Desa H) AND VM42E(B, M36E, M42E, VM36E, VM42E Ember and PAN Material Placement, Overtighten

Page 12

12

INSTALLATION

Gas Line Hook-Up (Cont.)

Ember and Pan Material Placement

INSTALLATION

Continued

DESA recommends that a black iron gas line be routed from the gas source, through a sediment trap (shown in Figure 18), and into the appliance, Once connected through the appliance, a flexible gas line may be used for ease of installation to gas control valve (see Figure19).

Before connecting the black iron gas line to the inside of the appliance a sediment trap must be included outside the appliance between the gas line and the gas shutoff valve. It must extend down three (3) inches beyond the center of the pipe. Prepare incoming black iron gas line with teflon tape or pipe joint compound (Check with local building codes).

CAUTION: Compounds used on threaded joints of gas piping shall be resistant to the action of Liquefied Petroleum (LP or propane), and should be applied lightly to ensure excess sealant does not enter the gas line.

WARNING: All gas piping and connections must be tested for leaks after the installation is completed.

After ensuring that the gas valve is on, apply a commer- cial leak detection solution to all connections and joints. If bubbles appear, leaks can be detected and corrected.

Do not use an open flame for leak testing and do not operate any appliance if a leak is detected.

Complete your gas installation by connecting incoming gas line with flexible gas line. Secure tightly with wrench but DO NOT

OVERTIGHTEN.

Incoming 1/2" Gas Line

Permitted by Local Codes

Sediment Trap

(Not Supplied)

 

Wall

Side

3" Min.

 

Appliance

(76mm)

Of

 

EMBER AND PAN MATERIAL PLACEMENT

1.Open the bag(s) of vermiculite and fill the entire burner pan until the burner tube is completely covered (see Figure 20).

2.Smooth the pan material just even with edges of the burner pan.

3.Remove the ember material from the bag and flatten small amounts into quarter size pieces and lay on top of the surface of the pan material (see Figure 21).

4.Place just enough to cover the entire surface and leave about a 1/2 inch gap under the lower grate members to allow air to flow (see Figure 22).

Grate

Vermiculite

Burner Pan

(Pan Material)

 

 

 

Figure 20 - Fill Entire Burner Pan with Vermiculite

 

Ember

Vermiculite

 

Grate

Material

Burner Pan

(Pan Material)

 

 

 

Figure 18 - Sediment Trap

Figure 21 - Ember Material on Surface of Pan Material

(Vermiculite)

 

Pan and Ember

 

 

 

Grate

 

 

 

 

 

Material

 

Red Surface Indicates

 

 

 

 

 

 

 

 

 

 

0.5"

 

Equipment

For Propane/LP Use Only

 

 

 

 

 

 

 

 

 

Flexible Gas Line

 

 

 

 

 

 

 

Shutoff Valve

Do NOT Kink

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1/2" NPT Incoming

 

 

0.5"

 

 

 

Gas Line

Inlet Pressure Tap

Outlet Pressure Tap

Burner Pan

 

 

Note:

 

 

 

 

 

1)

Wire Connections Not Shown for Clarity

 

 

2)

* 1/8" NPT Plugged Tapping

 

Figure 22 - Pan and Ember Material Clearances

Figure 19 - Connecting Flexible Gas Line to Electronic Valve

For morevisit www..com

108796-01D

Page 11 Page 13
Image 12
Page 11 Page 13
Contents For Your Safety Vent Decorative GAS FireplaceElectronic Ignition Natural GAS What to do if YOU Smell GASTable of Contents Safety InformationUnpacking Introduction Before YOU BeginM36EB,H/VM36EB,H M42EB,H/VM42EB,H Product Specifications ModelPRE-INSTALLATION Preparation Selecting LocationClearances Mantel Clearances and Wall Details M36EB,H M42EB,HVM36EB,H VM42EB,H M36EB,H M42EB,H VM36EB,H VM42EB,HInstalling Transition Pipe and Starter Collar FramingVenting Installation Typical B-Vent ConfigurationChecking for Proper Venting Min Roof PitchInstallation Wall Switch InstallationOptional Remote Control GAS Line HOOK-UPEmber and PAN Material Placement OvertightenLOG Placement for M36E/VM36E Models Installing Logs 1LOG Placement for M42E/VM42E Models Installing Logs 1A, 1BInstalling Optional Glass Door Accessory Combustion AIR KIT Model AK4 OptionalAppliance Enclosure Opening Vent Damper DoorFor Your Safety Read Before Lighting Operating FireplaceLighting Instructions To Turn OFF GAS To ApplianceCleaning Maintenance Inspecting BurnersService Hints Technical ServiceWiring Diagram Replacement PartsTroubleshooting Observed Problem Possible Cause RemedyTop Gas leak. See Warning statement atIllustrated Parts Breakdown VM42EB,H ModelsParts List VM36EB/VM42EBLogs for M36EB,H,M42EB,H, VM36EB,H and VM42EB,H Models Logset for M36EB,H and VM36EB,H ModelsAccessories Warranty Information

M36E, M42E, VM36E, VM42E, H) AND VM42E(B specifications

Desa M36E, M42E, VM36E, VM42E(H), and VM42E(B) are advanced heating solutions engineered for enhanced performance and versatility in both residential and commercial settings. These models stand out for their efficient heating capabilities and innovative designs, which cater to a variety of heating needs.

The Desa M36E and M42E models offer a robust heating output, making them ideal for larger spaces. The M36E boasts a compact structure that accommodates small to medium areas, while the M42E provides greater output suitable for bigger rooms. Both units are equipped with high-efficiency burners that ensure optimal fuel utilization, leading to significant cost savings over time.

The VM36E and VM42E(H) models take efficiency to the next level. Their advanced combustion technology maximizes heat production while minimizing emissions, aligning with modern environmental standards. The VM36E features a versatile design, allowing it to seamlessly integrate into various décor styles, while providing a steady flow of warm air. Meanwhile, the VM42E(H) is enhanced with a hybrid heating system, enabling users to switch between energy sources, which adds to its adaptability in differing climates or situations.

The VM42E(B) model introduces an innovative breakthrough in heating technology by incorporating smart control features. Users can effortlessly regulate their heating preferences through a smartphone application, allowing for remote management and programming based on individual schedules. This smart technology not only enhances user convenience but also supports energy conservation by promoting efficient usage patterns.

All models come equipped with safety features such as automatic shut-off mechanisms, ensuring peace of mind during operation. The units are designed with durable materials, capable of withstanding prolonged use while maintaining aesthetic appeal.

In summary, Desa's M36E, M42E, VM36E, VM42E(H), and VM42E(B) represent the forefront of modern heating solutions, combining high efficiency, innovative technologies, and user-friendly features. Their diverse applications, coupled with intelligent design, ensure they meet the evolving demands of today's consumers while providing warmth and comfort in any setting.
Top Page Image Contents