Heat & Glo LifeStyle BAY-38HV manual Before Lighting the Fireplace, After the Installation

Page 31

GLASS SPECIFICATIONS:

LARGE

SMALL

GLASS

GLASS

GLASS

TYPE

30 1/8” x 20 5/8”

20 5/8” x 18 3/4”

TEMPERED

Heat-N-Glo fireplaces manufactured with tempered glass may be installed in hazardous locations such as bathtub enclo- sures as defined by the CPSC. The tempered glass has been tested and certified to the requirements of ANSI Z97.1- 1984 and CPSC 16 CFR 1202. (Safety Glazing Certification Council SGCC # 1595 and1597. Architectural Testing, Inc. Reports 02-31919.01 and 02-31917.01.)

This statement is in compliance with SPCS 16 CFR Sec- tion 1201.5 “Certification and labeling requirements” which refers to 15 USC 2063 stating “…Such certificate shall ac- company the product or shall otherwise be furnished to any distributor or retailer to whom the product is delivered.”

Some local building codes require the use of tempered glass with permanent marking in such locations. Glass meeting this requirement is available from the factory. Please con- tact your dealer or distributor to order.

Step 11. Before Lighting the Fireplace

Before lighting the fireplace, be sure to do the following:

Remove all paperwork from underneath the fireplace. Review safety warnings and cautions

•Read the Safety and Warning Information section at the beginning of this Installers Guide.

Double-check for gas leaks

•Before lighting the fireplace, double-check the unit for possible gas leaks.

Double-check vent terminations and front grilles for obstructions.

•Before lighting the fireplace, double-check the unit for possible obstructions that could be blocking the vent ter- minations or the front grilles.

Double-check for faulty components

•Any component that is found to be faulty MUST BE re- placed with an approved component. Tampering with the fireplace components is DANGEROUS and voids all war- ranties.

A small amount of air will be in the gas supply lines. When first lighting the fireplace, it will take a few minutes for the lines to purge themselves of this air. Once the purging is complete, the fireplace will light and will operate normally.

Subsequent lightings of the fireplace will not require this purging of air from the gas supply lines, unless the gas valve has been turned to the OFF position, in which case the air would have to be purged.

NOTE: The fireplace should be run 3 to 4 hours on the initial start-up. Turn it off and let it cool completely. Remove and clean the glass. Replace the glass and run the fireplace for an additional 8 hours. This will help to cure the chemicals used in the paint and logs.

Step 12. Lighting the Fireplace

You’ve reviewed all safety warnings, you’ve checked the fireplace for gas leaks, you know the vent system is unobstructed, and you’ve checked for faulty components. Now you’re ready to light the fireplace.

!WARNING: PLEASE REFER TO THE USER’S MANUAL FOR ALL CAUTIONS, SAFETY, AND

WARNING INFORMATION PERTAINING TO THE LIGHTING AND OPERATION OF THE FIREPLACE.

After the Installation

!LEAVE THIS INSTALLATION MANUAL WITH THE APPLIANCE FOR FUTURE REFERENCE.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents What to do if you smell gas Installers GuideSafety and Warning Information Table of Contents Standing Pilot Ignition DSI Ignition Service PartsDF-38HV-EP BAY-38HV Service Parts List / Liste des pièces de rechangeCertification High Altitude InstallationsInstallation Codes Appliance CertificationIntroducing the Heat-N-Glo Gas Fireplaces Pre-install PreparationANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the BAY-38HV Clearance Requirements Fireplace Dimensions and LocationsConstructing the Chase Locating the FireplaceVertical and Horizontal Vent Runs Framing the FireplacePage Vent System Approvals Installing the Vent SystemIdentifying Vent Components Vent System Components and Termination KitsMAX .4 M Straight UP Vertical VentingStraight OUT Horizontal Venting Venting with Venting with ONE 1 90 ElbowONE 1 90 Elbow Venting with TWO Venting with TWO 2 90 Elbows Venting with Three 3 90 Elbows Venting with three 90 elbowsVenting with Three 3 90 Elbows Attach the First Vent Component to the Starting Collars Installing Vent ComponentsHole and Vent Pipe Install Support BracketsCeiling Firestop Ceiling Side Hole & New Framing MembersPointing UP Vent TerminationVent Termination Minimum Clearances =VENT Terminal =AIR Supply InletMinimum Height from Roof to Lowest Discharge Opening Gas Control Systems Positioning, Leveling, and Securing the FireplaceDSI Gas Pressure Requirements Gas Supply LineTo Check for GAS Leaks Wall Switch Wiring the FireplaceFor Standing Pilot Ignition Wiring Appliance Requirements Optional AccessoriesDirect Spark Ignition Wiring Diagram For Direct Spark Ignition DSI Wiring Appliance RequirementsSealant Material FinishingHearth Extensions Placing the Ember Material Installing Trim, Logs, and Ember MaterialInstalling the Trim Positioning the LogsBefore Lighting the Fireplace After the InstallationLighting the Fireplace Important Turn OFF the GAS Before Servicing Your Fireplace Fireplace Maintenance

BAY-38HV specifications

The Heat & Glo LifeStyle BAY-38HV is a cutting-edge gas fireplace designed to enhance the ambience of any home while providing efficiency and convenience. This innovative unit combines modern aesthetics with advanced technology, making it a popular choice among homeowners seeking both form and function in their heating solutions.

One of the standout features of the BAY-38HV is its sleek, contemporary design, which allows it to seamlessly integrate into various interior styles. With its clean lines and expansive viewing area, the fireplace creates a focal point in any room, offering a warm and inviting atmosphere. The heat-resistant glass front provides a clear view of the flames, ensuring that the beauty of the fire can be enjoyed from multiple angles.

In terms of technology, the BAY-38HV is equipped with the latest in gas fireplace innovations. It incorporates an advanced IntelliFire ignition system, allowing for easy operation with the simple push of a button. Users can control the flame height and heat output directly from a remote, providing complete convenience and customizability. This makes it an excellent option for those who want to adjust the ambiance of their space effortlessly.

Efficiency is another key characteristic of the BAY-38HV. The fireplace boasts a high efficiency rating, ensuring that the warmth generated is maximized while minimizing energy consumption. This efficient performance not only contributes to a more comfortable home but also helps in reducing heating costs, making it an environmentally friendly choice.

The BAY-38HV also features an array of customizable options, including various log styles and ember bed choices. This allows homeowners to tailor the appearance of their fireplace to suit their individual preferences. Additionally, its compatibility with zone heating systems offers an effective solution for those looking to heat specific areas of their home without relying on central heating.

Safety is paramount with the Heat & Glo LifeStyle BAY-38HV. It includes protective features such as a safety screen and automatic shut-off mechanisms, providing peace of mind for families and individuals.

In summary, the Heat & Glo LifeStyle BAY-38HV gas fireplace is an exemplary model that combines stylish design with advanced technology. Its ease of use, efficiency, customization options, and safety features make it an ideal choice for anyone looking to enhance their living space with the charm and comfort of a gas fireplace.
Top Page Image Contents