Heat & Glo LifeStyle EM-415 - 36, EM-485T - 42 Chimney Requirements, Height of Chimney Components

Page 26

A. Chimney Requirements

Measure vertical distances from the base of the fireplace as shown in Figure 8.2.

•

Minimum overall straight height

16.5 ft

(5.03 m)

•

Minimum height with offset/return

16.5 ft

(5.03 m)

• Maximum height

90 ft

(27.43 m)

• Maximum chimney length between an offset

20 ft

(6.1 m)

 

and return

 

 

• Maximum distance between chimney

35 ft

(10.67 m)

 

stabilizers

 

 

•

Double offset/return minimum height

20 ft

(6.1 m)

• Maximum unsupported chimney length

6 ft

(1.83 m)

 

between the offset and return

 

 

• Maximum unsupported chimney height above

35 ft

(10.67 m)

 

the fireplace

 

 

• Maximum unsupported chimney above roof

6 ft

(1.83 m)

Warning! Risk of Fire! You must maintain 2 in. (51

mm)air space clearance to insulation and other combus- tible materials around the chimney system. Failure to do so may cause overheating and fire.

Table 8.1

Determine the chimney components needed to complete your particular installation:

•Measure the total vertical height of the fireplace installation from the base of the fireplace assembly to the approximate location of the bottom of the termination cap.

•Subtract the effective height of the fireplace assembly (see Figure 8.2) from the total vertical height to determine the overall height of the chimney installation.

•Create a schematic for your application similar to Figure 8.2 showing components required (referring to Table 8.1). Figure 8.1 identifies those components and where used.

•Install a ceiling firestop whenever the chimney penetrates a floor/ceiling.

Notice: A maximum of two pairs of offsets and returns may be used.

Caution! Risk of Fire and/or Asphyxiation! Do NOT connect this fireplace to a chimney flue servicing another appliance. Do NOT connect to any air distribu- tion duct or system. These actions could cause over- heating/fire in the chimney flue, or release of exhaust fumes into the living areas.

HEIGHT OF CHIMNEY COMPONENTS

in.

mm

Chimney Stabilizer

 

 

 

SL3

4-3/4

121

 

 

 

 

Ceiling Firestops

 

 

 

FS338

0

0

 

FS339

0

0

 

 

 

 

 

FS340

0

0

Offsets/Returns

 

 

 

SL315

13-3/8

340

 

SL330

15-1/2

394

Roof Flashing

 

 

 

RF370

0

0

 

RF371

0

0

 

 

 

 

Chimney Sections*

 

 

20 ft (6.10 m) max. pipe between an offset & return

Ceiling firestop

6 ft (1.83 m) max. unsupported chimney above roof

35 ft (10.7 m) max. straight unsupported chimney height

 

SL306

4-3/4

121

 

SL312

10-3/4

273

 

 

 

 

 

SL318

16-3/4

425

 

SL324

22-3/4

578

 

SL336

34-3/4

883

 

 

 

 

 

SL348

46-3/4

1187

* Dimensions reflect effective height.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

16.5 ft (5.03 m) min. height/single offset-return

41-1/4 in.

 

20 ft. (6.10 m) min. height/double offset-return

(1048 mm)

 

 

 

90 ft (27.4 m) max. height

Effective

 

 

 

 

 

 

 

Height

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 8.2 Chimney Requirements

26

Heat & Glo • EM-415, EM-485 • 33056 • Rev AF• 7/12

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceOperation Fire RiskNumber Listing Label Information/LocationGrate User Guide Table of ContentsInstaller Guide Warranty Hearth & Home Technologies Inc Warranty Conditions Non-Combustible Materials Listing and Code ApprovalsAppliance Certification Combustible MaterialsHot glass will cause burns Operating InstructionsYour Fireplace Grate Seasoned WoodStarting a Fire FirescreenOptional Components Glass DoorsVented Gas Log Sets & Gas Log Lighters Clear SpaceWood Fuel Hardwood vs SoftwoodDisposal of Ashes Maintenance and ServiceChimney Inspection/Cleaning Inspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemNegative Pressure Design and Installation ConsiderationsDraft Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsTools and Supplies Needed Inspect Fireplace and ComponentsFraming & Clearances Fireplace Dimensions .A 1219 mm MinimumConfigurations Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit Junction Box InstallationInstallation of Fan Prepare Junction Box BracketChimney Assembly Maintain minimum height of chimney above roofChimney Requirements Height of Chimney ComponentsUsing Offsets/Returns ExampleAssembling Chimney Sections Install Chimney Air KitInstalling Ceiling Firestops Installing Attic Insulation Shield Prepare Attic Insulation ShieldCut out Hole in Roof Complete InstallationInstall Flashing Chimney Termination Requirements Flat RoofsGas line holes and other openings should be caulked with Chase InstallationsConstruct the Chase Chase should be constructed in the manner of allInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap TCT375 Terra Cotta CapField Constructed Shrouds ShroudsRadiation Shield Mailbox Style Shroud radiation shield required = 1/k x inches of thickness FinishingHearth Extension Finishing Material Non-combustible FacingCombustible Mantel Grid represents 1 in. scaleGas Log/Lighter Provision AccessoriesInstall Fan Wood Burning InsertsReference Materials Fireplace Components Catalog # Description1321 mm 406 mm Chimney Components Catalog #305 mm 27-3/8 24-5/8 695 mm 625 mm Effective Outside Height Diameter 10-1/2 121 mm 267 mm10-1/2 267 mm 305 mm 24-5/8 625 mm 787 mmDTO134 a 10-7/8 276 mm Stocked Service PartsIn. Starter Section Assembly 22069B Top Standoff At Depot29992 Traditional Brick Side Refractory Traditional Brick Back Refractory29245 28393 Traditional Brick Hearth RefractoryEM-485T Traditional Refractory Do not Discard this Manual

EM-485T - 42, EM-415 - 36 specifications

Heat & Glo has established itself as a leader in innovative fireplace solutions, and the LifeStyle series, particularly the EM-415 and EM-485T models, showcases the brand's commitment to quality, efficiency, and design flexibility. These gas fireplaces are designed to seamlessly blend into any living space, providing not just warmth but also a stylish focal point.

The EM-415, with its 36-inch firebox, and the EM-485T, featuring a generous 42-inch firebox, deliver a stunning visual experience. Both models boast a contemporary design that enhances the aesthetics of modern homes. The clean, linear appearance is complemented by a large viewing area, allowing for an unobstructed view of the flames.

In terms of technology, Heat & Glo incorporates advanced features such as Intellifire™ Ignition System, which allows for reliable and safe start-up while ensuring energy efficiency. This system also includes the option for remote control operation, providing added convenience for users. The fireplaces can be easily adjusted to suit individual comfort levels, with variable flame settings that allow for customizable heat output.

Additionally, both models utilize the latest in heat management technology. The Heat & Glo LifeStyle series is designed with excellent insulation, promoting better heat retention and minimizing heat loss. This not only enhances the efficiency of the fireplace but also contributes to overall energy savings.

Safety is paramount in the design of the EM-415 and EM-485T. They are equipped with standard safety features such as an automatic shut-off system, ensuring peace of mind while the fireplace is in use.

Moreover, the versatility of these models is highlighted by their ability to be installed in various settings, including walls and corners. The option for different media, such as glass or stone, allows homeowners to personalize their fireplace, making it a perfect fit for any decor style.

Overall, the Heat & Glo LifeStyle EM-415 and EM-485T gas fireplaces represent a fusion of aesthetics, technology, and safety, making them an ideal choice for anyone looking to enhance the comfort and style of their home. With their range of features and design options, these models are sure to create a warm and inviting atmosphere for years to come.
Top Page Image Contents