Heat & Glo LifeStyle Montana-36, Montana-42 owner manual Grate, Wood Fuel

Page 27

G. Grate

The factory installed integral grate must be used to hold the logs from falling out of an open fireplace and to allow air to pass between the burning logs. It is important to keep the fire off the hearth and to allow the ashes to collect beneath the fire, thereby forming a layer of additional heat protection.

WARNING

Fire Risk

Use only factory installed integral grate. May cause overfire.

H.Wood Fuel

Firewood

Your fireplace performance depends on the quality of the firewood you use. All seasoned wood, regardless of spe- cies, contains about 8,000 BTU’s per pound, and hard- woods have a greater density than soft woods. A piece of hardwood will contain about 60% more BTU’s than an equal size piece of soft wood. Firewood is commonly sold by the cord (128 cu. ft.). A cord of seasoned oak (hardwood) would contain about 60% more potential en- ergy than a cord of seasoned pine (soft wood).

Examples of soft wood trees are Douglas fir, pine, spruce, and cedar, poplar, aspen and alder. Soft woods require less time to dry, burn faster and are easier to ignite than hardwoods.

Examples of hardwood trees are oak, maple, apple, and birch. Hardwoods require more time to season, burn slower and are usually harder to ignite than soft woods.

The best wood fuel is a combination of soft wood and hardwood. Start the fire with soft wood; the fire will give off quick heat to bring the fireplace up to operating tem- perature, and then the hardwood can be added for slow, even heat and longer burn time.

Moisture

Regardless of which species of wood you burn, the single most important factor that effects the way your fireplace operates is the amount of moisture in the wood. The ma- jority of the problems fireplace owners experience are caused by trying to burn wet, unseasoned wood.

Freshly cut wood can be as much water as it is wood, having a moisture content of around 50%. Imagine a wooden bucket that weighs about eight pounds. Fill it with a gallon of water, put it in the fireplace and try to burn it. This sounds ridiculous but that is exactly what you are doing if you burn unseasoned wood.

Seasoning

Seasoned firewood is nothing more than wood that is cut to size, split and air dried to a moisture content of around 20%. The time it takes to season wood varies from around nine months for soft woods to as long as eighteen months for hardwoods. The key to seasoning wood is to be sure it has been split, exposing the wet interior and increasing the surface area of each piece. A tree that was cut down a year ago and not split is likely to have almost as high a moisture content now as it did when it was cut.

The following guideline will ensure properly seasoned wood:

Stack the wood to allow air to circulate freely around and through the woodpile.

Elevate the woodpile off the ground to allow air circulation underneath.

The smaller the pieces, the faster the drying process. Any piece over 6 in. (152 mm) in diameter should be split.

Cover the top of the woodpile for protection from rain and snow. Avoid covering the sides and ends completely. Doing so may trap moisture from the ground and impede air circulation.

The problems with burning wet, unseasoned wood are twofold: First, you will receive less heat output from wet wood because it requires energy in the form of heat to evaporate the water trapped inside. This is wasted ener- gy that should be used for heating your home. Secondly, this moisture evaporates in the form of steam which has a cooling effect in your fireplace and chimney system. When combined with tar and other organic vapors from burning wood it will form creosote which condenses in the relatively cool fireplace and chimney.

WARNING

Fire Risk

Do NOT burn wet or green wood.

Store wood in dry location.

Stack wood so both ends are exposed to air.

Wet, unseasoned wood can cause accumulation of creosote.

WARNING

Fire Risk

Do NOT store wood:

Closer than required clearances to combustibles to fireplace.

Within space required for loading or ash removal.

Heat & Glo LifeStyles Collection • Montana • 4039-150 Rev I • 08/06

27

Image 27
Contents Fire Risk Models Montana-36 Montana-42 Woodburning FireplaceListing Label Information/Location GrateNumber Table of Contents Listing and Code Approvals Appliance CertificationNot intended for use as a primary heat source Design and Installation Considerations Getting StartedMoisture Resistance Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Exterior Walls see Figure Freestanding Installations see FigureFraming and Clearances Selecting Fireplace LocationFreestanding Installation Clearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Installation of Fireplace Install the Dual Cooling Air KitFire Risk Sharp Edges Asphyxiation Risk Position the Fireplace Secure the FireplaceHeight of Chimney Components Chimney Assembly¨ Table Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Chimney Termination Complete the EnclosureChase Top Install the Termination CapInstalling an ST1175 Square Termination Cap Accessories Gas Log/Lighter ProvisionsGas Code, Ansi Z223.1 Finishing Hearth ExtensionHearth Extension Insulation Alternatives, R Value = Finishing Material MantelGlass Doors General Information Operating InstructionsFirescreen Outside AirClear Space Near the Fireplace Flue DamperWood Fuel GrateStarting a Fire Diagnostics and Problem Solving TroubleshootingFirebox Refractory Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Disposal of AshesChimney Fire Maintenance Task ListWhen cleaning glass door CleanReference Materials Fireplace DimensionsDescription Fireplace ComponentsCatalog # Chimney Components432 mm 13-3/8 340 mm 51 mm Woodburning Termination Cap Montana Series Service PartsHerringbone refractory available post week 3/04 Description of PartThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesContact Information

Montana-42, Montana-36 specifications

The Heat & Glo LifeStyle Montana-42 and Montana-36 gas fireplaces represent a notable fusion of modern design and advanced technology, catering to homeowners seeking both functionality and aesthetic appeal. These two models are part of the LifeStyle series, crafted to enhance living spaces while offering efficient heating solutions.

One of the most striking features of the Montana series is its contemporary design. Both models boast large viewing areas framed by sleek lines, allowing for an unobstructed view of the beautiful flames. The Montana-42, with its 42-inch width, provides a larger fire display, creating a dramatic focal point in any room. The Montana-36, while slightly smaller, still offers a captivating fire view that can effortlessly enhance a space's ambiance.

In terms of technology, these fireplaces are equipped with Heat & Glo’s innovative IntelliFire™ ignitions system. This advanced ignition technology ensures reliable and safe startup with minimal effort. Homeowners appreciate the convenience of remote control operation, enabling them to adjust flame height and heat output to suit their preferences without leaving their seats.

Efficiency is a cornerstone of the Montana series. Both models are designed to maximize heat output while minimizing fuel consumption. With high-efficiency ratings, they not only provide warmth but also contribute to the overall energy savings in the home. This is particularly beneficial in colder climates where heating can significantly increase energy costs.

Another noteworthy feature of the Montana fireplaces is the customizable aesthetics. Consumers can choose from a range of liner options, media types, and decorative fronts to create a personalized look that fits their unique style. The ability to tailor the fireplace to individual tastes ensures that it becomes a seamless fit within any interior design scheme.

Moreover, the Montana-42 and Montana-36 are designed with ease of installation in mind, offering installation flexibility that accommodates various spaces and building requirements. The sealed combustion system enhances safety by drawing air from outside for combustion, preventing the depletion of indoor air.

In conclusion, the Heat & Glo LifeStyle Montana-42 and Montana-36 gas fireplaces are exemplary choices for homeowners seeking a blend of efficiency, modern design, and customizable features. With advanced technology that promotes ease of use and energy efficiency, these models stand out as significant additions to contemporary living spaces. Whether you opt for the larger Montana-42 or the slightly more compact Montana-36, both fireplaces promise to deliver warmth and aesthetic charm that enhances the comfort of your home.