New Buck Corporation 94NC installation instructions Final Check

Page 11

8.Obtain outer trim kit provided with insert kit and slip over top and sides of trim panels.(See Figure 7). (Top ends of outer trim may need to be trimmed to fit).

9.Using insulation provided, peel and stick to back of panels overlapping fireplace dimensions by 1" on each side and top. (See Figure 8).

10.Next using high heat silicone or furnace cement run heavy bead of caulking around where back of panels meet stove. (See Figure 8).

11.Slide unit back into fireplace. Check to be sure that trim panels (and outer trim) are properly positioned and lie flat against front of fireplace. If panels are out of position, slide unit out and reset by loosening mounting screws and repositioning in slot. With bar lift stove up in front. Place insulation across front at bottom and surface of hearth or bottom of fireplace to make complete seal.

12.To check seal of panels, use candle flame and go around entire area sealed by silicone and insulation. If flame leans toward inside of fireplace, add additional insulation. This ensures an airtight seal.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outer Trim

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIGURE 7

FIGURE 8

Top Trim Panel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Side Trim Panel

INSULATION

Buck Stove

Primary Air Control

FINAL CHECK

1.Recheck specified clearances.

2.Remove all foreign material from firebox area.

3.Open primary air control.

Primary Air Control: The primary air intake draft control is located at right bottom side of hearth. It is operated by moving handle out to open (to allow air into firebox) or in (to control or close off) air into firebox. (See Figure 7).

4.Plug power cord into a 115V AC outlet. “Do not run cord under unit or in high traffic areas.

5.Place crumpled pieces of newspaper in stove. Light it and close door. Ensure that stove draws properly through primary draft.

NOTE: “Do not use grate or elevate fire. Build wood fire directly on fire box bottom.”

6.Check for smoke leaks around door.

7.Open door and check for smoke escaping from front of stove. Smoking usually indicates a defective or poorly positioned chimney. Some chimneys with a marginal draft can be pre-heated by lighting newspaper and holding it near open damper with a poker or fire tong. Once chimney heats up, a proper draft can usually be obtained.

If a thorough review of Troubleshooting Guide in rear of manual does not reveal

problem, contact your dealer for assistance.

Page 9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Fireplace Insert & Freestanding Safety NoticePage Table of Contents Important Instructions INSTALLATION, OPERATION, Maintenance Instructions Model 94NCIntroduction SectionEPA Compliance Status Model 94NC Wood StoveMinimum Clearance Masonry Insert Masonry Insert InstallationInstallation Options Possible Tools Needed for InstallationInstallation Preparation Masonry Insert InstallationOption a Figure Positioning Heater Installation ProcedureFinal Check Page Preparing Stove for Installation Section Residential Freestanding InstallationChimney Page Installing a thimble through combustible wall Wall Exit Into Metal Tee-Box Wall Exit Into Masonry Flue Using Single Wall Pipe Page Final Check Model 94NC Section Wood Heater Safety Building a Fire Section VII OperationRoom AIR Blower Operation Problem Possible Cause Solution Section TroubleshootingTroubleshooting Replacement Parts For Model 94NC Products Covered Warranty Time PeriodsProcedure Owner Registration Card Conditions and ExclusionsOther Rights

94NC specifications

New Buck Corporation's 94NC is a premium synthetic lubricant designed to meet the demands of modern industry. This high-performance product is particularly noted for its versatility and ability to perform in a wide range of applications, making it a go-to choice for professionals in various sectors, including automotive, manufacturing, and heavy machinery.

One of the standout features of 94NC is its superior thermal stability. This characteristic ensures that the lubricant maintains its integrity and performance even under extreme temperature variations. As a result, equipment operates more efficiently, with reduced downtime and maintenance costs. This thermal resilience allows 94NC to provide a consistent lubricating film, safeguarding components against wear and tear over extended periods.

In terms of technology, 94NC employs advanced additive formulations that enhance its performance characteristics. These additives include anti-wear agents, detergents, and rust inhibitors, which together work to protect machinery and prolong its lifespan. The anti-wear properties of 94NC are particularly impressive, ensuring that metal-to-metal contact is minimized, thus reducing friction and extending the life of critical components.

The viscosity of 94NC is another pivotal aspect of its formulation. Designed to perform effectively across a wide viscosity range, it ensures optimal lubrication under varying operational conditions. This adaptability is key in industries where equipment operates under heavy loads and fluctuating speeds, allowing the lubricant to maintain its effectiveness regardless of the strain placed upon it.

Moreover, New Buck Corporation has prioritized environmental impact in the development of 94NC. The lubricant is designed to be less harmful to the environment compared to traditional oils, utilizing biodegradable components wherever feasible. This commitment to sustainability appeals to businesses that are increasingly mindful of their ecological footprint.

Overall, New Buck Corporation's 94NC synthetic lubricant exemplifies a blend of cutting-edge technology and user-centric characteristics. With its exceptional thermal stability, advanced additive formulations, flexible viscosity, and environmental consciousness, 94NC stands as a robust solution for industries looking to enhance operational efficiency while also being considerate of environmental impacts. This makes it a wise investment for any business seeking reliable and effective lubrication solutions.
Top Page Image Contents