Heat & Glo LifeStyle EXCLAIM-42T-C Installation of Fireplace, Install the Outside Air Kit

Page 13

4

Installation of Fireplace

 

 

 

 

 

 

 

 

 

 

 

CAUTION

 

WARNING

 

 

 

Fire Risk

 

Sharp Edges

 

 

 

Asphyxiation Risk

 

• Wear protective gloves and safety glasses

 

 

 

Do not draw outside combustion air from:

 

during installation.

 

 

 

• Wall, floor or ceiling cavity.

 

 

 

 

 

 

• Enclosed space such as an attic or

 

 

 

garage.

 

 

 

A. Install the Outside Air Kit

• Close proximity to exhaust vents or

chimneys.

This fireplace will operate correctly only if adequate ventila-

Fumes or odor may result.

tion is provided to allow proper draft to the fireplace system.

 

 

See Section 2.

 

 

 

 

The outside air kit is supplied with this fireplace and its use

 

CAUTION

is highly recommended to minimize the effects of negative

 

 

Risk of Smoke Spillage

pressure within the structure. We recommend you utilize the

shortest duct run to optimize the performance of the outside

Outside air inlet must be located to prevent blockage

air kit. Cold air flow can be minimized by putting a small dip

from:

 

in the duct creating a cold air trap. This trap can also help

•

Leaves

prevent heat build-up and exhausting out the intake due to

•

Snow/ice

the stack effect. The outside air kit inlet should be positioned

•

Other debris

in a manner that will not allow snow, leaves, etc. to block

Blockage may cause combustion air starvation.

the inlet. In some installations the air duct may need to be

 

 

 

 

run vertically. In such an installation, a 3 ft (.914 m) height

 

 

difference must be maintained from the top of the upper-

 

 

most chimney section to the outside combustion air inlet.

 

 

See Figure 4.2.

 

 

See Figure 4.3 for proper placement of outside air inlet.

The outside air kit is installed on the left hand side of the fireplace. See Figure 4.4 for handle location/operation.

 

Flexible Duct

 

 

 

(not supplied)

 

 

Outside Air

 

 

 

Shield

2 Wire Ties

Inlet Ring

 

Figure 4.1 Outside Air Installation

 

 

 

Heat & Glo • EXCLAIM-42C • 4013-094 Rev I • 10/06

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Fire Risk EXCLAIM-42H-C EXCLAIM-42T-CGrate Listing Label Information/LocationNumber Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Getting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Inspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements ¨E. Construct the ChaseInstall the Outside Air Kit Installation of FireplaceSharp Edges Asphyxiation Risk Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Secure the Fireplace Install the RefractoryGrate Brackets Grate Bracket Level the Fireplace Place the Protective Metal Hearth StripsChimney Assembly Height of Chimney Components SL406 SL412 SL418 SL436 SL448 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling firestopsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney In./19 mm in lengthChimney Termination Complete the EnclosureChase Top Install the Termination CapInstalling an ST475 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Hearth Extension FinishingMin 20 in. Min Mantel Finishing MaterialGlass Doors Combustible MaterialGeneral Information Operating InstructionsClear Space Near the Fireplace Outside AirFlue Damper FirescreenWood Fuel GrateStarting a Fire Understanding Vent Problems TroubleshootingDiagnostic Questions Diagnostics and Problem SolvingSolutions fireplace burns the wood too fast. What can I do? Chimney Inspection/Cleaning Maintenance and Servicing the FireplaceDisposal of Ashes Firebox RefractoryWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney ComponentsCatalog # 14-3/4 375 mm Minimum Base Dimensions 26.5 X 28 with 34 X 34 with Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 X20 x Minimum Height InchesService Parts Service Parts EXCLAIM-42-C SeriesRefractory-Herringbone # Description of PartRefractory-Traditional EXCLAIM-42C QtyThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesContact Information

EXCLAIM-42H-C, EXCLAIM-42T-C specifications

The Heat & Glo LifeStyle EXCLAIM-42H-C and EXCLAIM-42T-C are modern gas fireplaces designed to elevate both aesthetics and functionality in residential spaces. With a spacious viewing area and an array of innovative features, these fireplaces create a stunning centerpiece for any room while providing efficient heating and ambiance.

One of the standout characteristics of the EXCLAIM series is its sleek and contemporary design. The 42-inch size of both models makes them suitable for various settings, from cozy living rooms to expansive open-concept spaces. The clean lines and glass front enhance visibility and allow flames to be the focal point, creating a warm and inviting atmosphere.

The technology behind the Heat & Glo LifeStyle EXCLAIM fireplaces includes the advanced IntelliFire® ignition system. This feature offers both convenience and safety, as it eliminates the need for manual lighting and ensures a reliable ignition every time. Users can control the fireplace easily with a remote, smartphone app, or wall switch, allowing for seamless operation and temperature adjustment.

Energy efficiency is a hallmark of the EXCLAIM-42H-C and EXCLAIM-42T-C models. Equipped with a high-efficiency gas burner, these fireplaces provide optimal heat output while minimizing fuel consumption. The option to customize flame intensity and choose from a variety of fire media, including rocks and glass, adds unique personalization to each installation.

Another significant feature is the unique Power Venting system, which offers versatile venting options. This enables homeowners to install the fireplace in non-traditional locations without being limited by conventional venting routes. With a range of venting configurations, the EXCLAIM fireplaces can be adapted to fit various architectural layouts.

The ambient lighting system further enhances the overall visual appeal. Adjustable LED accent lights can illuminate the firebox and highlight the decorative media, allowing users to create a customized ambiance that suits different occasions and moods.

For those concerned about the environmental impact, these fireplaces emphasize clean-burning technology, producing lower emissions compared to traditional wood-burning options. Therefore, homeowners can enjoy the warmth and comfort of a fireplace while being environmentally conscious.

In conclusion, the Heat & Glo LifeStyle EXCLAIM-42H-C and EXCLAIM-42T-C models represent a perfect blend of style, efficiency, and cutting-edge technology. Their contemporary design, convenient operation, and customizable features make them an excellent choice for anyone looking to enhance their living space with a sophisticated gas fireplace.
Top Page Image Contents