Heat & Glo LifeStyle Escape-42DVLP owner manual Appliance Setup

Page 47

14 Appliance Setup

A. Remove Fixed Glass Assembly

See Section 14.G.

B. Remove the Shipping Materials

Remove shipping materials from inside or underneath the fi rebox.

C. Clean the Appliance

Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity.

D. Accessories

Install approved accessories per instructions included with accessories. Contact your dealer for a list of ap- proved accessories.

WARNING! Risk of Fire and Electric Shock! Use ONLY Hearth & Home Technologies-approved optional acces- sories with this appliance. Using non-listed accessories could result in a safety hazard and will void the warranty.

E. Ember Placement

WARNING! Risk of Explosion! Follow ember placement instructions in manual. DO NOT place embers directly over burner ports. Replace ember material annually. Improperly placed embers interfere with proper burner operation.

Ember material is shipped with this gas appliance. To place the ember material:

•Remove the ash lip that is located in front of the glass.

•Remove the side panels located in front of the glass.

•Remove the pull mesh fi rescreen by unhooking from the fi replace.

•Pull and release the six glass latches (3 per side) located on the sides of the glass frame.

•Grasping the upper lip with one hand and the lower lip with the other, pull the bottom of the glass out fi rst. Guide the bottom while letting the top drop down under the top of the opening (see Section 14.G Fixed Glass Assembly).

•There are two types of ember shipped with the unit. Embers for the burner surface and Mystic Embers for the fl oor of the unit.

•Do NOT place embers between log #3 and log #4. They may disrupt the fl ames and are not visible.

•Place Mystic Embers on the fl oor of unit. Use Mystic Embers to hide the pilot wires on left side of the burner.

NOTICE: Do NOT place Mystic Embers over lighted area of lens. Lens may melt if covered.

•Save the remaining ember materials for use during fi replace servicing.

Heat & Glo • Escape-42DV • 2052-900 Rev. Y • 11/11

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents What to do if you smell gas ModelHomeowner Reference Information CongratulationsUser Guide Table of ContentsReference Materials Appliance SetupTroubleshooting FinishingLimited Lifetime Warranty Limited Lifetime WarrantyWarranty Conditions Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Installation of Carbon Monoxide DetectorsYour Fireplace Gas Fireplace SafetyOperating Instructions User Guide Decorative Doors and Fronts Fixed Glass AssemblyWall Controls and Wall Switches Clear SpaceFinal inspection by Lighting Instructions IPIAfter Fireplace is Lit Frequently Asked QuestionsMaintenance and Service Logs Maintenance Tasks-Qualified Service TechnicianGasket Seal and Glass Assembly Inspection VentingIPI Pilot Flame Patterns Burner Ignition and OperationTypical Appliance System Getting StartedInspect Appliance and Components Design and Installation ConsiderationsTools and Supplies Needed Selecting Appliance Location Framing and ClearancesClearances Constructing the Appliance ChaseCombustible Mantel Legs or Wall Projections Mantel and Wall ProjectionsCombustible Mantels Fireplace sitting on combustible surface Hearth ExtensionVent Termination Minimum Clearances Termination LocationsPorch, deck or balcony Covered Alcove ApplicationsUse of Elbows Vent Information and DiagramsApproved Pipe Vent Table KeyH1+ H2 Vent Diagrams Top Vent Horizontal Termination One ElbowTwo Elbows Top Vent Horizontal Termination Three Elbows 12 ft V1 + V2 + H1 = 50 ft .2 m Max Ht Max Top Vent Vertical Termination Three ElbowsCombustible Wall Penetration Vent Clearances and FramingPipe Clearances to Combustibles Wall Penetration FramingPipe DVP Install the Ceiling FirestopVaulted Ceiling Installation Install Attic Insulation ShieldInstalling the Optional Heat-ZoneGas Kit  Flat Ceiling InstallationSecuring and Leveling the Appliance Removing Non-combustible Facing Ma- terial AssemblyAppliance Preparation Material Installing Non-combustible Facing MaterialAssemble Pipe Sections Installing Vent PipeAttach Vent to the Firebox Assembly Assemble Vent SectionsSecure the Vent Sections Assemble Slip SectionsDisassemble Vent Sections Rotate Seams for DisassemblyAssemble and Install Storm Collar Install Metal Roof FlashingHeat Shield Requirements for Horizontal Termination Install Vertical Termination CapDVP-HPC1 DVP-HPC2 Install Horizontal Termination CapGas Connection Gas InformationFuel Conversion Gas PressureElectrical Information Wiring RequirementsOptional Accessories Requirements IntelliFire Ignition System WiringDetail a Electrical Service and Repair Junction Box Installation Splatter Guard To install the Splatter GuardFinishing Facing Material Finishing Materials Requirements Noncombustible Facing DiagramAppliance Setup Step Log Set Assembly LOGS-ESCAPE42 Models Escape-42DVInstall the Log Assembly LOG #2 SRV2012-082 Two LOG #1 SRV2012-081 ThreeLOG #5 SRV2012-085 LOG #3 SRV2052-083LOG #4 SRV2012-084 Final Step LOG #6 SRV2052-086LOG #7 SRV2012-087 LOG #8 SRV2012-088Air Shutter Settings Install the MeshAir Shutter Setting IntelliFire Ignition System TroubleshootingSymptom Possible Cause Corrective Action Ues to spark, and main Reference Materials Appliance Dimension DiagramDVP-AS2 Vent Components DiagramsDVP-TRAP1 DVP-TRAP2 DVP-TRAPK1 DVP-TRAPK2 DVP-HPC1 DVP-HPC2 RF6M RF12M 12-1/2 Description Part Number Optional Wire HarnessContact Information

Escape-42DVLP, Escape-42DV specifications

The Heat & Glo LifeStyle Escape-42DV and Escape-42DVLP are innovative direct vent gas fireplaces designed to enhance the ambiance of any living space while providing efficient heating. These models represent the perfect blend of modern technology, aesthetic appeal, and user-friendly features, making them popular choices for homeowners seeking a stylish and functional heating solution.

One of the standout features of the Heat & Glo LifeStyle Escape-42DV is its impressive design. With a large viewing area, the fireplace allows for a mesmerizing display of flames, creating a focal point in any room. The clean, contemporary lines of the unit fit seamlessly into various décor styles, whether modern, traditional, or transitional. Furthermore, the Escape-42DVLP version, designed for those desiring a low-profile option, ensures that homeowners can enjoy the aesthetics of a fireplace without overwhelming the space.

Both models boast advanced technologies that enhance performance and usability. The Direct Vent System allows for efficient combustion by drawing air from outside the home and expelling exhaust gases through a sealed vent. This ensures optimal efficiency and makes them suitable for tight, energy-efficient homes. Additionally, these fireplaces include a Status Light feature that indicates when the fireplace is operating, ensuring peace of mind for users.

The LifeStyle Escape series also excels in customizability. Homeowners can choose from various log sets, decorative media, and tile surrounds, allowing them to tailor their fireplace to match personal styles and preferences. The IntelliFire app provides a convenient way to control the fireplace from a smartphone, featuring options for remote ignition, programmable timers, and flame height adjustments, putting users in complete control of their heating experience.

Safety is paramount, and the Heat & Glo LifeStyle Escape models come equipped with an advanced safety barrier to prevent accidental contact with the hot glass surface, making them family-friendly options. Moreover, their low emissions and high-efficiency ratings contribute to environmentally responsible heating.

In summary, the Heat & Glo LifeStyle Escape-42DV and Escape-42DVLP models combine striking aesthetics, efficient heating technologies, and user-centric features. They offer a modern solution for anyone looking to elevate their home's warmth and sophistication, making them a smart investment for comfort and style.
Top Page Image Contents