New Buck Corporation 94NC installation instructions Section VII Operation, Building a Fire

Page 23

SECTION VII OPERATION

This section of the manual is to help you get maximum efficiency and maximum smoke (particulate) reduction from your heater. If you should experience any difficulty or have any questions concerning your heater, contact your dealer for assistance. NOTE: The manufacturer recommends that for maximum performance burn natural seasoned hard wood.

Build a fire for maximum efficiency. This model burns wood and extracts heat so efficiently, a large fire is not necessary. A large fire not only wastes energy, it usually results in home being too warm for comfort.

The following steps will serve as a guide for operating your stove.

BUILDING A FIRE

1.Open door.

2.Open primary air control. Primary Air Controls: The primary air intake draft control is located at right bottom side of hearth. It is operated by moving handle out to open (to allow air into firebox) or in (to control or close off) air into firebox.

3.Twist two pieces of non-colored newspaper into a roll and place them on floor of firebox.

NOTE: “Do not use grate or elevate fire. Build wood fire directly on inner bottom of fire box.”

4.This model is not designed for use of grates, andirons or other methods of supporting fuel.

5.Lay several pieces of dry kindling on top of newspaper.

6.Place three or four small pieces of firewood, 2"-3" in diameter, on top of kindling.

7.Light newspaper in front. Close and latch door. Don't leave fire unattended at this point.

The draft system of heater should start quickly. It may be necessary to preheat chimney to get draft started. To do this, open door and add newspaper to top rear of wood. Light or let this paper ignite and allow to burn while holding the door slightly cracked. Once draft has started, close and lock door. You are over- heating the unit if the chimney and or connector glows red.

8.NOTE: After embers and a coal bed have been established, load heater with seasoned natural hard wood, placing it length way front to rear.

NOTE: THE FUELING DOOR MUST REMAIN CLOSED DURING OPERATION.

BURN RATE:

LOW

MED-LOW

MED-HI

HI

AIR SETTINGS:

1/32”

5/32”

9/32”

WIDE OPEN

Your stove is equipped with a automatic thermostat. When stove gets hot enough, thermostat will activate room air blower. Set fan speed on low, when burn on low, med- low, med-high. Set fan speed on high when burn on high.

NOTE: When refueling or removing ashes turn “OFF” room air blower. Be sure to turn room air blower back on when finished.

NOTE: Do not run power cord underneath heater or in walk way or heavy traffic areas.

Page 21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Fireplace Insert & Freestanding Safety NoticePage Table of Contents Important Instructions INSTALLATION, OPERATION, Maintenance Instructions Model 94NCIntroduction SectionEPA Compliance Status Model 94NC Wood StoveMinimum Clearance Masonry Insert Masonry Insert InstallationInstallation Options Possible Tools Needed for InstallationInstallation Preparation Masonry Insert InstallationOption a Figure Positioning Heater Installation ProcedureFinal Check Page Preparing Stove for Installation Section Residential Freestanding InstallationChimney Page Installing a thimble through combustible wall Wall Exit Into Metal Tee-Box Wall Exit Into Masonry Flue Using Single Wall Pipe Page Final Check Model 94NC Section Wood Heater Safety Building a Fire Section VII OperationRoom AIR Blower Operation Problem Possible Cause Solution Section TroubleshootingTroubleshooting Replacement Parts For Model 94NC Products Covered Warranty Time PeriodsProcedure Owner Registration Card Conditions and ExclusionsOther Rights

94NC specifications

New Buck Corporation's 94NC is a premium synthetic lubricant designed to meet the demands of modern industry. This high-performance product is particularly noted for its versatility and ability to perform in a wide range of applications, making it a go-to choice for professionals in various sectors, including automotive, manufacturing, and heavy machinery.

One of the standout features of 94NC is its superior thermal stability. This characteristic ensures that the lubricant maintains its integrity and performance even under extreme temperature variations. As a result, equipment operates more efficiently, with reduced downtime and maintenance costs. This thermal resilience allows 94NC to provide a consistent lubricating film, safeguarding components against wear and tear over extended periods.

In terms of technology, 94NC employs advanced additive formulations that enhance its performance characteristics. These additives include anti-wear agents, detergents, and rust inhibitors, which together work to protect machinery and prolong its lifespan. The anti-wear properties of 94NC are particularly impressive, ensuring that metal-to-metal contact is minimized, thus reducing friction and extending the life of critical components.

The viscosity of 94NC is another pivotal aspect of its formulation. Designed to perform effectively across a wide viscosity range, it ensures optimal lubrication under varying operational conditions. This adaptability is key in industries where equipment operates under heavy loads and fluctuating speeds, allowing the lubricant to maintain its effectiveness regardless of the strain placed upon it.

Moreover, New Buck Corporation has prioritized environmental impact in the development of 94NC. The lubricant is designed to be less harmful to the environment compared to traditional oils, utilizing biodegradable components wherever feasible. This commitment to sustainability appeals to businesses that are increasingly mindful of their ecological footprint.

Overall, New Buck Corporation's 94NC synthetic lubricant exemplifies a blend of cutting-edge technology and user-centric characteristics. With its exceptional thermal stability, advanced additive formulations, flexible viscosity, and environmental consciousness, 94NC stands as a robust solution for industries looking to enhance operational efficiency while also being considerate of environmental impacts. This makes it a wise investment for any business seeking reliable and effective lubrication solutions.
Top Page Image Contents