Heat & Glo LifeStyle EXCLAIM-42H-C, EXCLAIM-42T-C owner manual Height of Chimney Components

Page 20

A. Chimney Requirements

Vertical distances are measured from the base of the fire- place as shown in Figure 5.2.

 

ft

m

• Minimum overall straight height

18

5.5

• Minimum height with offset/return

18.5

5.6

• Maximum height

90

27.4

• Maximum chimney length between an offset and

20

6

return

 

 

• Maximum distance between chimney stabilizers

35

10.7

• Double offset/return minimum height

24

7.3

• Maximum unsupported chimney length between the

6

1.8

offset and return

 

 

• Maximum straight unsupported chimney height

35

10.7

above the fireplace

 

 

• Maximum unsupported chimney above roof

6

1.8

To determine the chimney components needed to complete your particular installation, follow the steps below:

•Determine the total vertical height of the fireplace installation. This dimension is measured from the base of the fireplace assembly to the point where the smoke exits the termination cap.

•Subtract the effective height of the fireplace assembly from the overall height of the fireplace installation (measured from the base of the fireplace to the bottom of the termination cap).

•Refer to Table 5.1 to determine what components must be selected to complete the fireplace installation.

•Determine the number of ceiling firestops, stabilizers, roof flashing, etc. required to complete the fireplace installation.

Note: A maximum of two pairs of offsets and returns may be used.

WARNING

Fire Risk

•Must maintain 2 in. (51 mm) air clearance to insulation and other combustible materials.

Table 5.1

HEIGHT OF CHIMNEY COMPONENTS

in.

mm

Chimney Stabilizer

 

 

 

SL4

4-3/4

121

Ceiling Firestops

 

 

 

FS538

0

0

 

FS540

0

0

Offsets/Returns

 

 

 

SL430

14-1/2

368

Roof Flashing

 

 

6 ft (1.8 m) max. unsupported run

20 ft (6 m) max. pipe between an offset & return

Ceiling Firestop

71-3/4 in.

(1822 mm)

Effective Height

(bottom of fireplace

to top of starter collar)

6 ft (1.8 m) max. unsupported chimney above roof

35 ft (10.7 m) max. straight unsupported chimney height

18.5ft (5.6 m) min. height/single offset-return 24 ft. (7.3 m) min. height/double offset-return

90 ft (27.4 m) max. height

 

RF570

0

0

 

 

 

 

 

RF571

0

0

Chimney Sections*

 

 

 

SL406

4-3/4

121

 

SL412

10-3/4

273

 

SL418

16-3/4

425

 

 

 

 

 

SL436

34-3/4

883

 

SL448

46-3/4

1187

* Dimensions reflect effective height.

 

 

Figure 5.2 Chimney Requirements

CAUTION

•Do NOT connect this fireplace to a chimney flue servicing another appliance.

•Do NOT connect to any air distribution duct or system.

20

Heat & Glo • EXCLAIM-42C • 4013-094 Rev I • 10/06

Page 19 Page 21
Image 20
Page 19 Page 21
Contents EXCLAIM-42H-C EXCLAIM-42T-C Fire RiskNumber Listing Label Information/LocationGrate Table of Contents Not intended for use as a primary heat source Listing and Code ApprovalsAppliance Certification Design and Installation Considerations Getting StartedNegative Pressure Asphyxiation RiskMarginal Location Typical Fireplace System Fire Risk Explosion Risk Tools and Supplies NeededInspect Fireplace and Components Framing and Clearances Selecting Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the Fireplace¨E. Construct the Chase Chimney RequirementsInstallation of Fireplace Install the Outside Air KitSharp Edges Asphyxiation Risk Risk of Smoke SpillageFt min. from top of uppermost chimney section to air inlet Install the Refractory Secure the FireplaceGrate Brackets Grate Bracket Place the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Height of Chimney Components Using Offsets/Returns SL406 SL412 SL418 SL436 SL448Install the Ceiling firestops Assemble the Chimney SectionsInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney In./19 mm in lengthComplete the Enclosure Chimney TerminationInstall the Termination Cap Chase TopInstalling an ST475 Square Termination Cap Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provisions Finishing Hearth ExtensionMin 20 in. Min Finishing Material MantelGlass Doors Combustible MaterialOperating Instructions General InformationOutside Air Clear Space Near the FireplaceFlue Damper FirescreenGrate Wood FuelStarting a Fire Troubleshooting Understanding Vent ProblemsSolutions Diagnostics and Problem SolvingDiagnostic Questions fireplace burns the wood too fast. What can I do? Maintenance and Servicing the Fireplace Chimney Inspection/CleaningDisposal of Ashes Firebox RefractoryMaintenance Task List When cleaning glass doorClean Chimney FireFireplace Dimensions Reference MaterialsFireplace Components Catalog # DescriptionChimney Components Catalog #Catalog # 14-3/4 375 mm Minimum Base Dimensions 28 X 28 with 32 X 32 with 23 X Minimum Base Dimensions 26.5 X 28 with 34 X 34 with20 x Minimum Height InchesService Parts EXCLAIM-42-C Series Service Parts# Description of Part Refractory-HerringboneRefractory-Traditional EXCLAIM-42C QtyThis page intentionally left blank This page intentionally left blank This page intentionally left blank Warranty For Heat & GLO Fireplaces Limited WarrantyContact Information

EXCLAIM-42H-C, EXCLAIM-42T-C specifications

The Heat & Glo LifeStyle EXCLAIM-42H-C and EXCLAIM-42T-C are modern gas fireplaces designed to elevate both aesthetics and functionality in residential spaces. With a spacious viewing area and an array of innovative features, these fireplaces create a stunning centerpiece for any room while providing efficient heating and ambiance.

One of the standout characteristics of the EXCLAIM series is its sleek and contemporary design. The 42-inch size of both models makes them suitable for various settings, from cozy living rooms to expansive open-concept spaces. The clean lines and glass front enhance visibility and allow flames to be the focal point, creating a warm and inviting atmosphere.

The technology behind the Heat & Glo LifeStyle EXCLAIM fireplaces includes the advanced IntelliFire® ignition system. This feature offers both convenience and safety, as it eliminates the need for manual lighting and ensures a reliable ignition every time. Users can control the fireplace easily with a remote, smartphone app, or wall switch, allowing for seamless operation and temperature adjustment.

Energy efficiency is a hallmark of the EXCLAIM-42H-C and EXCLAIM-42T-C models. Equipped with a high-efficiency gas burner, these fireplaces provide optimal heat output while minimizing fuel consumption. The option to customize flame intensity and choose from a variety of fire media, including rocks and glass, adds unique personalization to each installation.

Another significant feature is the unique Power Venting system, which offers versatile venting options. This enables homeowners to install the fireplace in non-traditional locations without being limited by conventional venting routes. With a range of venting configurations, the EXCLAIM fireplaces can be adapted to fit various architectural layouts.

The ambient lighting system further enhances the overall visual appeal. Adjustable LED accent lights can illuminate the firebox and highlight the decorative media, allowing users to create a customized ambiance that suits different occasions and moods.

For those concerned about the environmental impact, these fireplaces emphasize clean-burning technology, producing lower emissions compared to traditional wood-burning options. Therefore, homeowners can enjoy the warmth and comfort of a fireplace while being environmentally conscious.

In conclusion, the Heat & Glo LifeStyle EXCLAIM-42H-C and EXCLAIM-42T-C models represent a perfect blend of style, efficiency, and cutting-edge technology. Their contemporary design, convenient operation, and customizable features make them an excellent choice for anyone looking to enhance their living space with a sophisticated gas fireplace.
Top Page Image Contents