Heat & Glo LifeStyle EXCLAIM-42T-C, EXCLAIM-42H-C Secure the Fireplace, Install the Refractory

Page 15

B. Secure the Fireplace

•Position the Fireplace

This fireplace may be placed on either a combustible or noncombustible continuous flat surface. Follow the in- structions for framing in Section 3.D. Slide the fireplace into position. Be sure to provide the minimum air clear- ance at the sides and back of the fireplace assembly. See Section 3.B.

WARNING

Fire Risk!

•Prevent contact with sagging, loose insulation.

•Do NOT install against vapor barriers or exposed insulation.

•Remove smoke shield by removing five screws. See Figure 4.7. Smoke shield is located at top of fireplace front.

•Remove screens by removing screw from the end of each screen rod. See Figure 4.8.

 

Smoke Shield

Front Face

 

Skip

Skip

Remove these screws.

Figure 4.7 Removing Smoke Shield

C. Install the Refractory

We recommend two installers for hearth stone and refrac- tory installation!

•Remove back refractory from outside of fireplace by bending tabs up and lifting refractory out of brackets. See Figure 4.5. Bend tabs back down out of the way. See Figure 4.6. Do not remove screws or brackets from fireplace. If brackets are removed, fill holes in outer shell with screws. Repeat this process to remove side refractories.

•

Figure 4.5 Unpacking Back Refractory

Figure 4.8 Removing the Screen Rods

Remove hearth stone by removing three corrugated shipping spacers (Figure 4.9). Lift hearth stone out of fireplace. See Figure 4.10.

Figure 4.9 Shipping Spacers

Figure 4.6 Bending Refractory Shipping Tabs Back Down

Figure 4.10 Lifting Out the Hearth Stone

Heat & Glo • EXCLAIM-42C • 4013-094 Rev I • 10/06

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Fire Risk EXCLAIM-42H-C EXCLAIM-42T-CListing Label Information/Location GrateNumber Table of Contents Listing and Code Approvals Appliance CertificationNot intended for use as a primary heat source Asphyxiation Risk Design and Installation ConsiderationsGetting Started Negative PressureMarginal Location Typical Fireplace System Tools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesClearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements ¨E. Construct the ChaseRisk of Smoke Spillage Installation of FireplaceInstall the Outside Air Kit Sharp Edges Asphyxiation RiskFt min. from top of uppermost chimney section to air inlet Secure the Fireplace Install the RefractoryGrate Brackets Grate Bracket Level the Fireplace Place the Protective Metal Hearth StripsChimney Assembly Height of Chimney Components SL406 SL412 SL418 SL436 SL448 Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling firestopsIn./19 mm in length Install the Attic Insulation ShieldDouble-check the Chimney Assembly Secure the ChimneyChimney Termination Complete the EnclosureChase Top Install the Termination CapInstalling an ST475 Square Termination Cap Accessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Hearth Extension FinishingMin 20 in. Min Combustible Material Finishing MaterialMantel Glass DoorsGeneral Information Operating InstructionsFirescreen Outside AirClear Space Near the Fireplace Flue DamperWood Fuel GrateStarting a Fire Understanding Vent Problems TroubleshootingDiagnostics and Problem Solving Diagnostic QuestionsSolutions fireplace burns the wood too fast. What can I do? Firebox Refractory Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Disposal of AshesChimney Fire Maintenance Task ListWhen cleaning glass door CleanReference Materials Fireplace DimensionsCatalog # Description Fireplace ComponentsCatalog # Chimney ComponentsCatalog # 14-3/4 375 mm Minimum Height Inches Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 XMinimum Base Dimensions 26.5 X 28 with 34 X 34 with 20 xService Parts Service Parts EXCLAIM-42-C SeriesEXCLAIM-42C Qty # Description of PartRefractory-Herringbone Refractory-TraditionalThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesContact Information

EXCLAIM-42H-C, EXCLAIM-42T-C specifications

The Heat & Glo LifeStyle EXCLAIM-42H-C and EXCLAIM-42T-C are modern gas fireplaces designed to elevate both aesthetics and functionality in residential spaces. With a spacious viewing area and an array of innovative features, these fireplaces create a stunning centerpiece for any room while providing efficient heating and ambiance.

One of the standout characteristics of the EXCLAIM series is its sleek and contemporary design. The 42-inch size of both models makes them suitable for various settings, from cozy living rooms to expansive open-concept spaces. The clean lines and glass front enhance visibility and allow flames to be the focal point, creating a warm and inviting atmosphere.

The technology behind the Heat & Glo LifeStyle EXCLAIM fireplaces includes the advanced IntelliFire® ignition system. This feature offers both convenience and safety, as it eliminates the need for manual lighting and ensures a reliable ignition every time. Users can control the fireplace easily with a remote, smartphone app, or wall switch, allowing for seamless operation and temperature adjustment.

Energy efficiency is a hallmark of the EXCLAIM-42H-C and EXCLAIM-42T-C models. Equipped with a high-efficiency gas burner, these fireplaces provide optimal heat output while minimizing fuel consumption. The option to customize flame intensity and choose from a variety of fire media, including rocks and glass, adds unique personalization to each installation.

Another significant feature is the unique Power Venting system, which offers versatile venting options. This enables homeowners to install the fireplace in non-traditional locations without being limited by conventional venting routes. With a range of venting configurations, the EXCLAIM fireplaces can be adapted to fit various architectural layouts.

The ambient lighting system further enhances the overall visual appeal. Adjustable LED accent lights can illuminate the firebox and highlight the decorative media, allowing users to create a customized ambiance that suits different occasions and moods.

For those concerned about the environmental impact, these fireplaces emphasize clean-burning technology, producing lower emissions compared to traditional wood-burning options. Therefore, homeowners can enjoy the warmth and comfort of a fireplace while being environmentally conscious.

In conclusion, the Heat & Glo LifeStyle EXCLAIM-42H-C and EXCLAIM-42T-C models represent a perfect blend of style, efficiency, and cutting-edge technology. Their contemporary design, convenient operation, and customizable features make them an excellent choice for anyone looking to enhance their living space with a sophisticated gas fireplace.
Top Page Image Contents