Installation for Vertical Termination

VENTING INSTALLATION INSTRUCTIONS

VENTING INSTALLATION INSTRUCTIONS

Continued

INSTALLATION FOR VERTICAL TERMINATION

Note: Vertical restrictor must be installed in all vertical installations.

1.Determine the route your vertical venting will take. If ceiling joists, roof rafters, or other framing will obstruct the venting system, consider an offset (see Figure 19) to avoid cutting load bearing members. Note: Pay special attention to these instal- lation instructions for required clearances (air space) to com- bustibles when passing through ceilings, walls, roofs, enclo- sures, attic rafters, etc. Do not pack air spaces with insulation. Also note maximum vertical rise of the venting system and any maximum horizontal offset limitations.

2.Set the fireplace in desired location. Drop a plumb line down from the ceiling to the position of the fireplace exit flue. Mark the center point where the vent will penetrate the ceiling. Drill a small locating hole at this point.

Drop a plumb line from the inside of the roof to the locating hole in the ceiling. Mark the center point where the vent will penetrate the roof. Drill a small locating hole at this point.

Roof Flashing

Wall Strap

45° Elbow

Ceiling Firestop

Figure 19 - Offset with Wall Strap and 45° Elbows

Flat Ceiling Installation

1.Cut a 10 3/4" square hole in the ceiling using the locating hole as a center point. The opening should be framed to 10 3/4"x10 3/4" (273 mm x 273 mm) inside dimensions, as shown in Figure 9 on page 8 using framing lumber the same size as the ceiling joists. If the area above the ceiling is an insulated ceiling or a room, nail firestop from the top side. This prevents loose insula- tion from falling into the required clearance space. Otherwise, install firestop below the framed hole. The firestop should be installed with no less than three nails per side (see Figure 20).

2.Assemble the desired lengths of pipe and elbows necessary to reach from the fireplace flue up through the firestop. Be sure all pipe and elbow connections are fully twist-locked (see Fig- ure 8, page 8).

3.Cut a hole in the roof using the locating hole as a center point. (Cover any exposed open vent pipes before cutting hole in roof.) The 10 3/4"x10 3/4" hole must be measured on the horizontal; actual length may be larger depending on the pitch of the roof. There must be a 1" clearance from the vent pipe to combustible materials. Frame the opening as shown in Figure 9, page 8.

4.Connect a section of pipe and extend up through the hole.

Note: If an offset is needed to avoid obstructions, you must support the vent pipe every 3 feet. Use wall straps for this purpose (see Figure 19). Whenever possible, use 45° elbows instead of 90° elbows. The 45° elbow offers less restriction to the flow of the flue gases and intake air.

5.Place the flashing over the pipe section(s) extending through the roof. Secure the base of the flashing to the roof and fram- ing with roofing nails. Be sure roofing material overlaps the top edge of the flashing as shown in Figure 19. There must be a 1" clearance from the vent pipe to combustible materials.

6.Continue to add pipe sections until the height of the vent cap meets the minimum building code requirements described in Figure 7 on page 6. Note: You must increase vent height for steep roof pitches. Nearby trees, adjoining rooflines, steep pitched roofs, and other similar factors may cause poor draft or down-drafting in high winds. Increasing the vent height may solve this problem.

7.Twist-lock the vent cap onto the last section of vent pipe.

Note: If the vent pipe passes through any occupied areas above the first floor, including storage spaces and closets, you must enclose pipe. You may frame and sheetrock the enclosure with standard construction material. Make sure and meet the minimum allowable clearances to combustibles. Do not fill any of the required air spaces with insulation.

If area above is a room, install	If area above is not a room, install
firestop above framed hole.	firestop below framed hole.

Figure 20 - Installing Firestop

For morevisit www..com

111253-01E

VV36EPC1 specifications

Desa VV36EPC1 is a state-of-the-art compact village generator known for its robust performance and reliability in various applications. As a versatile energy solution, it is particularly well-suited for remote areas, outdoor events, and emergency backup systems.

One of the main features of the VV36EPC1 is its superior power output, providing up to 36 kVA, making it capable of handling significant electrical loads. This generator is equipped with a powerful diesel engine that ensures efficient fuel consumption while delivering consistent power generation. The engine is designed to operate quietly, minimizing noise pollution, which is essential for residential or community use.

The VV36EPC1 incorporates advanced technology for energy management and safety. The digital control panel presents real-time data on voltage, frequency, and operating hours, allowing users to monitor performance easily. Additionally, it features an automatic voltage regulator (AVR) that stabilizes voltage output, preventing equipment damage caused by fluctuations.

Another standout characteristic of the VV36EPC1 is its rugged build quality. Constructed with durable materials, this generator is designed to withstand harsh environmental conditions. Its weather-resistant enclosure protects internal components from rain and dust, ensuring longevity and reliability during operation.

Portability is also a significant advantage of the VV36EPC1. It includes built-in wheels and a convenient lifting handle, making it easy to transport across various terrains. This feature makes it an excellent choice for construction sites, catering, or festivals, where mobility is essential.

In terms of safety, the VV36EPC1 offers multiple safeguards, including low oil shutdown and overload protection. These features ensure the generator operates safely, automatically shutting down when oil levels are low or if the load exceeds its capacity.

In summary, the Desa VV36EPC1 is a powerful, reliable, and portable generator, equipped with advanced monitoring technology and essential safety features. Whether for recreational purposes or critical power supply needs, the VV36EPC1 stands out as an optimal choice for diverse applications, providing peace of mind with its dependable performance and durability.