Desa (V)V42EPA(1) Removing/Replacing Glass Door, Pressure Testing Fireplace Gas Connections

Page 21
Pressure Testing Fireplace Gas Connections

FIREPLACE INSTALLATION

Checking Gas Connections (Cont.) Removing/Replacing Glass Door

21

FIREPLACE INSTALLATION

Continued

Pressure Testing Fireplace Gas Connections

1.Open equipment shutoff valve (see Figure 33, page 20).

2.Open propane/LP supply tank valve for propane/LP fireplace or main gas valve located on or near gas meter for natural gas fireplace.

3.Make sure control knob of fireplace is in the OFF position.

4.Check all joints from equipment shutoff valve to gas valve (see Figure 34 for propane/LP or Figure 35 for natural gas, page 20). Apply noncorrosive leak detection fluid to all joints. Bubbles forming show a leak. Correct all leaks at once.

5.Light fireplace (see Operating Fireplace, pages 25 and 26). Check all other internal joints for leaks.

6.Turn off fireplace (see To Turn Off Gas to Appliance, page 25).

REMOVING/REPLACING GLASS DOOR

REMOVING/REPLACING GLASS DOOR CAUTION: Do not operate this fireplace with a broken glass door panel or without the glass door panel securely in place. For replacement part infor- mation see Replacement Parts, page 34.

Removing Louver Panels CAUTION: Wear gloves and safety glasses while handling or removing broken glass. Do not remove if glass is hot. Keep children and pets away from glass.

Removing Glass Door WARNING: If fireplace has been running, turn off and unplug fireplace. Let cool before removing glass door or louvers.

Removing Louver Panels

Remove the top and bottom louver panels by simultaneously pulling both top end spring latches towards the center of the appliance until they are disengaged from the locating holes (see Figure 36). Repeat for bottom spring latches and pull the louvers outward. To install or replace items removed, simply reverse the procedures above.

Removing Glass Door

If replacement of glass is necessary, the entire assembly, glass and frame, must be replaced. If glass is broken, wear gloves and tape the remaining fragments onto the frame.

1.Remove screen assembly by pushing the rod either left or right and then down and forward to remove screen/rod assembly from the firebox. Set assembly aside.

2.Lift up on latches to unlock. There are two on top of firebox and two below firebox that hold glass door in place (see Figure 37).

3.While holding glass door to prevent it from falling and caus- ing injury, remove the five screws from the hinge located on the left side of door frame assembly (see Figure 37).

4.Remount the new frame at the hinge with five new screws before closing door. This will ensure seating of the gasket.

5.Close glass door frame. Lock latches by placing the bar under the tab on door and pushing down and back on latch (see Figure 37).

6.Replace screen/rod assembly by reversing step 1.

7.Replace louvers by reversing procedure under Removing Lou- ver Panels.

Latch

Unlock

Lock

Hinge

Screw

Glass

Frame

Assembly

Figure 37 - Removing/Replacing Glass Door

Cleaning Glass Door

See Cleaning and Maintenance on page 27.

Cleaning Glass Door Spring Latch

Louver Panel

Figure 36 - Removing Louver Panel

See Cleaning and Maintenance on page 27.For moreManual backgroundManual backgroundManual backgroundvisit www.Manual backgroundManual backgroundManual background.comManual backgroundManual backgroundManual backgroundManual backgroundManual backgroundManual background

111907-01A

Image 21
Contents FOR YOUR SAFETY OWNER’S OPERATION AND INSTALLATION MANUALFOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS Do not touch any electrical switchTABLE OF CONTENTS SAFETY INFORMATIONWARNINGS LOCAL CODES PRODUCT IDENTIFICATIONContinued SAFETY INFORMATIONPRODUCT FEATURES PRE-INSTALLATION PREPARATIONLOCATION AND SPACE REQUIREMENTS FRAMING AND FINISHING CLEARANCESPRE-INSTALLATION PREPARATION ContinuedD E B L LOCATION OF TERMINATION CAPV G V A LOCATION OF TERMINATION CAPINSTALLATION PRECAUTIONS VENTING INSTALLATION INSTRUCTIONSHorizontal Termination Installation INSTALLATION PLANNINGVENTING INSTALLATION INSTRUCTIONS ContinuedVENTING INSTALLATION INSTRUCTIONS VENTING INSTALLATION INSTRUCTIONSContinued VENTING INSTALLATION INSTRUCTIONS Horizontal Termination ConfigurationsVENTING INSTALLATION INSTRUCTIONS ContinuedVENTING INSTALLATION INSTRUCTIONS ContinuedRecommended Applications Continued VENTING INSTALLATION INSTRUCTIONSVenting with Two 90 Elbows Venting with Two 90 ElbowsFlat Ceiling Installation INSTALLATION FOR VERTICAL TERMINATIONVENTING INSTALLATION INSTRUCTIONS ContinuedVENTING INSTALLATION INSTRUCTIONS Vertical Termination ConfigurationsContinued Venting with Two 90 ElbowsVENTING INSTALLATION INSTRUCTIONS HIGH ALTITUDE INSTALLATIONContinued Vertical VentingINSTALLING OPTIONAL BLOWER ACCESSORY FIREPLACE INSTALLATIONDESA Venting Accessories Model BK InstallationFIREPLACE INSTALLATION 8.Plug in blower power cordContinued Blower Wiring Diagram Model BKT InstallationFIREPLACE INSTALLATION ContinuedINSTALLING GAS PIPING TO FIREPLACE LOCATION FIREPLACE INSTALLATIONContinued Installation Items Needed CONNECTING FIREPLACE TO GAS SUPPLYPressure Testing Gas Supply Piping System CHECKING GAS CONNECTIONSCleaning Glass Door Pressure Testing Fireplace Gas ConnectionsSee Cleaning and Maintenance on page REMOVING/REPLACING GLASS DOORINSTALLING LOGS, LAVA ROCK AND GLOWING EMBERS FIREPLACE INSTALLATIONContinued FIREPLACE INSTALLATION FIREPLACE INSTALLATIONFigure 41- Installing Log No Figure 44 - Installing Log NoWALL SWITCH INSTALLATION WIRING DIAGRAMOPTIONAL REMOTE CONTROL INSTALLATION Model WRC FIREPLACE INSTALLATIONOPERATING FIREPLACE FOR YOUR SAFETY READ BEFORE LIGHTINGLIGHTING INSTRUCTIONS TO TURN OFF GAS TO APPLIANCEPILOT ASSEMBLY OPERATING OPTIONAL BLOWER ACCESSORYINSPECTING BURNERS BURNER FLAME PATTERNGLASS DOOR CLEANING AND MAINTENANCEPILOT AND BURNERS LOGSOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYing Gas Connections, pages 20 and REMEDYTROUBLESHOOTING OBSERVED PROBLEMMODELS ILLUSTRATED PARTS BREAKDOWNILLUSTRATED PARTS BREAKDOWN Models VV42ENA1, VV42ENSA1, VV42ENHA1PARTS LIST PARTS LISTBURNER ASSEMBLY FOR MODELS VV42ENA1, VV42ENSA1 VV42ENHA1, VV42EPA1,3 VV42EPSA1, AND VV42EPHA1ILLUSTRATED PARTS BREAKDOWN PARTS LIST PARTS LISTPART NUMBERSERVICE HINTS REPLACEMENT PARTSTECHNICAL SERVICE SPECIFICATIONSOWNERS REGISTRATION FORM TAPE Postage RequiredTAPE FLEXIBLE GAS LINE CONNECTOR - GA5081 ACCESSORIESREMOTE CONTROL KIT - WRC SERIES Not Shown WALL MOUNTED ON/OFF SWITCH - GWMS2 Not ShownLIMITED WARRANTY DIRECT-VENTFIREPLACE NOT A UPCWARRANTY INFORMATION