Desa CGCFTP 14, 000 to 26 Troubleshooting, Observed Problem Possible Cause Remedy

Page 19

OWNER’S MANUAL

TROUBLESHOOTING

Note: For additional help, visit DESA International’s technical service web site at www.desatech.com.

Note: All troubleshooting items are listed in order of operation.

WARNING: Turn off and un- plug fireplace and let cool before servicing. Only a qualified ser- vice person should service and repair fireplace.

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no

1.

Ignitor cable pinched or wet

1.

Free ignitor cable if pinched by any

spark at ODS/pilot

 

 

 

metal or tubing. Keep ignitor cable dry

 

2.

Ignitor electrode not connected to igni-

2.

Reconnect ignitor cable

 

 

tor cable

 

 

 

3.

Broken ignitor cable

3.

Replace ignitor cable

 

4.

Bad piezo ignitor

4.

Replace piezo ignitor

 

5.

Ignitor electrode broken

5.

Replace pilot assembly

 

6.

Ignitor electrode positioned wrong

6.

Replace pilot assembly

 

 

 

 

 

When ignitor button is pressed, there is

1.

Gas supply turned off or equipment

1.

Turn on gas supply or open equipment

spark at ODS/pilot but no ignition

 

shutoff valve closed

 

shutoff valve

 

2.

Control knob not in PILOT position

2.

Turn control knob to PILOT position

 

3.

Control knob not pressed in while in

3.

Press in control knob while in PILOT

 

 

PILOT position

 

position

 

4.

Air in gas lines when installed

4.

Continue holding down control knob.

 

 

 

 

Repeat igniting operation until air is

 

 

 

 

removed

 

5.

Depleted gas supply

5.

Contact local propane/LP gas company

 

6.

ODS/pilot is clogged

6.

Clean ODS/pilot (see Cleaning and

 

 

 

 

Maintenance, page 22) or replace ODS/

 

 

 

 

pilot assembly

 

7.

Gas regulator setting is not correct

7.

Replace gas regulator

 

 

 

 

 

ODS/pilot lights but flame goes out when

1.

Control knob not fully pressed in

1.

Press in control knob fully

control knob is released

2.

Control knob not pressed in long enough

2.

After ODS/pilot lights, keep control

 

 

 

 

knob pressed in 30 seconds

 

3.

Safety interlock system has been triggered

3.

Wait one minute for safety interlock sys-

 

 

 

 

tem to reset. Repeat ignition operation

 

4.

Equipment shutoff valve not fully open

4.

Fully open equipment shutoff valve

 

5.

Thermocouple connection loose at con-

5.

Hand tighten until snug, then tighten 1/4

 

 

trol valve

 

turn more

 

6.

Pilot flame not touching thermocouple,

6.

A) Contact local propane/LP gas company

 

 

which allows thermocouple to cool,

 

 

 

 

causing pilot flame to go out. This prob-

 

B) Clean ODS/pilot (see Cleaning and

 

 

lem could be caused by one or both of

 

maintenance, page 22) or replace ODS/

 

 

the following:

 

pilot assembly

 

 

A) Low gas pressure

 

 

 

 

B) Dirty or partially clogged ODS/pilot

 

 

 

7.

Thermocouple damaged

7.

Replace pilot assembly

 

8.

Control valve damaged

8.

Replace control valve

www.desatech.com

Continued

107036

19

Image 19
Contents What to do if YOU Smell GAS VENT-FREE PROPANE/LP GAS Compact FireplaceCgcftp VENT-FREE PROPANE/LP GAS Compact Fireplace Safety InformationProduct Identification Product FeaturesUnpacking Local CodesAssembling Hood AssemblyInstalling Log Assembling FireplaceConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating FireplaceRough Opening for Installing in Wall BUILT-IN Fireplace InstallationOptional Mantel Installation Mantel Clearances for BUILT-IN InstallationRemoving Valve Cover Shield Installing Blower Accessory GA3450TRemoving Upper Louver Assembly Installing Blower AssemblyInstall the switch plate on the valve Wiring Diagram For Blower Accessory Built-In Installation For Built-In InstallationAttaching Wood Base to Solid Floor Connecting to GAS SupplyExtension Cord Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Operating Fireplace For Your Safety Read Before LightingLighting Instructions Inspecting Burner Observed Problem Possible Cause Remedy TroubleshootingInlet gas pressure is too low Gas leak. See Warning statement at Replacement Parts Cleaning and MaintenanceService Hints Technical Service SpecificationsParts Centrals Cgcftp Illustrated Parts BreakdownKEY CGCF26TP Description QTY Parts ListAccessories 107036 Warranty Information

000 to 26, CGCFTP 14 specifications

Desa 000 to 26 and CGCFTP 14 represent advanced frameworks and protocols that are pushing the boundaries of digital communications and data transfer methodologies.

Desa 000 to 26 refers to a series of digital communication protocols designed to facilitate high-speed data transmission over diverse networks. These protocols have been tailored to accommodate a wide range of applications, from mobile communications to IoT devices. The primary characteristic of Desa 000 to 26 is its ability to support reliable and efficient data exchange, ensuring minimal latency and high bandwidth.

One of the main features of these protocols is adaptive bandwidth allocation, which allows the system to dynamically adjust the bandwidth based on real-time network conditions. This adaptability leads to optimal performance regardless of fluctuations in user demand or network congestion. Enhanced error correction techniques integrated into the Desa protocols also ensure data integrity during transmission, improving overall reliability.

On the other hand, CGCFTP 14 represents an evolution in file transfer protocols, specifically designed for secure and efficient data transfer between systems. This protocol leverages end-to-end encryption to safeguard data against unauthorized access during transfer. Key features of CGCFTP 14 include support for multi-threaded file transfers, which significantly accelerates the speed of large data transfers by concurrently sending multiple segments of a file.

CGCFTP 14 also incorporates advanced access control measures, allowing users to set permissions for file transfers. This characteristic is particularly valuable in corporate environments where data sensitivity is paramount. Furthermore, the protocol is compatible with various operating systems and platforms, providing ease of integration into existing systems, enhancing its versatility.

The combination of Desa 000 to 26 and CGCFTP 14 highlights the importance of robust, flexible, and secure communication methodologies in today’s digital landscape. These technologies cater to the ever-increasing demand for high-speed data transfer while ensuring security and reliability are not compromised. As businesses and individuals continue to rely on digital communication, the adoption of such innovations will undoubtedly shape the future of connectivity and data management.