 30 seconds, enter the current password. If you entered the correct password, ARMED and READY flash quickly.

4.Enter a new password. ARMED and READY turn off. Enter the new password again to confirm. If the system accepts the password, READY flashes 3 times and the system returns to standby mode. If you entered an incor- rect password, ARMED flashes 3 times and the system returns to standby mode.

The duress code will be same as the password + 1 (i.e., if the password is 1579, the duress code is 1570. If the password is 1246, the duress code is 1247).

Note: If you do not enter the correct password within 30 sec- onds in Steps 3 or 4, simply start again from Step 2.

To restore the default password (1 2 3 4), press PASSWORD RESET on the alarm center.

USING ANNUNCIATE MODE

Annunciate mode lets you set the alarm system so it sounds a brief pre-alarm if it detects any change in the assigned zone.

1.If the system is disarmed and no zone is violated, hold down SETUP for about 2 seconds. ARMED and READY flash slowly.

2.Enter the current security code within 30 seconds. ARMED and READY flash rapidly.

3.Press ANNC (annunciate) once. ARMED and READY turn off.

4.To enable annunciate mode, press ENTER. READY flashes 3 times. If the alarm system detects any change in the assigned zone, it sounds a brief pre-alarm.

To disable annunciate mode, press CANCEL. READY flash- es 3 times.

SETTING THE ENTRY AND EXIT DELAY

DELAY TIME ADJ lets you adjust how long the alarm system waits before arming. If a sensor is activated in the Delayed Zone, then reset while the pre-alarm is sounding, the alarm will not sound. This gives you time to exit your home or office after arming the system.

DELAY TIME ADJ also lets you adjust how long the alarm system waits before sounding the alarm, to give you time to disarm the system. During this period, the pre-alarm sounds.

Notes:

•The pre-alarm sounds when any sensor is activated in the Delayed Zone. Use the pre-alarm as a reminder to disarm the system.

•Be sure to set DELAY TIME ADJ while the alarm center is disarmed.

There are six delay options can be selected. Rotate DELAY TIME ADJ (10, 20, 30, 40, 50 or 55) to set the desired number of minutes.

Note: The 50/55 second delay setting cannot be used for UL-recognized installation.

SYSTEM RESET

Press SYSTEM RESET to reset the password, alarm, and keypad.

ˆTesting the System

TESTING THE BATTERY

Although the alarm center automatically tests the backup battery each time you arm and disarm the system and once every 3 hours and 50 minutes, you can also press BATT TEST on the alarm center to test the battery at any time. Test the backup battery at least once per week.

Note: If you installed a new backup battery in the system, wait 24 hours for the alarm system to charge it before manu- ally testing it. While the battery is charging, BATT flashes. When the battery is charged, BATT goes off.

When you press BATT TEST, check BATT for the condition of the backup battery.

BATT Indicator

Meaning

 

 

 

 

Lit

AC power is low or off. Check the

 

AC adapter and AC power

 

 

Not lit

The battery is fully charged.

 

 

Flashing slowly

The battery is low.

 

 

BATT Indicator

 

Meaning

 

 

 

 

Flashing rapidly

The battery has insufficient power

 

due to one or more of the following

 

reasons:

 

•

No battery installed.

 

•

Faulty battery connection.

 

•

The fuse inside the alarm cen-

 

 

ter is blown (see “Replacing

 

 

the Fuse” on Page 19).

 

•

Battery is defective.

 

 

 

Notes:

•If the battery is low, defective or disconnected when the unit has AC power, the pre-alarm sounds for 5 seconds every minute.

•Enter the password and press CANCEL to stop the pre- alarm.

•After 3 hours 50 minutes, if the battery is still low or dis- connected, the pre-alarm sounds again.

Testing the System

17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Two-Zone Burglar Alarm System REQUIRED/OPTIONAL Accessories ˆ FeaturesSupplied Items Important NotesPower GND DATA2 Annc ˆ a Quick Look at Your Alarm Center/KeypadUnderstanding the System ˆ PreparationUnderstanding Zones Planning Your Security SystemInstant Zone Delayed Zone Room/Area Door Window Sensor Sounder Other System Planning WorksheetOther Ways to Improve Security Safeguarding Planning RecordsMaking a Shopping List Securing Your Home or OfficeNumber Model Serial No Value Insured Y/N Where/How Marked Property Inventory ListChoosing a Location for the Alarm Center Setting UP the SystemUsing the Tamper Switches Mounting the Alarm CenterSensors Choosing the ComponentsChoosing a Location for the Remote Keypad Automatic Telephone Dialer Sirens and LightsSystem Wiring Connections ˆ InstallationConnecting Remote Keypads Mounting the KeypadSetting the Keypad’s Address Connecting Sensors Into LoopsConnecting Loops of Sensors to the Alarm Center Jumpers on Normally-Closed TerminalsConnecting and Powering a Remote Security Device Connecting a PRE-ALARM BuzzerConnecting a Siren AND/OR Lights Connecting AC PowerFm Page 15 Wednesday, January 17, 2001 1037 AM Changing the Password Sounding a Panic Alarmˆ Operation Arming the SystemUsing Annunciate Mode ˆ Testing the SystemSetting the Entry and Exit Delay System ResetWeekly System Check Testing the Siren AND/OR LightsChecking the Indicators Replacing the Fuse Resetting the AC ADAPTER’S Circuit Breakerˆ Care Limited Ninety-Day Warranty ˆ Specifications

Two-Zone Burglar Alarm System specifications

The Radio Shack Two-Zone Burglar Alarm System is designed to provide homeowners and small business owners with effective security solutions. This system offers an excellent balance of functionality, reliability, and affordability, making it a popular choice for those looking to enhance their property's safety.

One of the standout features of the Radio Shack Two-Zone Burglar Alarm System is its dual-zone capability. This allows users to monitor multiple areas of their property separately. For example, one zone can be designated for exterior doors, while another can monitor interior spaces, which can help to prevent false alarms triggered by pets or other movements within the home. This feature is particularly useful for larger properties that require more than just a single-point monitoring system.

The system is equipped with multiple sensors, including door and window contacts, which can easily be installed to ensure comprehensive coverage. These sensors are designed to detect unauthorized entry and trigger the alarm whenever a door or window is opened. The system also includes passive infrared motion sensors that can identify movement within a designated area, adding an additional layer of security against intruders.

In terms of technologies, the Radio Shack Two-Zone Burglar Alarm System utilizes a microprocessor-controlled control panel, which is at the heart of the system's operations. This logic board processes signals from all connected sensors and determines when to trigger the alarm. The system can provide alerts via a loud siren, while also allowing for notifications to be sent to the owner’s smartphone or other devices, depending on the model.

The installation process for the Radio Shack burglar alarm system is user-friendly, designed for ease even for those who may not be technically savvy. The system typically includes clear instructions and mounting hardware, making setup straightforward. Users can customize their alarm system according to their specific needs and property layout, which further enhances usability.

Another important characteristic of the Radio Shack Two-Zone Burglar Alarm System is the option for battery backup. This ensures that the alarm continues to operate even during power outages, allowing for uninterrupted security coverage. Moreover, the system is frequently praised for its durability and resistance to environmental factors, making it a robust choice for various settings.

Overall, the Radio Shack Two-Zone Burglar Alarm System represents a practical and efficient security solution, combining essential features, advanced technology, and user-friendly installation, all designed to meet the security needs of modern users.
Top Page Image Contents