New Buck Corporation 94NC installation instructions Installation Procedure, Positioning Heater

Page 10

INSTALLATION PROCEDURE

(Use a chimney connector or a Listed Direct or Positive Connect) (See Page 6).

POSITIONING HEATER

When positioning heater, the following conditions MUST be met! (See Figure 5).

1. The front

of flue opening must be positioned

BEHIND

rear edge of the lintel to ensure proper

draft. (See Figure 5).

2. Center heater in fireplace opening.

FRONTOF FIREPLACE

FLUE OPENING

FIGURE 5

POSITIONING

MOUNTING TRIM PANELS

 

 

 

NOTE: Mount top trim panel so that it sits in front of

 

 

top of side trim panels.

 

 

 

After unit is positioned, mark mounting position of trim

 

 

panels as follows:

 

 

 

1.

Place side trim panels flat against

face of fireplace.

 

 

 

Mark down front edge of trim panel with a pencil to

 

 

 

make a vertical reference line. (See Figure 6).

 

 

2.

Set

top (long) trim panel in place on top of unit.

 

 

 

The

panel should be flat against the outside face

 

 

 

of

fireplace, and standing vertically. Mark along

 

 

 

lower edge of trim panel with a

pencil to make a

 

 

 

reference line for mounting.

 

 

 

3.

Slide unit out of fireplace far enough to work

FIGURE 6

MOUNTING TRIM PANELS

 

behind trim panel reference lines.

 

4.Mount side trim panels. (See Figure 6).

a.Position trim panel on reference line.

b.Drill mounting holes in center of trim panel mounting brackets to allow for adjustment in and out if neces- sary.

c.Mount trim panel using self-tapping screws provided.

5.Place top panel back on reference mark. Take top trim panel mounting bracket supplied with unit. Position bracket so it overlaps rear lip of top trim panel. Drill mounting holes in top of stove using holes in bracket as guide. Tighten down screws.

6.Now, follow installation procedures in listed direct connect or positive connect kit you are using and install

heater and connect kit in fireplace. If not using one of installation methods shown on (Page 7), continue.

7.Slide unit back into fireplace. Check to be sure that trim panels are properly positioned and lie flat against front of fireplace. If one or more of panels is out of position, slide unit out and reset by loosening the mounting screws and repositioning in the slot. Reinstall top trim panel by sliding rear lip of top trim panel

underneath front lip of mounting bracket already secured to top of unit.

Page 8

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Safety Notice Fireplace Insert & FreestandingPage Table of Contents INSTALLATION, OPERATION, Maintenance Instructions Model 94NC Important InstructionsSection IntroductionModel 94NC Wood Stove EPA Compliance StatusMasonry Insert Installation Minimum Clearance Masonry InsertMasonry Insert Installation Possible Tools Needed for InstallationInstallation Preparation Installation OptionsOption a Figure Installation Procedure Positioning HeaterFinal Check Page Section Residential Freestanding Installation Preparing Stove for InstallationChimney Page Installing a thimble through combustible wall Wall Exit Into Metal Tee-Box Wall Exit Into Masonry Flue Using Single Wall Pipe Page Final Check Model 94NC Section Wood Heater Safety Section VII Operation Building a FireRoom AIR Blower Operation Section Troubleshooting Problem Possible Cause SolutionTroubleshooting Replacement Parts For Model 94NC Procedure Warranty Time PeriodsProducts Covered Other Rights Conditions and ExclusionsOwner Registration Card

94NC specifications

New Buck Corporation's 94NC is a premium synthetic lubricant designed to meet the demands of modern industry. This high-performance product is particularly noted for its versatility and ability to perform in a wide range of applications, making it a go-to choice for professionals in various sectors, including automotive, manufacturing, and heavy machinery.

One of the standout features of 94NC is its superior thermal stability. This characteristic ensures that the lubricant maintains its integrity and performance even under extreme temperature variations. As a result, equipment operates more efficiently, with reduced downtime and maintenance costs. This thermal resilience allows 94NC to provide a consistent lubricating film, safeguarding components against wear and tear over extended periods.

In terms of technology, 94NC employs advanced additive formulations that enhance its performance characteristics. These additives include anti-wear agents, detergents, and rust inhibitors, which together work to protect machinery and prolong its lifespan. The anti-wear properties of 94NC are particularly impressive, ensuring that metal-to-metal contact is minimized, thus reducing friction and extending the life of critical components.

The viscosity of 94NC is another pivotal aspect of its formulation. Designed to perform effectively across a wide viscosity range, it ensures optimal lubrication under varying operational conditions. This adaptability is key in industries where equipment operates under heavy loads and fluctuating speeds, allowing the lubricant to maintain its effectiveness regardless of the strain placed upon it.

Moreover, New Buck Corporation has prioritized environmental impact in the development of 94NC. The lubricant is designed to be less harmful to the environment compared to traditional oils, utilizing biodegradable components wherever feasible. This commitment to sustainability appeals to businesses that are increasingly mindful of their ecological footprint.

Overall, New Buck Corporation's 94NC synthetic lubricant exemplifies a blend of cutting-edge technology and user-centric characteristics. With its exceptional thermal stability, advanced additive formulations, flexible viscosity, and environmental consciousness, 94NC stands as a robust solution for industries looking to enhance operational efficiency while also being considerate of environmental impacts. This makes it a wise investment for any business seeking reliable and effective lubrication solutions.
Top Page Image Contents