Desa (V)V42EPA(1), (V)V42ENA(1) installation manual Venting Installation Instructions, Continued

Page 9
Manual background

VENTING INSTALLATION INSTRUCTIONS

Installation Planning (Cont.)

9

VENTING INSTALLATION INSTRUCTIONS

Continued

Manual background WARNING: Do not recess vent termination into any wall. This will cause a fire hazard.

6.Noncombustible Exterior Wall: Position the horizontal vent cap in the center of the 8 1/2" round hole and attach to the exte- rior wall with four wood screws provided. Before attaching the vent cap to exterior wall, run a bead of non-hardening mastic (pliable sealant) around the outside edges to make a seal be- tween it and the outside wall. Note: The four wood screws provided should be replaced with appropriate fasteners for stucco, brick, concrete, or other types of sidings.

Combustible Exterior Wall: For vinyl siding, stucco, or wood exteriors, a siding standoff must be installed between the vent cap and exterior wall. The siding standoff prevents excessive heat from damaging the siding materials. Siding material must be cut to accommodate standoff. Bolt the vent cap to the stand- off. Apply non-hardening mastic around outside edge of stand- off. Position the standoff/cap assembly in the center of the 10 3/4" square hole and attach to exterior wall with wood screws provided (see Figure 11). The siding standoff must sit flush against the exterior fascia material.

7.Combustible Exterior Wall Only: Slide the wall firestop over the vent pipe before connecting horizontal run to vent cap (see Figure 12).

8.Carefully move fireplace, with vent assembly attached, toward wall and insert vent pipe into horizontal termination. The pipe overlap should be a minimum of 11/4".

9.Combustible Exterior Wall Only: Slide wall firestop against interior wall surface and attach with screws provided (see Figure 12). See Figure 13 for horizontal termination details.

Apply Mastic to

All Four Sides

Vent Cap

Wood Screw

Figure 10 - Installing Horizontal Vent Cap (Noncombustible Exterior)

Cut Siding Away to Fit Standoff

Standoff

Wood Screw

Vent Cap

Screws

Apply Mastic

to All Four Sides

Figure 11 - Installing Siding Standoff (Combustible Exterior)

Interior Wall

Manual backgroundSurface

Wall

Manual background Firestop

Vent Cap

Horizontal

(Horizontal

Vent Pipe

Termination)

 

Screw

Figure 12 - Connecting Vent Cap with Horizontal Vent Pipe

Manual backgroundFor moreManual backgroundManual backgroundManual backgroundvisit www.Manual backgroundManual backgroundManual background.comManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background

111907-01A

Image 9
Contents FOR YOUR SAFETY OWNER’S OPERATION AND INSTALLATION MANUALFOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS Do not touch any electrical switchTABLE OF CONTENTS SAFETY INFORMATIONWARNINGS LOCAL CODES PRODUCT IDENTIFICATIONContinued SAFETY INFORMATIONPRODUCT FEATURES PRE-INSTALLATION PREPARATIONLOCATION AND SPACE REQUIREMENTS FRAMING AND FINISHING CLEARANCESPRE-INSTALLATION PREPARATION ContinuedD E B L LOCATION OF TERMINATION CAPV G V A LOCATION OF TERMINATION CAPINSTALLATION PRECAUTIONS VENTING INSTALLATION INSTRUCTIONSHorizontal Termination Installation INSTALLATION PLANNINGVENTING INSTALLATION INSTRUCTIONS ContinuedVENTING INSTALLATION INSTRUCTIONS VENTING INSTALLATION INSTRUCTIONSContinued VENTING INSTALLATION INSTRUCTIONS Horizontal Termination ConfigurationsVENTING INSTALLATION INSTRUCTIONS ContinuedVENTING INSTALLATION INSTRUCTIONS ContinuedRecommended Applications Continued VENTING INSTALLATION INSTRUCTIONSVenting with Two 90 Elbows Venting with Two 90 ElbowsFlat Ceiling Installation INSTALLATION FOR VERTICAL TERMINATIONVENTING INSTALLATION INSTRUCTIONS ContinuedVENTING INSTALLATION INSTRUCTIONS Vertical Termination ConfigurationsContinued Venting with Two 90 ElbowsVENTING INSTALLATION INSTRUCTIONS HIGH ALTITUDE INSTALLATIONContinued Vertical VentingINSTALLING OPTIONAL BLOWER ACCESSORY FIREPLACE INSTALLATIONDESA Venting Accessories Model BK InstallationFIREPLACE INSTALLATION 8.Plug in blower power cordContinued Blower Wiring Diagram Model BKT InstallationFIREPLACE INSTALLATION ContinuedINSTALLING GAS PIPING TO FIREPLACE LOCATION FIREPLACE INSTALLATIONContinued Installation Items Needed CONNECTING FIREPLACE TO GAS SUPPLYPressure Testing Gas Supply Piping System CHECKING GAS CONNECTIONSCleaning Glass Door Pressure Testing Fireplace Gas ConnectionsSee Cleaning and Maintenance on page REMOVING/REPLACING GLASS DOORINSTALLING LOGS, LAVA ROCK AND GLOWING EMBERS FIREPLACE INSTALLATIONContinued FIREPLACE INSTALLATION FIREPLACE INSTALLATIONFigure 41- Installing Log No Figure 44 - Installing Log NoWALL SWITCH INSTALLATION WIRING DIAGRAMOPTIONAL REMOTE CONTROL INSTALLATION Model WRC FIREPLACE INSTALLATIONOPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCEPILOT ASSEMBLY OPERATING OPTIONAL BLOWER ACCESSORYINSPECTING BURNERS BURNER FLAME PATTERNGLASS DOOR CLEANING AND MAINTENANCEPILOT AND BURNERS LOGSOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYing Gas Connections, pages 20 and REMEDYTROUBLESHOOTING OBSERVED PROBLEMMODELS ILLUSTRATED PARTS BREAKDOWNILLUSTRATED PARTS BREAKDOWN Models VV42ENA1, VV42ENSA1, VV42ENHA1PARTS LIST PARTS LISTBURNER ASSEMBLY FOR MODELS VV42ENA1, VV42ENSA1 VV42ENHA1, VV42EPA1,3 VV42EPSA1, AND VV42EPHA1ILLUSTRATED PARTS BREAKDOWN PARTS LIST PARTS LISTPART NUMBERSERVICE HINTS REPLACEMENT PARTSTECHNICAL SERVICE SPECIFICATIONSOWNERS REGISTRATION FORM TAPE Postage RequiredTAPE FLEXIBLE GAS LINE CONNECTOR - GA5081 ACCESSORIESREMOTE CONTROL KIT - WRC SERIES Not Shown WALL MOUNTED ON/OFF SWITCH - GWMS2 Not ShownLIMITED WARRANTY DIRECT-VENTFIREPLACE NOT A UPCWARRANTY INFORMATION