CGCF26NR
VENT-FREE NATURAL GAS COMPACT FIREPLACE
INSTALLATION
Continued
MANTEL CLEARANCES FOR BUILT-IN INSTALLATION
If placing mantel above
If your installation does not meet the above minimum clearances, you must:
• raise the mantel to an acceptable height,
OR
• remove the mantel.
OPTIONAL MANTEL
INSTALLATION
Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installa- tion. Refer to instructions on page 4 for firebox assembly. Blower accessory should be installed if it is being used (see Accesso- ries, page 21).
1.Unscrew four brass screws that attach top louver to fireplace. Remove louvre from fireplace and set aside.
2.Place fireplace on wood base.
3.Place mantel around fireplace/base as- sembly.
4.Assemble brass trim kit. See Assem- bling Brass Trim.
5.Firmly snap brass trim kit on shoulder screws. Shoulder screws are located on fireplace cabinet (see Figure 12).
6.Align brass trim kit for flush fit around opening.
7.Use two 3" wood screws provided and attach fireplace base to wooden base (see Figure 12).
8.Remove brass trim kit and mantel. Be careful not to damage wall or mantel.
9.Place wood base next to wall at instal- lation location.
10.Attach wood base to floor with two
1 3/4" black screws provided (see Fig- ure 13). If the floor is concrete use an- chor method (see Attaching Wood Base to Solid Floor, page 11).
11.Install gas line. See Connecting To Gas Supply, page 11.
12.Check for leaks. See Checking Gas Connections, page 13.
13.Place mantel around fireplace. Be care- ful not to damage wall or mantel.
14.Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 12).
15.Adjust assembly to remove any gaps. At- tach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The open- ings are located at top behind the area for the brass louvers (see Figure 13).
16.Reinstall top brass louvers.
Note: All vertical | Mantel Shelf | |||
10" |
|
|
| |
measurements |
|
|
| |
are from top of | 8" |
|
|
|
|
|
| ||
fireplace | 6" |
|
|
|
|
|
| ||
opening to |
|
|
| |
2 1/2" |
|
|
| |
bottom of |
|
|
| |
|
|
|
| |
mantel shelf. |
|
|
|
|
Minimum Non- |
|
|
|
|
Combustible |
|
|
|
|
Material | 13" | 16" | 19" | 21" |
| ||||
|
|
|
|
|
Figure 11 - Minimum Mantel Clearances for Built-In Installation
Hole for 3" wood
Shoulder Screws screw for attaching fireplace to wooden base
Hole for 3" wood |
|
screw for attaching | Assembled |
fireplace to mantel | Brass Trim |
Figure 12 - Attaching Brass Trim to Fireplace
1 3/4" Screw
Wood Base
Figure 13 - Attaching Wood Base to Floor
Assembling Brass Trim (Brass trim shipped with mantel)
1.Remove packaging from three remain- ing pieces of brass trim.
2.Locate two adjusting plates with set screws, and two shims in the hardware packet.
3.Align shim under adjusting plate as shown in Figure 14.
4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 14).
5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 14).
6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.
7.Repeat steps 1 through 6 for other corner.
8.Set Brass Assembly aside for later in-
stallation.
Slot | Top | |
Set Screws | Brass | |
| Trim | |
Shim | Mitered | |
Edge | ||
| ||
Adjusting | Side | |
Plate | Brass | |
Slot | Trim | |
|
Figure 14 - Assembling Brass Trim
10 | 104326 |