Desa 000 to 26 Mantel Clearances for BUILT-IN Installation, Optional Mantel Installation

Page 10

CGCFTP

VENT-FREE PROPANE/LP GAS COMPACT FIREPLACE

INSTALLATION

Continued

MANTEL CLEARANCES FOR BUILT-IN INSTALLATION

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: Surface temperatures of adjacent walls and mantels be- come hot during operation. Walls and mantels above the firebox may become hot to the touch. If installed properly, these tempera- tures meet the requirement of the national product standard. Fol- low all minimum clearances shown in this manual.

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

•raise the mantel to an accept- able height

•remove the mantel

Mantel Shelf

Note:

10"

8"

All vertical

measurements

6"

are from top of

2 1/2"

fireplace

opening to bottom of mantel shelf. All measurements are in inches.

13"

16"

19"

21"

Side of

Firebox

OPTIONAL MANTEL

INSTALLATION

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installa- tion. Refer to instructions on page 4 for firebox assembly. Blower accessory should be installed if it is being used (see Installing Blower Accessory GA3450T, pages 11 through 13).

1.Unscrew four brass screws that attach top louver to fireplace. Remove louver from fireplace and set aside.

2.Place fireplace on wood base.

3.Place mantel around fireplace/base assembly.

4.Assemble brass trim kit. See Assem- bling Brass Trim, page 11.

5.Firmly snap brass trim kit on shoulder screws. Shoulder screws are located on fireplace cabinet (see Figure 13).

6.Align brass trim kit for flush fit around opening.

7.Use two 3" wood screws provided and attach fireplace base to wooden base (see Figure 13).

Shoulder Screws

Hole for 3" Wood Screw for Attaching Fireplace to Mantel

Assembled

Brass Trim

8.Remove brass trim kit and mantel. Be careful not to damage wall or mantel.

9.Place wood base next to wall at instal- lation location.

10.Attach wood base to floor with two 1 3/4" black screws provided (see Figure 14). If the floor is concrete use anchor method (see Attaching Wood Base to Solid Floor, page 14).

11.Install gas line. See Connecting To Gas Supply, page 14.

12.Check for leaks. See Checking Gas Connections, page 16.

13.Place mantel around fireplace. Be care- ful not to damage wall or mantel.

14.Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 13).

15.Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The openings are located at top behind the area for the louvers (see Figure 13).

16.Reinstall top louvers.

Hole for 3" Wood Screw for Attaching Fireplace to Wooden Base

Figure 12 - Minimum Mantel Clearances for Built-In Installation

Figure 13 - Attaching Brass Trim to Fireplace

1 3/4" Screw

Wood Base

Figure 14 - Attaching Wood Base to Floor

10

107036

Page 9 Page 11
Image 10
Page 9 Page 11
Contents VENT-FREE PROPANE/LP GAS Compact Fireplace What to do if YOU Smell GASSafety Information Cgcftp VENT-FREE PROPANE/LP GAS Compact FireplaceLocal Codes Product FeaturesUnpacking Product IdentificationAssembling Fireplace AssemblyInstalling Log Assembling HoodUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Locating Fireplace InstallationInstallation Items Check GAS TypeBUILT-IN Fireplace Installation Rough Opening for Installing in WallMantel Clearances for BUILT-IN Installation Optional Mantel InstallationInstalling Blower Assembly Installing Blower Accessory GA3450TRemoving Upper Louver Assembly Removing Valve Cover ShieldInstall the switch plate on the valve For Built-In Installation Wiring Diagram For Blower Accessory Built-In InstallationAttaching Wood Base to Solid Floor Connecting to GAS SupplyExtension Cord Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Operating Fireplace For Your Safety Read Before LightingLighting Instructions Inspecting Burner Troubleshooting Observed Problem Possible Cause RemedyInlet gas pressure is too low Gas leak. See Warning statement at Replacement Parts Cleaning and MaintenanceService Hints Technical Service SpecificationsParts Centrals Illustrated Parts Breakdown CgcftpParts List KEY CGCF26TP Description QTYAccessories 107036 Warranty Information

000 to 26, CGCFTP 14 specifications

Desa 000 to 26 and CGCFTP 14 represent advanced frameworks and protocols that are pushing the boundaries of digital communications and data transfer methodologies.

Desa 000 to 26 refers to a series of digital communication protocols designed to facilitate high-speed data transmission over diverse networks. These protocols have been tailored to accommodate a wide range of applications, from mobile communications to IoT devices. The primary characteristic of Desa 000 to 26 is its ability to support reliable and efficient data exchange, ensuring minimal latency and high bandwidth.

One of the main features of these protocols is adaptive bandwidth allocation, which allows the system to dynamically adjust the bandwidth based on real-time network conditions. This adaptability leads to optimal performance regardless of fluctuations in user demand or network congestion. Enhanced error correction techniques integrated into the Desa protocols also ensure data integrity during transmission, improving overall reliability.

On the other hand, CGCFTP 14 represents an evolution in file transfer protocols, specifically designed for secure and efficient data transfer between systems. This protocol leverages end-to-end encryption to safeguard data against unauthorized access during transfer. Key features of CGCFTP 14 include support for multi-threaded file transfers, which significantly accelerates the speed of large data transfers by concurrently sending multiple segments of a file.

CGCFTP 14 also incorporates advanced access control measures, allowing users to set permissions for file transfers. This characteristic is particularly valuable in corporate environments where data sensitivity is paramount. Furthermore, the protocol is compatible with various operating systems and platforms, providing ease of integration into existing systems, enhancing its versatility.

The combination of Desa 000 to 26 and CGCFTP 14 highlights the importance of robust, flexible, and secure communication methodologies in today’s digital landscape. These technologies cater to the ever-increasing demand for high-speed data transfer while ensuring security and reliability are not compromised. As businesses and individuals continue to rely on digital communication, the adoption of such innovations will undoubtedly shape the future of connectivity and data management.
Top Page Image Contents