Heat & Glo LifeStyle PIER-40 Design and Installation Considerations, Draft, Negative Pressure

Page 15

B. Design and Installation Considerations

Notice: Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction over restrictions, installation inspection and permits.

Before installing, determine the following:

•Where the fireplace is to be installed

•The vent system configuration to be used

•Gas supply piping

•Electrical wiring

•Framing and finishing details

•Whether optional accessories—devices such as a fan, wall switch or remote control­—are desired

Notice: Junction box should be installed during initial setup to avoid major reconstruction.

C. Draft

Draft is the pressure difference needed to vent fireplaces successfully. When a fireplace is drafting successfully, all combustion byproducts are exiting the home through the chimney.

Considerations for successful draft include:

•Preventing negative pressure

•Location of fireplace and chimney

NoTICE: Hearth & Home Technologies assumes no responsibility for the improper performance of the fireplace system caused by:

•Inadequate draft due to environmental conditions

•Downdrafts

•Tight sealing construction of the structure

•Mechanical exhausting devices

•Improper location of the chimney

D. Negative Pressure

Warning! Risk of Asphyxiation! Negative pressure can cause spillage of combustion fumes and soot. Fire must draft properly for safe operation.

Negative pressure results from the imbalance of air avail- able for the fireplace to operate properly. It can be stron- gest in lower levels of the house.

Causes include:

•Exhaust fans (kitchen, bath, etc.)

•Range hoods

•Combustion air requirements for furnaces, water heaters and other combustion appliances

•Clothes dryers

•Location of return-air vents to furnace or air conditioning

•Imbalances of the HVAC air handling system

•Upper level air leaks such as:

-Recessed lighting

-Attic hatch

-Duct leaks

To minimize the effects of negative air pressure:

•Install the outside air kit with the intake facing prevailing winds during the heating season

•Ensure adequate outdoor air for all combustion appliances and exhaust equipment

•Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace

•Avoid installing the fireplace near doors, walkways or small isolated spaces

•Recessed lighting should be a “sealed can” design

•Attic hatches weather stripped or sealed

•Attic mounted duct work and air handler joints and seams taped or sealed

•Basement installations should be avoided

NoTICE: Hearth & Home Technologies Inc. recommends the use of direct vent fireplaces in basements.

Heat & Glo • BAY-40, PIER-40 • 34977 • Rev AB 7/12

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Hot screen/mesh and glass doors will cause burns Fire RiskListing Label Information/Location GrateNumber Model Table of Contents Installer GuideUser Guide Limited Lifetime Warranty Warranty Hearth & Home Technologies IncThis warranty is void if Warranty ConditionsCombustible Materials Listing and Code ApprovalsAppliance Certification Non-Combustible MaterialsOperating Instructions Your FireplaceHot glass will cause burns Firescreen Seasoned WoodStarting a Fire GrateVented Gas Log Sets & Gas Log Lighters Glass DoorsOutside Air optional Optional ComponentsWood Fuel Creosote Formation and Need for Removal Maintenance and ServiceChimney Inspection/Cleaning Disposal of AshesFrequency As desired Glass CleaningCheck Firebox Refractory Inspect GrateStart Fire Problems Possible Cause Solution Troubleshooting GuideTypical Fireplace System Getting StartedDesign and Installation Considerations DraftNegative Pressure Frequently open doors Central heat outlets or returns Locating Fireplace & ChimneyTools and Supplies Needed Fireplace System RequirementsInspect Fireplace and Components Select Fireplace Location Framing & ClearancesAir Space Clearances ClearancesSidewalls/Surrounds Frame the FireplacePlace Protective Metal Hearth Strips Installation of FireplaceThings to Consider Position the FireplaceFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit AK17 Installation BAY-40AK14/AK18 Installation PIER-40 Chimney Assembly Height of Chimney Components Chimney RequirementsExample Using Offsets/ReturnsAssemble Chimney Sections Install Chimney Air KitInstalling the Ceiling Firestop Install Ceiling Firestops330 mm Install Attic Insulation ShieldCut out Hole in Roof Complete InstallationInstall Flashing Following steps should be skipped if using a chaseFlat Roofs Chimney Termination RequirementsConstruct the Chase Chase InstallationsInstall Chase Top Install Fireplace & ChimneyST1175 Square Termination Cap Install Termination CapTCT1175 Terra Cotta Cap Open Top Shroud TR11/TR11T caps require radiation shield ShroudsRadiation Shield Field Constructed ShroudsRoofed Style Shroud radiation shield required Mailbox Style Shroud radiation shield requiredFinishing Hearth Extension= 1/k x inches of thickness 1575 mm Hearth Refractory In. Micore or equivilent insulation Finishing MaterialSidewalls/Surrounds Combustible MantelGas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provision Wood Burning InsertsReference Materials Fireplace Dimensions13 mm Catalog # Description Chimney Components15-1/4 387 mm 483 mm 15-5/8 397 mm BAY-40 Service PartsStocked At DepotComments Part number list on following Service PartsPIER-40 Part number list on followingPier-40 Do not Discard this Manual

PIER-40 specifications

The Heat & Glo LifeStyle PIER-40 is a modern gas fireplace designed to enhance any living space while providing superior heating performance. This unit is known for its sleek and contemporary design, making it a popular choice among homeowners and interior designers alike. With its large viewing area, the PIER-40 offers an inviting ambiance that draws people in and creates a warm, cozy atmosphere.

One of the standout features of the PIER-40 is its advanced heating technology. It is equipped with a powerful heater that efficiently distributes warmth throughout the room, ensuring comfortable temperatures even during the coldest months. The adjustable flame height allows users to customize the ambiance, with the option to set the flames to low for a gentle glow or higher for a more robust fire.

Another significant characteristic of the PIER-40 is its versatile design options. Available in various finishes and styles, it can easily complement any decor. The unit can be installed in different configurations, including built-in or as a stand-alone fireplace, providing flexibility in design and placement. The option for glass media instead of traditional logs further adds to its modern appeal.

The LifeStyle series from Heat & Glo emphasizes efficiency and ease of use. The PIER-40 features an intuitive remote control system, allowing users to operate the fireplace from anywhere in the room. This convenience is coupled with an adjustable fan system that helps distribute heat evenly and quickly.

Furthermore, the PIER-40 is built with safety in mind. It includes a safety screen, which minimizes the risk of accidental burns, and features an automatic shut-off mechanism that activates in case of gas leaks or other safety concerns.

In terms of energy efficiency, the PIER-40 is designed to produce a significant amount of heat with minimal gas consumption, making it an eco-friendly option for those looking to reduce their carbon footprint. Overall, the Heat & Glo LifeStyle PIER-40 is a perfect blend of style, technology, and safety, making it an ideal heating solution for modern homes. Its combination of aesthetic appeal, advanced features, and robust performance ensures that it will be a focal point in any room while keeping you warm and comfortable year-round.
Top Page Image Contents