Heat & Glo LifeStyle Montana-36 Getting Started, Design and Installation Considerations

Page 5

2 Getting Started

A. Design and Installation Considerations

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.

When planning a fireplace installation, it is necessary to de- termine the following information before installing:

•Where the fireplace is to be installed. See Sections 3 and 4.

•The vent system configuration to be used. See Sections 5 and 6.

•Framing and finishing details. See Sections 3, 6 and 8.

•Whether optional accessories are desired. See Section 12.

Draft is the pressure difference needed to vent fireplaces successfully. Considerations for successful draft include:

•Location of fireplace and chimney

Moisture Resistance:

This outdoor fireplace will shed moderate amounts of water, but is not waterproof. Water and condensing water vapor may enter the chase under certain conditions.

The fireplace will not perform as an exterior wall. Moisture penetration must be considered for construction that places the fireplace in structure walls or on moisture sensitive sur- faces.

When installed on exterior walls: Hearth & Home Tech- nologies recommends that the fireplace chase be con- structed outside the structure’s weather envelope. Where the platform meets the wall, use a flashing detail similar to that required for attached decks. Chase platforms, including hearths should slope away from the structure at 1/8 in. to 1/4 in. per foot. The fireplace can be shimmed level.

When installed on surfaces where water may collect or cause damage: Hearth & Home Technologies recommends that a drainage pan be placed under the unit. This can be constructed of metal, adhesive polymer membrane (such as ice and water shield) or other suitable materials. A means of drainage out of the pan such as tubes or weep holes should be provided. A slope of 1/8 in. to 1/4 in. per foot towards the drain port is suggested. The fireplace can be shimmed level.

Hearths should slope away from the front of the fireplace and chase at 1/8 in. to 1/4 in. per foot. Spark strips must be on top of any combustible hearth materials used for moisture management.

Heat & Glo LifeStyles Collection • Montana • 4039-150 Rev I • 08/06

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Fire Risk Models Montana-36 Montana-42 Woodburning FireplaceNumber Listing Label Information/LocationGrate Table of Contents Not intended for use as a primary heat source Listing and Code ApprovalsAppliance Certification Moisture Resistance Design and Installation ConsiderationsGetting Started Typical Fireplace System Typical Fireplace SystemFire Risk Explosion Risk Tools and Supplies NeededInspect Fireplace and Components Framing and Clearances Freestanding Installations see FigureSelecting Fireplace Location Exterior Walls see FigureFreestanding Installation Clearances to Combustible Materials ClearancesFrame the Fireplace Sidewalls/SurroundsChimney Requirements Fire Risk Sharp Edges Asphyxiation Risk Installation of FireplaceInstall the Dual Cooling Air Kit Position the Fireplace Secure the FireplaceHeight of Chimney Components Chimney Assembly¨ Table Using Offsets/ReturnsAssemble the Chimney Sections Install the Ceiling FirestopsSecure the Chimney Install the Attic Insulation ShieldDouble-check the Chimney Assembly Chimney Termination Complete the EnclosureChase Top Install the Termination CapInstalling an ST1175 Square Termination Cap Gas Code, Ansi Z223.1 AccessoriesGas Log/Lighter Provisions Hearth Extension Insulation Alternatives, R Value = FinishingHearth Extension Glass Doors Finishing MaterialMantel General Information Operating InstructionsClear Space Near the Fireplace Outside AirFlue Damper FirescreenWood Fuel GrateStarting a Fire Diagnostics and Problem Solving TroubleshootingChimney Inspection/Cleaning Maintenance and Servicing the FireplaceDisposal of Ashes Firebox RefractoryWhen cleaning glass door Maintenance Task ListClean Chimney FireReference Materials Fireplace DimensionsDescription Fireplace ComponentsCatalog # Chimney Components432 mm 13-3/8 340 mm 51 mm Woodburning Termination Cap Montana Series Service PartsHerringbone refractory available post week 3/04 Description of PartThis page intentionally left blank This page intentionally left blank This page intentionally left blank Limited Warranty Warranty For Heat & GLO FireplacesContact Information

Montana-42, Montana-36 specifications

The Heat & Glo LifeStyle Montana-42 and Montana-36 gas fireplaces represent a notable fusion of modern design and advanced technology, catering to homeowners seeking both functionality and aesthetic appeal. These two models are part of the LifeStyle series, crafted to enhance living spaces while offering efficient heating solutions.

One of the most striking features of the Montana series is its contemporary design. Both models boast large viewing areas framed by sleek lines, allowing for an unobstructed view of the beautiful flames. The Montana-42, with its 42-inch width, provides a larger fire display, creating a dramatic focal point in any room. The Montana-36, while slightly smaller, still offers a captivating fire view that can effortlessly enhance a space's ambiance.

In terms of technology, these fireplaces are equipped with Heat & Glo’s innovative IntelliFire™ ignitions system. This advanced ignition technology ensures reliable and safe startup with minimal effort. Homeowners appreciate the convenience of remote control operation, enabling them to adjust flame height and heat output to suit their preferences without leaving their seats.

Efficiency is a cornerstone of the Montana series. Both models are designed to maximize heat output while minimizing fuel consumption. With high-efficiency ratings, they not only provide warmth but also contribute to the overall energy savings in the home. This is particularly beneficial in colder climates where heating can significantly increase energy costs.

Another noteworthy feature of the Montana fireplaces is the customizable aesthetics. Consumers can choose from a range of liner options, media types, and decorative fronts to create a personalized look that fits their unique style. The ability to tailor the fireplace to individual tastes ensures that it becomes a seamless fit within any interior design scheme.

Moreover, the Montana-42 and Montana-36 are designed with ease of installation in mind, offering installation flexibility that accommodates various spaces and building requirements. The sealed combustion system enhances safety by drawing air from outside for combustion, preventing the depletion of indoor air.

In conclusion, the Heat & Glo LifeStyle Montana-42 and Montana-36 gas fireplaces are exemplary choices for homeowners seeking a blend of efficiency, modern design, and customizable features. With advanced technology that promotes ease of use and energy efficiency, these models stand out as significant additions to contemporary living spaces. Whether you opt for the larger Montana-42 or the slightly more compact Montana-36, both fireplaces promise to deliver warmth and aesthetic charm that enhances the comfort of your home.
Top Page Image Contents