Desa (V)T36P SERIES, (V)T32P, CHDV32NR Vertical Termination Configurations, Vertical Venting

Page 13

Venting Installation

instructions

Continued

Vertical Termination Configurations

Figures 21 through 24 show four different configurations for verti- cal termination.

Venting with Two 90° Elbows

Vertical (V)	Horizontal (H1) +
	Horizontal (H2)
5' min.	2' max.
6' min.	4' max.
7' min.	6' max.
8' min.	8' max.
20' max.	8' max.

45° Elbow

Venting with Two 90° Elbows

Vertical (V1)	Horizontal (H)
5' min.	6' max.
6' min.	12' max.
7' min.	18' max.
8' min.	20' max.

Note: Install restrictor into inner collar of

fireplace as shown.

45° Elbow

Note: Vertical (V1) + Vertical (V2) = 40' max.

Figure 23 - Vertical Venting Configuration Using Two 90° Elbows (Vertical Round High Wind Termination Shown)

Note: Install restrictor into inner collar of fireplace as shown.

Figure 21 - Vertical Venting Configuration Using Two 90°

Elbows with Two Horizontal Runs (Vertical Round High Wind

Termination Shown)

	Venting with One 90° Elbow
	Vertical (V)	Horizontal (H)
	5' min.	2' max.
	6' min.	4' max.
	7' min.	6' max.
	8' min.	8' max.
45° Elbow	20' max.	8' max.

45° Elbow

Note: Install restrictor into inner collar of fireplace as shown.

Vertical Venting

V = 40' max.

Note: Install restrictor into inner collar of fireplace as shown.

Figure 22 - Vertical Venting Configuration Using One 90°	Figure 24 - Vertical Venting Configuration With No Horizontal
Elbow (Vertical Round High Wind Termination Shown)	Run (Vertical Round High Wind Termination Shown)

108661-01F

www.desatech.com

13

Image 13

Contents What to do if YOU Smell GAS For Your SafetySafety Information Table of ContentsProduct Identification Local Codes Product FeaturesLocation and space requirements Pre-Installation PreparationClearances 23 1 Framing and finishingTermination CAP AIR Supply Inlet GAS Meter Location of Termination CapInstallation Precautions Venting Installation InstructionsInstallation Planning Horizontal Termination InstallationVent Pipe Connections Installing Siding Standoff Square Termination Horizontal Termination ConfigurationsVenting with Two 90 Elbows Snorkel Termination InstallationOffset with Wall Strap and 45 Elbows Flat Ceiling InstallationVertical Venting Vertical Termination ConfigurationsHigh Altitude Installation Fireplace InstallationParts lists for venting kits and components Installing optional blower accessoriesBlower Model BK Model BKT InstallationBlower Wiring Diagram Installing Gas Piping to Fireplace LocationInstallation Items Needed Installation Items Needed Connecting Fireplace to GAS SupplyPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaAttaching Alkaline Battery to Receiver Installing Remote ReceiverRemoving/Replacing Glass Door Cleaning Glass DoorRemoving Louver Panels Removing Glass DoorInstalling Log No Installing logs, lava rock and glowing embersInstalling Logs No and No Manual Lighting Procedure For your safety read Before lightingOperating Fireplace Lighting InstructionsRemote Operation OpTIONAL Hand-HeldThermostat Series Model HRC200 On/Off Series Model HRC100Pilot assembly Operating optional blower accessoryInspecting Burners Operating optional GWMT1 Wall Mounted ThermostatGlass Door Cleaning MaintenancePilot and burners LogsTo clean pilot. This can damage pilot unit TroubleshootingTroubleshooting Above Gas leak. See Warning statementService Hints Replacement PartsTechnical Service SpecificationsAccessories CHDV32NR Illustrated Parts BreakdownParts List CTDV36NR Parts List Keep this Warrant Warranty Information