Heat & Glo LifeStyle Montana-36, Montana-42 Complete the Enclosure, Chimney Termination

Page 19

6 Complete the Enclosure

A. Chimney Termination

Chimney Termination Requirements

Must have a cap approved and listed for this fireplace system

Must not be located where it will become plugged by snow or other material

Must terminate at least 3 ft (914 mm) above the roof and at least 2 ft (610 mm) above any portion of the roof within 10 ft (3.05 m),

Must be located away from trees or other structures

Mark the Exit Point of the Roof

Locate the point where the chimney will exit the roof by plumbing down to the center of the chimney. Drive a nail up through the roof to mark the center. See Figure 6.1.

Cut Out the Hole in the Roof

Measure to either side of the nail and mark the 14-1/2 in. x 14-1/2 in. (368 mm x 368 mm) opening required. This is measured on the horizontal; actual length may be larg- er depending on the pitch of the roof. Cut out and frame the opening. See Chapter 25 of the Uniform Building Code for roof framing details.

Assemble the Chimney Sections Through the Roof

Continue to add chimney sections through the roof open- ing, maintaining at least a 2 in. (51 mm) air space to com- bustible materials.

Install the Roof Flashing

WARNING

Fire Risk

Must maintain 2 in. air (51 mm) clearance to insulation and other combustible materials.

Figure 6.1 Ceiling/Attic Construction

If a roof flashing is to be used, install the roof flashing appropriate to the roof pitch and install a round termination cap and storm collar following the instructions shipped with the cap.

Install the Chimney Air Kit (required in Canada):

When installing the chimney air kit, follow the instructions provided with this accessory.

Heat & Glo LifeStyles Collection • Montana • 4039-150 Rev I • 08/06

19

Image 19
Contents Fire Risk Models Montana-36 Montana-42 Woodburning FireplaceGrate Listing Label Information/LocationNumber Table of Contents Appliance Certification Listing and Code ApprovalsNot intended for use as a primary heat source Getting Started Design and Installation ConsiderationsMoisture Resistance Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Exterior Walls see Figure Freestanding Installations see FigureFraming and Clearances Selecting Fireplace LocationFreestanding Installation Clearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Install the Dual Cooling Air Kit Installation of FireplaceFire Risk Sharp Edges Asphyxiation Risk Position the Fireplace Secure the FireplaceHeight of Chimney Components Chimney Assembly¨ Table Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Chimney Termination Complete the EnclosureChase Top Install the Termination CapInstalling an ST1175 Square Termination Cap Gas Log/Lighter Provisions AccessoriesGas Code, Ansi Z223.1 Hearth Extension FinishingHearth Extension Insulation Alternatives, R Value = Mantel Finishing MaterialGlass Doors General Information Operating InstructionsFirescreen Outside AirClear Space Near the Fireplace Flue DamperWood Fuel GrateStarting a Fire Diagnostics and Problem Solving TroubleshootingFirebox Refractory Maintenance and Servicing the FireplaceChimney Inspection/Cleaning Disposal of AshesChimney Fire Maintenance Task ListWhen cleaning glass door CleanReference Materials Fireplace DimensionsDescription Fireplace ComponentsCatalog # Chimney Components432 mm 13-3/8 340 mm 51 mm Woodburning Termination Cap Montana Series Service PartsHerringbone refractory available post week 3/04 Description of PartThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesContact Information

Montana-42, Montana-36 specifications

The Heat & Glo LifeStyle Montana-42 and Montana-36 gas fireplaces represent a notable fusion of modern design and advanced technology, catering to homeowners seeking both functionality and aesthetic appeal. These two models are part of the LifeStyle series, crafted to enhance living spaces while offering efficient heating solutions.

One of the most striking features of the Montana series is its contemporary design. Both models boast large viewing areas framed by sleek lines, allowing for an unobstructed view of the beautiful flames. The Montana-42, with its 42-inch width, provides a larger fire display, creating a dramatic focal point in any room. The Montana-36, while slightly smaller, still offers a captivating fire view that can effortlessly enhance a space's ambiance.

In terms of technology, these fireplaces are equipped with Heat & Glo’s innovative IntelliFire™ ignitions system. This advanced ignition technology ensures reliable and safe startup with minimal effort. Homeowners appreciate the convenience of remote control operation, enabling them to adjust flame height and heat output to suit their preferences without leaving their seats.

Efficiency is a cornerstone of the Montana series. Both models are designed to maximize heat output while minimizing fuel consumption. With high-efficiency ratings, they not only provide warmth but also contribute to the overall energy savings in the home. This is particularly beneficial in colder climates where heating can significantly increase energy costs.

Another noteworthy feature of the Montana fireplaces is the customizable aesthetics. Consumers can choose from a range of liner options, media types, and decorative fronts to create a personalized look that fits their unique style. The ability to tailor the fireplace to individual tastes ensures that it becomes a seamless fit within any interior design scheme.

Moreover, the Montana-42 and Montana-36 are designed with ease of installation in mind, offering installation flexibility that accommodates various spaces and building requirements. The sealed combustion system enhances safety by drawing air from outside for combustion, preventing the depletion of indoor air.

In conclusion, the Heat & Glo LifeStyle Montana-42 and Montana-36 gas fireplaces are exemplary choices for homeowners seeking a blend of efficiency, modern design, and customizable features. With advanced technology that promotes ease of use and energy efficiency, these models stand out as significant additions to contemporary living spaces. Whether you opt for the larger Montana-42 or the slightly more compact Montana-36, both fireplaces promise to deliver warmth and aesthetic charm that enhances the comfort of your home.