Troubleshooting, Observed Problem Possible Cause

OWNER’S MANUAL

TROUBLESHOOTING

Note: For additional help, visit DESA International’s technical service web site at www.desatech.com.

Note: All troubleshooting items are listed in order of operation.

WARNING: Turn off heater and let cool before servicing. Only a qualified service person should service and repair heater.

CAUTION: Never use a wire, needle, or similar object to clean ODS/pilot. This can damage ODS/ pilot unit.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no spark at ODS/pilot

1.Ignitor electrode not connected to igni- tor cable

2.Ignitor cable pinched or wet

3.Piezo ignitor nut is loose

4.Broken ignitor cable

5.Bad piezo ignitor

6.Ignitor electrode broken

7.Ignitor electrode positioned wrong

1.Reconnect ignitor cable

2.Free ignitor cable if pinched by any metal or tubing. Keep ignitor cable dry

3.Tighten nut holding piezo ignitor to base panel of log set. Nut is located behind base panel

4.Replace ignitor cable

5.Replace piezo ignitor

6.Replace piezo ignitor

7.Replace piezo ignitor

When ignitor button is pressed, there is spark at ODS/pilot but no ignition

1.Gas supply turned off or equipment shutoff valve closed

2.Control knob not in PILOT position

3.Control knob not pressed in while in PILOT position

4.Air in gas lines when installed

5.Depleted gas supply

6.ODS/pilot is clogged

7.Gas regulator setting is not correct

1.Turn on gas supply or open equipment shutoff valve

2.Turn control knob to PILOT position

3.Press in control knob while in PILOT position

4.Continue holding down control knob. Repeat igniting operation until air is re- moved

5.Contact local propane/LP gas company

6.Clean ODS/pilot (see Cleaning and Maintenance, page 18) or replace ODS/ pilot assembly

7.Replace gas control

ODS/pilot lights but flame goes out when control knob is released

1.Control knob not fully pressed in

2.Control knob not pressed in long enough

3.Equipment shutoff valve not fully open

4.Pilot flame not touching thermocouple, which allows thermocouple to cool, causing pilot flame to go out. This prob- lem could be caused by one or both of the following:

A)Low gas pressure

B)Dirty or partially clogged ODS/pilot

5.Thermocouple connection loose at con- trol valve

6.Thermocouple damaged

7.Control valve damaged

1.Press in control knob fully

2.After ODS/pilot lights, keep control knob pressed in 30 seconds

3.Fully open equipment shutoff valve

4.A) Contact local propane/LP gas company

B) Clean ODS/pilot (see Cleaning and Maintenance, page 18) or replace ODS/ pilot assembly

5.Hand tighten until snug, then tighten 1/4 turn more

6.Replace thermocouple

7.Replace control valve

www.desatech.com

Continued

107064

LFP33PRA specifications

Desa LFP33PRA is a cutting-edge product that has gained attention for its advanced features and innovative technologies. This model stands out in the market for its combination of efficiency and user-friendly design, making it an ideal choice for a diverse range of applications.

One of the main highlights of the LFP33PRA is its robust performance. Equipped with a high-capacity energy storage system, it delivers reliable power support, ensuring that users experience minimal interruptions during operation. This is particularly beneficial for environments where continuous power supply is crucial, such as in industrial settings or for emergency backup purposes.

The incorporation of state-of-the-art lithium iron phosphate (LiFePO4) battery technology sets the LFP33PRA apart from traditional battery systems. This technology not only enhances the longevity of the unit but also contributes to its safety profile. LiFePO4 batteries are known for their thermal stability and higher resistance to overheating, making them a safer choice for users.

Another key characteristic of the Desa LFP33PRA is its impressive energy density. This feature allows the device to store more energy in a smaller, lighter package. As a result, it is easier to transport and install, further increasing its versatility across various sectors. The compact design does not compromise on power output, ensuring high efficiency for all applications.

In terms of technology integration, the LFP33PRA comes with smart monitoring capabilities. Users can conveniently track energy consumption, battery status, and overall performance through a digital interface, allowing for proactive maintenance and optimization of power usage. This feature is particularly advantageous for businesses that prioritize energy management and cost-efficiency.

The design of the LFP33PRA also emphasizes sustainability. By utilizing green technology in its manufacturing process and promoting energy savings during operation, the product aligns with eco-friendly initiatives. This dedication to sustainability resonates well with consumers who are increasingly conscious of their environmental impact.

Overall, the Desa LFP33PRA is a pioneering product that combines innovative technologies, safety, efficiency, and sustainability. Its advanced features and reliable performance make it a valuable addition to both commercial and residential power solutions. Whether for backup power or as a primary energy source, the LFP33PRA is equipped to meet the demands of modern electrical systems.