Heat & Glo LifeStyle BAY-38HV manual Minimum Height from Roof to Lowest Discharge Opening

Page 24

For Vertical Terminations - To locate the vent and install the vent sections:

•Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint.

•Make the outline of the roof hole around the centerpoint nail.

•The size of the roof hole framing dimensions depend on the pitch of the roof. There MUST BE a 1-inch (25.4mm) clear- ance from the vertical vent pipe to combustible materials.

•Mark the roof hole accordingly.

•Cover the opening of the installed vent pipes.

•Cut and frame the roof hole.

•Use framing lumber the same size as the roof rafters and install the frame securely. Flashing anchored to the frame must withstand heavy winds.

•Continue to install concentric vent sections up through the roof hole (for inside vent installations) or up past the roof line until you reach the appropriate distance above the roof (for outside terminations).

!WARNING: MAJOR U.S. BUILDING CODES SPECIFY MINIMUM CHIMNEY AND/OR

VENT HEIGHT ABOVE THE ROOF TOP. THESE MIN- IMUM HEIGHTS ARE NECESSARY IN THE INTER- EST OF SAFETY. SEE THE FOLLOWING DIAGRAM FOR MINIMUM HEIGHTS, PROVIDED THE TERMI- NATION CAP IS AT LEAST TWO (2) FEET FROM A VERTICAL WALLAND 2-FEET BELOW A HORIZON- TAL OVERHANG.

NOTE: This also pertains to vertical vent systems in- stalled on the outside of the building.

To seal the roof hole, and to divert rain and snow from the vent system:

•Attach a flashing to the roof using nails, and use a non- hardening mastic around the edges of the flashing base where it meets the roof.

•Attach a storm collar over the flashing joint to form a water-tight seal. Place non-hardening mastic around the joint, between the storm collar and the vertical pipe.

•Slide the termination cap over the end of the vent pipe and rotate the pipe clockwise 1/4 turn.

HORIZONTAL

OVERHANG

2 FT.

2 FT. MIN.

VERTICAL

MIN.

 

 

WALL

 

 

LOWEST

DISCHARGE

OPENING

TERMINATION

CAP

X

12

ROOF PITCH

IS X/ 12

H (MIN.) - MINIMUM HEIGHT FROM ROOF

TO LOWEST DISCHARGE OPENING

Roof Pitch

H (min.) ft.

flat to 6/12

1.0

6/12 to 7/12

1.25

over 7/12 to 8/12

1.5

over 8/12 to 9/12

2.0

over 9/12 to 10/12

2.5

over 10/12 to 11/12

3.25

over 11/12 to 12/12

4.0

over 12/12 to 14/12

5.0

over 14/12 to 16/12

6.0

over 16/12 to 18/12

7.0

over 18/12 to 20/12

7.5

over 20/12 to 21/12

8.0

Figure 25. Minimum Height from Roof to Lowest Discharge Opening

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Installers Guide What to do if you smell gasSafety and Warning Information Table of Contents Service Parts Standing Pilot Ignition DSI IgnitionBAY-38HV Service Parts List / Liste des pièces de rechange DF-38HV-EPHigh Altitude Installations Installation CodesAppliance Certification CertificationPre-install Preparation Introducing the Heat-N-Glo Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the BAY-38HV Fireplace Dimensions and Locations Constructing the ChaseLocating the Fireplace Clearance RequirementsFraming the Fireplace Vertical and Horizontal Vent RunsPage Installing the Vent System Identifying Vent ComponentsVent System Components and Termination Kits Vent System ApprovalsStraight UP Vertical Venting MAX .4 MStraight OUT Horizontal Venting Venting with ONE 1 90 Elbow Venting withONE 1 90 Elbow Venting with TWO Venting with TWO 2 90 Elbows Venting with three 90 elbows Venting with Three 3 90 ElbowsVenting with Three 3 90 Elbows Installing Vent Components Attach the First Vent Component to the Starting CollarsInstall Support Brackets Hole and Vent PipeHole & New Framing Members Ceiling Firestop Ceiling SideVent Termination Pointing UP=VENT Terminal =AIR Supply Inlet Vent Termination Minimum ClearancesMinimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemsDSI Gas Supply Line Gas Pressure RequirementsTo Check for GAS Leaks Wiring the Fireplace For Standing Pilot Ignition Wiring Appliance RequirementsOptional Accessories Wall SwitchFor Direct Spark Ignition DSI Wiring Appliance Requirements Direct Spark Ignition Wiring DiagramFinishing Sealant MaterialHearth Extensions Installing Trim, Logs, and Ember Material Installing the TrimPositioning the Logs Placing the Ember MaterialAfter the Installation Before Lighting the FireplaceLighting the Fireplace Fireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace

BAY-38HV specifications

The Heat & Glo LifeStyle BAY-38HV is a cutting-edge gas fireplace designed to enhance the ambience of any home while providing efficiency and convenience. This innovative unit combines modern aesthetics with advanced technology, making it a popular choice among homeowners seeking both form and function in their heating solutions.

One of the standout features of the BAY-38HV is its sleek, contemporary design, which allows it to seamlessly integrate into various interior styles. With its clean lines and expansive viewing area, the fireplace creates a focal point in any room, offering a warm and inviting atmosphere. The heat-resistant glass front provides a clear view of the flames, ensuring that the beauty of the fire can be enjoyed from multiple angles.

In terms of technology, the BAY-38HV is equipped with the latest in gas fireplace innovations. It incorporates an advanced IntelliFire ignition system, allowing for easy operation with the simple push of a button. Users can control the flame height and heat output directly from a remote, providing complete convenience and customizability. This makes it an excellent option for those who want to adjust the ambiance of their space effortlessly.

Efficiency is another key characteristic of the BAY-38HV. The fireplace boasts a high efficiency rating, ensuring that the warmth generated is maximized while minimizing energy consumption. This efficient performance not only contributes to a more comfortable home but also helps in reducing heating costs, making it an environmentally friendly choice.

The BAY-38HV also features an array of customizable options, including various log styles and ember bed choices. This allows homeowners to tailor the appearance of their fireplace to suit their individual preferences. Additionally, its compatibility with zone heating systems offers an effective solution for those looking to heat specific areas of their home without relying on central heating.

Safety is paramount with the Heat & Glo LifeStyle BAY-38HV. It includes protective features such as a safety screen and automatic shut-off mechanisms, providing peace of mind for families and individuals.

In summary, the Heat & Glo LifeStyle BAY-38HV gas fireplace is an exemplary model that combines stylish design with advanced technology. Its ease of use, efficiency, customization options, and safety features make it an ideal choice for anyone looking to enhance their living space with the charm and comfort of a gas fireplace.
Top Page Image Contents