Heat & Glo LifeStyle PIER-40 Installation of Fireplace, Things to Consider, Level Fireplace

Page 21

7Installation of Fireplace

Caution! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

A. Things to Consider

•Location of chimney air kit inltet (see Figure 5.1 & 7.4)

•Location of outside air kit

•Electrical connections and/or wall switch

•Gas line piping

B. Position the Fireplace

•Place the fireplace on a continuous flat surface.

•Follow framing instructions in Section 6.

Warning! Risk of Fire! Prevent contact with sag- ging, loose insulation.

•DO NOT install against vapor barriers or exposed insulation.

•Secure insulation and vapor barriers.

•Provide minimum air space clearances at the sides and back of the fireplace assembly as outlined in Section 6.

C. Place Protective Metal Hearth Strips

Warning! Risk of Fire! Protective metal hearth strips MUST be installed. DO NOT cover metal strips with com- bustible materials. Sparks or embers may ignite flooring.

•Refer to Figures 7.1 and 7.2.

•Locate the two protective metal hearth strips measuring approximately 26 in. x 4 in. (660 mm x 102 mm) included with this fireplace.

•Slide each metal strip 2 in. (51 mm) under front edge of fireplace.

•Overlap strips in the middle of fireplace opening by 1 in. (25 mm) minimum..

•Metal strips must extend beyond the front and sides of the fireplace opening by at least 2 in. (51 mm).

•Protect the front of a platform elevated above the hearth extension with metal strips (not included with fireplace) per Figure 7.2. See Section 11 for hearth extension instructions.

D. Level Fireplace

•Level fireplace side-to-side and front-to-back.

•Shim with non-combustible material as necessary.

•Secure fireplace to framing with nailing flanges with a minimum of two fasteners per nailing flange.

•Check fireplace opening for square to ensure proper fit of glass doors. Measure diagonals of fireplace opening to make sure they are equal.

1 in. (25 mm) overlap

Metal strips 2 in. (51 mm) under the edges of the fireplace and must extend beyond the front and side openings by 2 in. (51 mm)

Figure 7.1 Position the Protective Metal Hearth Strips

 

Top piece must overlap

 

bottom piece

 

Raised Platform

2 in.

1 in. (25 mm) min.

(51 mm)

overlap

Floor

2 in.

(51 mm)

Figure 7.2 Protect the Front of an Elevated Platform

Heat & Glo • BAY-40, PIER-40 • 34977 • Rev AB 7/12

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Hot screen/mesh and glass doors will cause burns Fire RiskListing Label Information/Location GrateNumber Model Table of Contents Installer GuideUser Guide Limited Lifetime Warranty Warranty Hearth & Home Technologies IncThis warranty is void if Warranty ConditionsAppliance Certification Listing and Code ApprovalsNon-Combustible Materials Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Starting a Fire Seasoned WoodGrate FirescreenOutside Air optional Glass DoorsOptional Components Vented Gas Log Sets & Gas Log LightersWood Fuel Chimney Inspection/Cleaning Maintenance and ServiceDisposal of Ashes Creosote Formation and Need for RemovalCheck Firebox Refractory Glass CleaningInspect Grate Frequency As desiredStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDesign and Installation Considerations DraftNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Select Fireplace Location Framing & ClearancesAir Space Clearances ClearancesSidewalls/Surrounds Frame the FireplaceThings to Consider Installation of FireplacePosition the Fireplace Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit AK17 Installation BAY-40AK14/AK18 Installation PIER-40 Chimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling Firestops330 mm Install Attic Insulation ShieldInstall Flashing Complete InstallationFollowing steps should be skipped if using a chase Cut out Hole in RoofFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Radiation Shield ShroudsField Constructed Shrouds Open Top Shroud TR11/TR11T caps require radiation shieldRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield requiredFinishing Hearth Extension= 1/k x inches of thickness 1575 mm Hearth Refractory In. Micore or equivilent insulation Finishing MaterialSidewalls/Surrounds Combustible MantelGas Log/Lighter Provision AccessoriesWood Burning Inserts Gas Code, Ansi Z223.1Reference Materials Fireplace Dimensions13 mm Catalog # Description Chimney Components15-1/4 387 mm 483 mm 15-5/8 397 mm BAY-40 Service PartsStocked At DepotComments PIER-40 Service PartsPart number list on following Part number list on followingPier-40 Do not Discard this Manual

PIER-40 specifications

The Heat & Glo LifeStyle PIER-40 is a modern gas fireplace designed to enhance any living space while providing superior heating performance. This unit is known for its sleek and contemporary design, making it a popular choice among homeowners and interior designers alike. With its large viewing area, the PIER-40 offers an inviting ambiance that draws people in and creates a warm, cozy atmosphere.

One of the standout features of the PIER-40 is its advanced heating technology. It is equipped with a powerful heater that efficiently distributes warmth throughout the room, ensuring comfortable temperatures even during the coldest months. The adjustable flame height allows users to customize the ambiance, with the option to set the flames to low for a gentle glow or higher for a more robust fire.

Another significant characteristic of the PIER-40 is its versatile design options. Available in various finishes and styles, it can easily complement any decor. The unit can be installed in different configurations, including built-in or as a stand-alone fireplace, providing flexibility in design and placement. The option for glass media instead of traditional logs further adds to its modern appeal.

The LifeStyle series from Heat & Glo emphasizes efficiency and ease of use. The PIER-40 features an intuitive remote control system, allowing users to operate the fireplace from anywhere in the room. This convenience is coupled with an adjustable fan system that helps distribute heat evenly and quickly.

Furthermore, the PIER-40 is built with safety in mind. It includes a safety screen, which minimizes the risk of accidental burns, and features an automatic shut-off mechanism that activates in case of gas leaks or other safety concerns.

In terms of energy efficiency, the PIER-40 is designed to produce a significant amount of heat with minimal gas consumption, making it an eco-friendly option for those looking to reduce their carbon footprint. Overall, the Heat & Glo LifeStyle PIER-40 is a perfect blend of style, technology, and safety, making it an ideal heating solution for modern homes. Its combination of aesthetic appeal, advanced features, and robust performance ensures that it will be a focal point in any room while keeping you warm and comfortable year-round.
Top Page Image Contents