Heat & Glo LifeStyle Escape-42DV Finishing Materials Requirements, Noncombustible Facing Diagram

Page 46

NON-COMBUSTIBLE

ZONE

43 in.

60 in.

Figure 13.6 Noncombustible Facing Diagram

D. Finishing Materials Requirements

Note: Optional firescreen sits out 1-1/2 inches from the face of the fireplace. When using thin finishing material, you may want to use thicker non-combustible backer board to bring the finishing material flush with the fire screen. This is not required.

•Use the two metal panels shipped with fi replace.

•Unscrew the four screws holding two panels together.

•Slide the two tapered tabs on bottom of each panel into slots of top surround.

•Secure panels with sheet metal screws previously removed from panels.

The metal panels will cover the width of appliance and height of appliance to header board (11-1/2 inch).

•Cover entire face of appliance with non-combustible materials prior to applying finishing material, such as brick, stone or tile. See Figure 9.2, 9.3, 13.6 and 13.7.

•The fi nishing material must NEVER pass the 1/2 inch metal edge around the opening and overhang into the glass opening.

VIEW FROM TOP OF APPLIANCE

 

 

7-1/2 INCH MINIMUM

COMBUSTIBLE OK

 

NON-COMBUSTIBLE

 

MATERIAL

 

 

 

 

FINISH

NON-COMBUSTIBLE

WALL

 

FACING MATERIAL

 

 

 

60 in.

METAL

 

PANELS

 

 

 

 

43 in.

HIGH TEMPERATURE (300º F /149º C MIN.)

 

TOP AND SIDE SEAL JOINTS

 

Figure 13.7 Non-combustible Finishing Material Requirements

46

Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Model What to do if you smell gasCongratulations Homeowner Reference InformationTable of Contents User GuideFinishing Appliance SetupTroubleshooting Reference MaterialsLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Installation of Carbon Monoxide Detectors Requirements for the Commonwealth of MassachusettsOperating Instructions User Guide Gas Fireplace SafetyYour Fireplace Clear Space Fixed Glass AssemblyWall Controls and Wall Switches Decorative Doors and FrontsLighting Instructions IPI Final inspection byFrequently Asked Questions After Fireplace is LitMaintenance and Service Venting Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection LogsBurner Ignition and Operation IPI Pilot Flame PatternsGetting Started Typical Appliance SystemTools and Supplies Needed Design and Installation ConsiderationsInspect Appliance and Components Framing and Clearances Selecting Appliance LocationConstructing the Appliance Chase ClearancesCombustible Mantels Mantel and Wall ProjectionsCombustible Mantel Legs or Wall Projections Hearth Extension Fireplace sitting on combustible surfaceTermination Locations Vent Termination Minimum ClearancesCovered Alcove Applications Porch, deck or balconyVent Table Key Vent Information and DiagramsApproved Pipe Use of ElbowsTwo Elbows Vent Diagrams Top Vent Horizontal Termination One ElbowH1+ H2 Top Vent Horizontal Termination Three Elbows 12 ft V1 + V2 + H1 = 50 ft .2 m Max Top Vent Vertical Termination Three Elbows Ht MaxWall Penetration Framing Vent Clearances and FramingPipe Clearances to Combustibles Combustible Wall PenetrationInstall the Ceiling Firestop Pipe DVPFlat Ceiling Installation Install Attic Insulation ShieldInstalling the Optional Heat-ZoneGas Kit  Vaulted Ceiling InstallationAppliance Preparation Removing Non-combustible Facing Ma- terial AssemblySecuring and Leveling the Appliance Installing Non-combustible Facing Material MaterialAssemble Vent Sections Installing Vent PipeAttach Vent to the Firebox Assembly Assemble Pipe SectionsAssemble Slip Sections Secure the Vent SectionsRotate Seams for Disassembly Disassemble Vent SectionsInstall Metal Roof Flashing Assemble and Install Storm CollarInstall Vertical Termination Cap Heat Shield Requirements for Horizontal TerminationInstall Horizontal Termination Cap DVP-HPC1 DVP-HPC2Gas Pressure Gas InformationFuel Conversion Gas ConnectionIntelliFire Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationDetail a Electrical Service and Repair Junction Box Installation Finishing To install the Splatter GuardSplatter Guard Facing Material Noncombustible Facing Diagram Finishing Materials RequirementsAppliance Setup Install the Log Assembly Log Set Assembly LOGS-ESCAPE42 Models Escape-42DVStep LOG #1 SRV2012-081 Three LOG #2 SRV2012-082 TwoLOG #4 SRV2012-084 LOG #3 SRV2052-083LOG #5 SRV2012-085 LOG #8 SRV2012-088 LOG #6 SRV2052-086LOG #7 SRV2012-087 Final StepAir Shutter Setting Install the MeshAir Shutter Settings Symptom Possible Cause Corrective Action TroubleshootingIntelliFire Ignition System Ues to spark, and main Appliance Dimension Diagram Reference MaterialsVent Components Diagrams DVP-AS2DVP-TRAP1 DVP-TRAP2 DVP-TRAPK1 DVP-TRAPK2 DVP-HPC1 DVP-HPC2 RF6M RF12M 12-1/2 Optional Wire Harness Description Part NumberContact Information

Escape-42DVLP, Escape-42DV specifications

The Heat & Glo LifeStyle Escape-42DV and Escape-42DVLP are innovative direct vent gas fireplaces designed to enhance the ambiance of any living space while providing efficient heating. These models represent the perfect blend of modern technology, aesthetic appeal, and user-friendly features, making them popular choices for homeowners seeking a stylish and functional heating solution.

One of the standout features of the Heat & Glo LifeStyle Escape-42DV is its impressive design. With a large viewing area, the fireplace allows for a mesmerizing display of flames, creating a focal point in any room. The clean, contemporary lines of the unit fit seamlessly into various décor styles, whether modern, traditional, or transitional. Furthermore, the Escape-42DVLP version, designed for those desiring a low-profile option, ensures that homeowners can enjoy the aesthetics of a fireplace without overwhelming the space.

Both models boast advanced technologies that enhance performance and usability. The Direct Vent System allows for efficient combustion by drawing air from outside the home and expelling exhaust gases through a sealed vent. This ensures optimal efficiency and makes them suitable for tight, energy-efficient homes. Additionally, these fireplaces include a Status Light feature that indicates when the fireplace is operating, ensuring peace of mind for users.

The LifeStyle Escape series also excels in customizability. Homeowners can choose from various log sets, decorative media, and tile surrounds, allowing them to tailor their fireplace to match personal styles and preferences. The IntelliFire app provides a convenient way to control the fireplace from a smartphone, featuring options for remote ignition, programmable timers, and flame height adjustments, putting users in complete control of their heating experience.

Safety is paramount, and the Heat & Glo LifeStyle Escape models come equipped with an advanced safety barrier to prevent accidental contact with the hot glass surface, making them family-friendly options. Moreover, their low emissions and high-efficiency ratings contribute to environmentally responsible heating.

In summary, the Heat & Glo LifeStyle Escape-42DV and Escape-42DVLP models combine striking aesthetics, efficient heating technologies, and user-centric features. They offer a modern solution for anyone looking to elevate their home's warmth and sophistication, making them a smart investment for comfort and style.
Top Page Image Contents