New Buck Corporation 94NC installation instructions

Page 15

Step (b): Calculate R of proposed system. 4” brick of C=1.25, therefore Rbrick = 1/C = 1/1.25 =0.80 1/8” mineral board of K = 0.29, therefore Rmin.bd. =1/029 x0.125 = 0.431

Step (c): Compare proposed system R of 1.231 to specified R of 0.893. Since proposed system R is greater than required , the system is acceptable.

Definitions:

 

 

 

Btu

 

W

 

 

Thermal conductance

=

C

=

=

 

 

(hr)(ft²)(°F)

(m²)(°K)

 

 

Thermal conductance

=

K

=

(Btu)(inch)

=

W

=

(Btu)

(hr)(ft²)(°F)

(m)(°K)

(hr)(ft)(°F)

Thermal conductance

= R =

(ft²)(hr)(°F)

=

(m²)(°K)

 

 

 

 

 

 

Btu

 

W

 

 

Install in accordance with 24 CFR, Part 3280 (HUD).

CAUTION

SPECIAL METHODS ARE REQUIRED WHEN PASSING THROUGH A WALL OR CEILING. SEE INSTRUCTIONS AND BUILDING CODES. “DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.”

DETERMINING CHIMNEY LOCATION

A.CEILINGEXIT ( Using 8” inch Diameter Residential Single Wall (minimum 24-ga.) Black Chimney Connector and any listed 2100 UL 103 HT type Chimney System ). (See Page 14).

1. Suspend a plumb bob from ceiling above unit so that weight is hanging in center of flue exit. (A small weight on a string will serve as a plumb bob). Mark ceiling where string is suspended to locate center of chimney.

2.After locating center of hole, install ceiling support box, chimney flashing and rain cap per chimney manufacturer’s instructions.

Now connect stove and ceiling support box using #24 ga. minimum blue or black steel connector pipe (DO NOT USE GALVANIZED PIPE). Connect each section so crimped end faces downward, and secure each section to each other using at least three (3) sheet metal screws or rivets. Also use three (3) sheet metal screws to fasten pipe to collar on heater. (See Figure 10. Page 15).

Page 13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Fireplace Insert & Freestanding Safety NoticePage Table of Contents Important Instructions INSTALLATION, OPERATION, Maintenance Instructions Model 94NCIntroduction SectionEPA Compliance Status Model 94NC Wood StoveMinimum Clearance Masonry Insert Masonry Insert InstallationInstallation Options Possible Tools Needed for InstallationInstallation Preparation Masonry Insert InstallationOption a Figure Positioning Heater Installation ProcedureFinal Check Page Preparing Stove for Installation Section Residential Freestanding InstallationChimney Page Installing a thimble through combustible wall Wall Exit Into Metal Tee-Box Wall Exit Into Masonry Flue Using Single Wall Pipe Page Final Check Model 94NC Section Wood Heater Safety Building a Fire Section VII OperationRoom AIR Blower Operation Problem Possible Cause Solution Section TroubleshootingTroubleshooting Replacement Parts For Model 94NC Warranty Time Periods ProcedureProducts Covered Conditions and Exclusions Other RightsOwner Registration Card

94NC specifications

New Buck Corporation's 94NC is a premium synthetic lubricant designed to meet the demands of modern industry. This high-performance product is particularly noted for its versatility and ability to perform in a wide range of applications, making it a go-to choice for professionals in various sectors, including automotive, manufacturing, and heavy machinery.

One of the standout features of 94NC is its superior thermal stability. This characteristic ensures that the lubricant maintains its integrity and performance even under extreme temperature variations. As a result, equipment operates more efficiently, with reduced downtime and maintenance costs. This thermal resilience allows 94NC to provide a consistent lubricating film, safeguarding components against wear and tear over extended periods.

In terms of technology, 94NC employs advanced additive formulations that enhance its performance characteristics. These additives include anti-wear agents, detergents, and rust inhibitors, which together work to protect machinery and prolong its lifespan. The anti-wear properties of 94NC are particularly impressive, ensuring that metal-to-metal contact is minimized, thus reducing friction and extending the life of critical components.

The viscosity of 94NC is another pivotal aspect of its formulation. Designed to perform effectively across a wide viscosity range, it ensures optimal lubrication under varying operational conditions. This adaptability is key in industries where equipment operates under heavy loads and fluctuating speeds, allowing the lubricant to maintain its effectiveness regardless of the strain placed upon it.

Moreover, New Buck Corporation has prioritized environmental impact in the development of 94NC. The lubricant is designed to be less harmful to the environment compared to traditional oils, utilizing biodegradable components wherever feasible. This commitment to sustainability appeals to businesses that are increasingly mindful of their ecological footprint.

Overall, New Buck Corporation's 94NC synthetic lubricant exemplifies a blend of cutting-edge technology and user-centric characteristics. With its exceptional thermal stability, advanced additive formulations, flexible viscosity, and environmental consciousness, 94NC stands as a robust solution for industries looking to enhance operational efficiency while also being considerate of environmental impacts. This makes it a wise investment for any business seeking reliable and effective lubrication solutions.
Top Page Image Contents