Heat & Glo LifeStyle BAY-38HV manual Installing Vent Components

Page 19

B. Installing Vent Components

1.Attach the First Vent Component to the Starting Collars

To attach the first vent component to the starting collars of the fireplace:

•Apply a 3/8 inch (9.5mm) bead of stove cement around the 4 inch (102mm) fireplace starting collar.

•Make sure that the fireplace rope gasket supplied with the fireplace seals between the first 6-5/8 inch (168mm) vent component and the outer fireplace wrap.

•Lock the vent components into place by sliding the con- centric pipe sections with four (4) equally spaced interior beads into the fireplace collar or previously installed com- ponent end with four (4) equally spaced indented sections.

•When the internal beads of each 6-5/8 inch (168mm) outer pipe line up, rotate the pipe section clockwise about one-quarter (1/4) turn. The vent pipe is now locked together.

STARTING

COLLAR

STOVE

SEALANT

BEAD

FIRST VENT

COMPONENT

1 INCH (25.4mm)

Figure 15. Attaching the First Vent Component to the Starting Collars

!WARNING: A 3/8 INCH (9.5 MM) BEAD OF STOVE CEMENT MUST BE PLACED AROUND

THE 4 INCH (102 MM) FIREPLACE STARTING COL-

LAR BEFORE ATTACHING THE FIRST VENT COM- PONENT. FAILURE TO SEAL THIS JOINT MAY CAUSE THE FIREPLACE TO OPERATE IMPROPER- LY. SEE THE DIAGRAM .

!WARNING: ENSURE THAT THE FIBER- GLASS ROPE GASKET SUPPLIED WITH

THE FIREPLACE SEALS BETWEEN THE FIRST VENT COMPONENT AND THE OUTER FIREPLACE WRAP.

If the installation is for a termination cap attached directly to the fireplace, skip to the sections, Install Firestops and Vent Termination.

2. Continue Adding Vent Components

•Continue adding vent components, locking each succeed- ing component into place.

•Ensure that each succeeding vent component is secure- ly fitted and locked into the preceding component in the vent system.

•90° elbows may be installed and rotated to any point around the preceding component’s vertical axis. If an el- bow does not end up in a locked position with the preced- ing component, attach with a minimum of two (2) 1/2” sheet metal screws.

Figure 16. Adding Venting Components

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents Standing Pilot Ignition DSI Ignition Service PartsDF-38HV-EP BAY-38HV Service Parts List / Liste des pièces de rechangeCertification High Altitude InstallationsInstallation Codes Appliance CertificationIntroducing the Heat-N-Glo Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the BAY-38HV Clearance Requirements Fireplace Dimensions and LocationsConstructing the Chase Locating the FireplaceVertical and Horizontal Vent Runs Framing the FireplacePage Vent System Approvals Installing the Vent SystemIdentifying Vent Components Vent System Components and Termination KitsMAX .4 M Straight UP Vertical VentingStraight OUT Horizontal Venting Venting with Venting with ONE 1 90 ElbowONE 1 90 Elbow Venting with TWO Venting with TWO 2 90 Elbows Venting with Three 3 90 Elbows Venting with three 90 elbowsVenting with Three 3 90 Elbows Attach the First Vent Component to the Starting Collars Installing Vent ComponentsHole and Vent Pipe Install Support BracketsCeiling Firestop Ceiling Side Hole & New Framing MembersPointing UP Vent TerminationVent Termination Minimum Clearances =VENT Terminal =AIR Supply InletMinimum Height from Roof to Lowest Discharge Opening Gas Control Systems Positioning, Leveling, and Securing the FireplaceDSI Gas Pressure Requirements Gas Supply LineTo Check for GAS Leaks Wall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Optional AccessoriesDirect Spark Ignition Wiring Diagram For Direct Spark Ignition DSI Wiring Appliance RequirementsSealant Material FinishingHearth Extensions Placing the Ember Material Installing Trim, Logs, and Ember MaterialInstalling the Trim Positioning the LogsBefore Lighting the Fireplace After the InstallationLighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance

BAY-38HV specifications

The Heat & Glo LifeStyle BAY-38HV is a cutting-edge gas fireplace designed to enhance the ambience of any home while providing efficiency and convenience. This innovative unit combines modern aesthetics with advanced technology, making it a popular choice among homeowners seeking both form and function in their heating solutions.

One of the standout features of the BAY-38HV is its sleek, contemporary design, which allows it to seamlessly integrate into various interior styles. With its clean lines and expansive viewing area, the fireplace creates a focal point in any room, offering a warm and inviting atmosphere. The heat-resistant glass front provides a clear view of the flames, ensuring that the beauty of the fire can be enjoyed from multiple angles.

In terms of technology, the BAY-38HV is equipped with the latest in gas fireplace innovations. It incorporates an advanced IntelliFire ignition system, allowing for easy operation with the simple push of a button. Users can control the flame height and heat output directly from a remote, providing complete convenience and customizability. This makes it an excellent option for those who want to adjust the ambiance of their space effortlessly.

Efficiency is another key characteristic of the BAY-38HV. The fireplace boasts a high efficiency rating, ensuring that the warmth generated is maximized while minimizing energy consumption. This efficient performance not only contributes to a more comfortable home but also helps in reducing heating costs, making it an environmentally friendly choice.

The BAY-38HV also features an array of customizable options, including various log styles and ember bed choices. This allows homeowners to tailor the appearance of their fireplace to suit their individual preferences. Additionally, its compatibility with zone heating systems offers an effective solution for those looking to heat specific areas of their home without relying on central heating.

Safety is paramount with the Heat & Glo LifeStyle BAY-38HV. It includes protective features such as a safety screen and automatic shut-off mechanisms, providing peace of mind for families and individuals.

In summary, the Heat & Glo LifeStyle BAY-38HV gas fireplace is an exemplary model that combines stylish design with advanced technology. Its ease of use, efficiency, customization options, and safety features make it an ideal choice for anyone looking to enhance their living space with the charm and comfort of a gas fireplace.
Top Page Image Contents