New Buck Corporation 94NC installation instructions Final Check

Page 20

FINAL CHECK

1.Recheck specified clearances.

2.Remove all foreign material from firebox area.

3.Open primary air control. Primary Air Controls: The primary air intake control is located at right bottom side of hearth. It is operated by moving the handle out to open (to allow air into the firebox) or in (to control or close off) air into the firebox.

4.

Plug

power cord into a 115V AC outlet when to see if motor and blower works. “Do not

 

run power cord under unit or in high traffic areas”.

 

5.

Place crumpled pieces of newspaper in stove. Light it and close

door. Ensure

 

that

stove draws properly through primary draft.

 

6.

Check for smoke leaks around door.

 

CAUTION

Open door and check for smoke escaping from front of the stove. Smoking usually indicates a defective or poorly positioned chimney. Some chimneys with a marginal draft can be preheated by lighting newspaper and holding it near open damper with a poker or fire tong. Once chimney heats up, a proper draft can usually be obtained.

If a thorough review of Troubleshooting Guide in rear of manual does not reveal problem, contact your dealer for assistance.

CAUTION

The unit is painted with a specially formulated high temperature paint that cures during the first two or three firings. You may notice a slight smoking effect and an odor of burning paint when you build the first fires. This is normal and is not a cause for alarm. In some cases, these fumes will activate a smoke alarm. Opening a window near unit will allow these fumes to escape. DO NOT build a large, roaring fire until this curing is complete or heater finish may be damaged.

Page 18

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Safety Notice Fireplace Insert & FreestandingPage Table of Contents INSTALLATION, OPERATION, Maintenance Instructions Model 94NC Important InstructionsSection IntroductionModel 94NC Wood Stove EPA Compliance StatusMasonry Insert Installation Minimum Clearance Masonry InsertPossible Tools Needed for Installation Installation PreparationMasonry Insert Installation Installation OptionsOption a Figure Installation Procedure Positioning HeaterFinal Check Page Section Residential Freestanding Installation Preparing Stove for InstallationChimney Page Installing a thimble through combustible wall Wall Exit Into Metal Tee-Box Wall Exit Into Masonry Flue Using Single Wall Pipe Page Final Check Model 94NC Section Wood Heater Safety Section VII Operation Building a FireRoom AIR Blower Operation Section Troubleshooting Problem Possible Cause SolutionTroubleshooting Replacement Parts For Model 94NC Products Covered Warranty Time PeriodsProcedure Owner Registration Card Conditions and ExclusionsOther Rights

94NC specifications

New Buck Corporation's 94NC is a premium synthetic lubricant designed to meet the demands of modern industry. This high-performance product is particularly noted for its versatility and ability to perform in a wide range of applications, making it a go-to choice for professionals in various sectors, including automotive, manufacturing, and heavy machinery.

One of the standout features of 94NC is its superior thermal stability. This characteristic ensures that the lubricant maintains its integrity and performance even under extreme temperature variations. As a result, equipment operates more efficiently, with reduced downtime and maintenance costs. This thermal resilience allows 94NC to provide a consistent lubricating film, safeguarding components against wear and tear over extended periods.

In terms of technology, 94NC employs advanced additive formulations that enhance its performance characteristics. These additives include anti-wear agents, detergents, and rust inhibitors, which together work to protect machinery and prolong its lifespan. The anti-wear properties of 94NC are particularly impressive, ensuring that metal-to-metal contact is minimized, thus reducing friction and extending the life of critical components.

The viscosity of 94NC is another pivotal aspect of its formulation. Designed to perform effectively across a wide viscosity range, it ensures optimal lubrication under varying operational conditions. This adaptability is key in industries where equipment operates under heavy loads and fluctuating speeds, allowing the lubricant to maintain its effectiveness regardless of the strain placed upon it.

Moreover, New Buck Corporation has prioritized environmental impact in the development of 94NC. The lubricant is designed to be less harmful to the environment compared to traditional oils, utilizing biodegradable components wherever feasible. This commitment to sustainability appeals to businesses that are increasingly mindful of their ecological footprint.

Overall, New Buck Corporation's 94NC synthetic lubricant exemplifies a blend of cutting-edge technology and user-centric characteristics. With its exceptional thermal stability, advanced additive formulations, flexible viscosity, and environmental consciousness, 94NC stands as a robust solution for industries looking to enhance operational efficiency while also being considerate of environmental impacts. This makes it a wise investment for any business seeking reliable and effective lubrication solutions.
Top Page Image Contents