Heat & Glo LifeStyle EM-415 - 36, EM-485T - 42 owner manual Wood Fuel, Hardwood vs Softwood

Page 10

N. Wood Fuel

Hardwood vs Softwood

Your fireplace performance depends on the quality of the firewood you use.

Seasoned wood contains about 8,000 BTUs per pound

.

Hard woods are more dense than soft woods.

Hard woods contain 60% more BTUs than soft woods.

Hard woods require more time to season, burn slower and are harder to ignite.

Soft woods require less time to dry, burn faster and are easier to ignite.

Start the fire with soft wood to bring the fireplace up to operating temperature and to establish draft.

Add hard wood for slow, even heat and longer burn time.

Soft woods

Hard woods

Douglas Fir

Oak

Pine

Maple

Spruce

Apple

Cedar

Birch

Poplar

 

 

Aspen

 

 

Alder

 

 

Moisture

Warning! Risk of Fire!

Do NOT burn wet or green wood.

Wet, unseasoned wood can cause accumulation of creosote.

The majority of the problems fireplace owners experience are caused by trying to burn wet, unseasoned wood.

Wet, unseasoned wood requires energy to evaporate the water instead of heating your home, and

Evaporating moisture cools your chimney, accelerating formation of creosote.

Seasoned Wood

Cut logs to size

Split to 6 in. (152 mm) or less

Air dry to a moisture content of around 20%

-Soft wood - about nine months

-Hard wood - about eighteen months

NoTICE: Seasoning time may vary depending on drying conditions.

Storing Wood

Steps to ensure properly seasoned wood:

Stack wood to allow air to circulate freely around and through woodpile.

Elevate wood pile off ground to allow air circulation underneath.

Smaller pieces of wood dry faster. Any piece over 6 in. (152 mm) in diameter should be split.

Wood (whole or split) should be stacked so both ends of each peice are exposed to air. More drying occurs through the cut ends than the sides.

Store wood under cover to prevent water absorbtion from rain or snow. Avoid covering the sides and ends completely.

Warning! Fire Risk! DO NOT store wood:

In front of the fireplace.

In space required for loading or ash removal.

Processed Solid Fuel Firelogs

Manufactured firelogs may be used with this fireplace. Hearth & Home Technologies Inc. recommends the use of UL Classified processed fuel firelogs. Follow the manufac- turer’s lighting and safety instructions.

Using firelogs may require more frequent chimney inspec- tion and cleaning.

Do not poke or stir the logs while they are burning. Use only firelogs that have been evaluated for the application in manufactured fireplaces and refer to firelog warnings and caution markings on packaging prior to use.

10

Heat & Glo • EM-415, EM-485 • 33056 • Rev AF• 7/12

Image 10
Contents Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceOperation Fire RiskGrate Listing Label Information/LocationNumber Installer Guide Table of ContentsUser Guide Warranty Hearth & Home Technologies Inc Warranty Conditions Non-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodChimney Inspection/Cleaning Maintenance and ServiceDisposal of Ashes Inspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsTools and Supplies Needed Inspect Fireplace and ComponentsFraming & Clearances Fireplace Dimensions .A 1219 mm MinimumConfigurations Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit Junction Box InstallationInstallation of Fan Prepare Junction Box BracketChimney Assembly Maintain minimum height of chimney above roofChimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleInstalling Ceiling Firestops Install Chimney Air KitAssembling Chimney Sections Installing Attic Insulation Shield Prepare Attic Insulation ShieldInstall Flashing Complete InstallationCut out Hole in Roof Chimney Termination Requirements Flat RoofsGas line holes and other openings should be caulked with Chase InstallationsConstruct the Chase Chase should be constructed in the manner of allInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap TCT375 Terra Cotta CapRadiation Shield ShroudsField Constructed Shrouds Mailbox Style Shroud radiation shield required Hearth Extension Finishing= 1/k x inches of thickness Finishing Material Non-combustible FacingCombustible Mantel Grid represents 1 in. scaleGas Log/Lighter Provision AccessoriesInstall Fan Wood Burning InsertsReference Materials Fireplace Components Catalog # Description1321 mm 406 mm Chimney Components Catalog #305 mm 27-3/8 24-5/8 695 mm 625 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 24-5/8 625 mm 787 mmDTO134 a 10-7/8 276 mm Stocked Service PartsIn. Starter Section Assembly 22069B Top Standoff At Depot29992 Traditional Brick Side Refractory Traditional Brick Back Refractory29245 28393 Traditional Brick Hearth RefractoryEM-485T Traditional Refractory Do not Discard this Manual

EM-485T - 42, EM-415 - 36 specifications

Heat & Glo has established itself as a leader in innovative fireplace solutions, and the LifeStyle series, particularly the EM-415 and EM-485T models, showcases the brand's commitment to quality, efficiency, and design flexibility. These gas fireplaces are designed to seamlessly blend into any living space, providing not just warmth but also a stylish focal point.

The EM-415, with its 36-inch firebox, and the EM-485T, featuring a generous 42-inch firebox, deliver a stunning visual experience. Both models boast a contemporary design that enhances the aesthetics of modern homes. The clean, linear appearance is complemented by a large viewing area, allowing for an unobstructed view of the flames.

In terms of technology, Heat & Glo incorporates advanced features such as Intellifireā„¢ Ignition System, which allows for reliable and safe start-up while ensuring energy efficiency. This system also includes the option for remote control operation, providing added convenience for users. The fireplaces can be easily adjusted to suit individual comfort levels, with variable flame settings that allow for customizable heat output.

Additionally, both models utilize the latest in heat management technology. The Heat & Glo LifeStyle series is designed with excellent insulation, promoting better heat retention and minimizing heat loss. This not only enhances the efficiency of the fireplace but also contributes to overall energy savings.

Safety is paramount in the design of the EM-415 and EM-485T. They are equipped with standard safety features such as an automatic shut-off system, ensuring peace of mind while the fireplace is in use.

Moreover, the versatility of these models is highlighted by their ability to be installed in various settings, including walls and corners. The option for different media, such as glass or stone, allows homeowners to personalize their fireplace, making it a perfect fit for any decor style.

Overall, the Heat & Glo LifeStyle EM-415 and EM-485T gas fireplaces represent a fusion of aesthetics, technology, and safety, making them an ideal choice for anyone looking to enhance the comfort and style of their home. With their range of features and design options, these models are sure to create a warm and inviting atmosphere for years to come.