Operating Fireplace, For Your Safety Read Before Lighting

OPERATING FIREPLACE

For Your Safety Read Before Lighting

Lighting Instructions

To Turn Off Gas To Appliance

Optional Remote Operation

OPERATING FIREPLACE

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

A.This appliance is equipped with an ignition device which automatically lights the pilot. Do not try to light the pilot by hand.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch.

•Do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•If you cannot reach your gas supplier, call the fire de- partment.

C.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

NOTICE: During initial operation of new heater, burn- ing logs will give off a paper-burning smell. Orange flame will also be present. Open damper or window to vent smell. This will only last a few hours.

1.STOP! Read the safety information, above.

2.Turn off all electric power to the appliance.

3.Turn wall switch to the OFF position.

4.Open lower louver panel.

5. Turn equipment shutoff valve clockwise Clockwise to the OFF position (see Figure 49). Do not force.

6.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information above. If you don’t smell gas, go to the next step.

7.Turn equipment shutoff valve counterclockwise C-clockwiseto the ON position. Do not force.

8.Close lower louver panel.

9.Turn on all electric power to the appliance.

10.Turn the wall switch to the ON position.

11.Visually locate the pilot. The ignitor should begin to spark and the main burner should ignite once flame appears at pilot.

•If lighting the appliance for the first time each season, it may take several attempts before the supply gas can reach the pilot and main burners.

•If the appliance will not stay lit after several attempts, follow the instructions To Turn Off Gas To Appliance, be- low, and call your service technician or gas supplier.

Equipment Shutoff Valve	Adjustment
	Screw

Figure 49 - Turning Equipment Shutoff Valve to the OFF Position

TO TURN OFF GAS

TO APPLIANCE

1. Turn off the wall switch.

2.Turn off all electric power to the appliance if service is to be performed.

3.Open lower louver panel.

4.Remove front hearth brick and control access panel.

5. Turn equipment shutoff valve clockwise Clockwise to OFF.

Do not force.

6.Close lower louver panel.

Sensing Rod

Pilot Burner

Ignitor

Figure 50 - Pilot

OPTIONAL REMOTE

OPERATION

Note: The WRC receiver and hand-held remote control kit must be purchased separately (see Accessories, page 37). Follow installation instructions on page 24.

1.Turn equipment shutoff valve to ON position.You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Be sure to press the ON/OFF buttons on the hand-held remote control unit for up to 3 seconds to assure proper operation.

2.Press the ON/OFF button to turn the burner on and off.

For morevisit www..com

111253-01C

V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, VV36ENB(1) SERIES specifications

The Desa V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, and VV36ENB(1) SERIES represent an innovative lineup of gas vent-free fireplaces designed to enhance the ambiance of any living space while providing efficient heating. These models are particularly noted for their cutting-edge technology and elegant designs, ensuring they blend seamlessly with various interior styles.

The V36EP-A and V36EN-A SERIES are equipped with a highly efficient burner system that provides an impressive heat output without the need for a chimney or venting, making them highly suitable for both new constructions and renovations. These models utilize advanced control systems that allow for easy adjustment of flame height and heat levels, thereby providing users with precise control over their environment.

The VV36EPB(1) SERIES and VV36ENB(1) SERIES take these features a step further with their improved efficiency ratings and attractive detailing. These models feature realistic flame patterns and log sets that mimic the look of traditional wood-burning fireplaces, creating a warm and inviting atmosphere. The ceramic fiber logs not only enhance visual appeal but also contribute to better heat distribution and retention.

One of the standout characteristics of these fireplace series is their incorporation of advanced safety features. Equipped with oxygen depletion sensors and a durable tempered glass front, they ensure safe operation without compromising on performance. The low emissions and reduced environmental impact align with modern energy efficiency standards.

Additionally, the Desa fireplaces come with options for remote controls and programmable thermostats, allowing for hassle-free operation and energy management. Customization options are also abundant, with various finishes and styles available to fit individual preferences and home decor.

In summary, the Desa V36EP-A SERIES, V36EN-A SERIES, VV36EPB(1) SERIES, and VV36ENB(1) SERIES deliver a combination of aesthetic appeal, modern technology, and practical heating solutions. Their vent-free designs make them versatile options for homeowners seeking efficient and stylish heating methods without the need for extensive installation. With their blend of safety, efficiency, and elegance, these fireplace series are poised to redefine comfort and style in home heating.