Desa T32N-A, CGDV32NR, T32P-A, CGDV32PR installation manual ON/OFF Series, Thermostat Series

Page 26

26

OPERATING FIREPLACE

Optional Hand-Held Remote Operation (Cont.) Operating Optional GWMT1 Wall Mounted Thermostat

OPERATING FIREPLACE

Continued

ON/OFF SERIES

(Model HRC200 and HRC201)

Hold the control button on the hand-held remote until burner turns on. Hold the control button again until burner turns off (see Figure 52).

TO LOCK press both buttons on hand-held remote control until light stops flashing. Hand-held remote control is now locked. If the fire is on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed.

TO UNLOCK press both buttons together on hand-held remote control until the light stops flashing. The hand-held remote is now unlocked.

Indicator

 

Light

Control

 

 

Button

Note: Do not hold the hand-held remote for a long time. Body temperature will affect its operation in the AUTO mode.

Safety Features

When away from home for an extended period of time or as a child safety feature to prevent accidental ignition of the fireplace, the re- ceiver ON/OFF/REMOTE switch should be in the OFF position.

Auto Shutoff Feature

1.If the average room temperature exceeds 82 degrees Fahrenheit (28 degrees Centigrade), the hand-held remote control will perform a safety override and shut the fireplace off. This feature is not available in the MANU mode.

2.The receiver continuously receives signals from the hand- held remote to control the room temperature. If the hand- held remote is misplaced, obstructed or for any reason cannot transmit to the receiver, the receiver will shut off the fireplace after 8 minutes.

Key Pad Lock Feature

This feature allows the user to lock/unlock the keypad on the hand- held remote in the MANU or AUTO mode to prevent inadvertent operation (i.e. children operating the hand-held remote control, etc.). The keypad is locked in either on or off. Press the POWER and LOCK buttons together to turn the unit on or off.

Figure 52 - On/Off Hand-Held Remote Control Unit (HRC100/HRC101)

THERMOSTAT SERIES

(Model GHRCTB and CGHRCTB)

The hand-held remote can be operated using either the manual mode (MANU) or thermostatic mode (AUTO) (see Figure 53). To selectFahrenheit/Centigrademodedisplay,carefullypressthe˚C/˚F mode button with the end of a paper clip or similar blunt object.

Indicator Light

Locks System to Prevent Accidental Ignition

 

AUTO

ROOM

SET

TEMP

TEMP

LOCK

TEMP

POWER

 

Digital Display

Shows Temperature

and Settings

Turns Hand-Held Remote On or Off and Allows You to Choose the Manual Setting

Manual Mode

1.Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2.Press the MANU button to turn on the fireplace.

3.Press the POWER and LOCK buttons together to turn off the fireplace.

Auto (Thermostatic) Mode

1.Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2.Press AUTO button to select this mode.

3.Set the desired room temperature by pressing the TEMP + or - buttons.

4.Press the POWER and LOCK buttons together to turn off the fireplace.

Note: Do not leave the hand-held remote in the AUTO mode close to the fireplace. The radiant heat from the fireplace will turn off the fireplace. Ideally, place the hand-held remote in the center of the room facing towards the fireplace.

Turns

MANU

ºC/ºF

AUTO

Burners

 

Selects

 

 

On or Off

 

 

 

 

AUTO Mode

 

 

 

Increases or

 

 

°C/°F Mode

 

 

Button

Decreases Room

 

 

 

 

 

Temperature in

 

 

 

AUTO Mode

 

 

 

Figure 53 - Thermostat Hand-Held Remote Control Unit (HRC200/HRC201)

www.desatech.com

116646-01B

Page 25 Page 27
Image 26
Page 25 Page 27
Contents For Your Safety What to do if YOU Smell GAS OWNER’S Operation Installation ManualFor Your Safety Save this manual for future referenceTable of Contents Safety InformationSafety Information Product Identification Local CodesLocation and Space Requirements Product FeaturesPRE-INSTALLATION Preparation Clearances Framing and FinishingLocation of Termination CAP Termination CAP AIR Supply Inlet GAS MeterVenting Installation Instructions Installation PrecautionsInstallation Planning Horizontal Termination InstallationInstalling Siding Standoff Combustible Cap must be removable for vent inspection MaintenanceHorizontal Termination Configurations VerticalCorner Installation Horizontal System Installation Using TWO Elbows Venting with Two 90 ElbowsInstallation for Vertical Termination Flat Ceiling InstallationVertical Termination Configurations Venting with One 90 ElbowHigh Altitude Installation Vertical VentingInstalling Optional Blower Accessories Venting InstallationFireplace Installation Check GAS TypeModel BKT Installation Blower see FigureInstallation Items Needed Installing GAS Piping to Fireplace LocationBlower Wiring Diagram Or servicing. Correct all leaks at once Connecting Fireplace to GAS SupplyChecking GAS Connections Installing Optional Wall Mount Switch GWMS2 Pressure Testing Fireplace Gas ConnectionsRemote Control Unit Installing Remote ReceiverInstalling 9-Volt Alkaline Battery in Hand-Held Removing Louver PanelsRemoving Glass Door Installing Optional Brick Liner Model BL32DCleaning Glass Door Installing LOGS, Lava Rock and Glowing Embers Installing Side Brick PanelsLighting Instructions For Your Safety Read Before LightingOperating Fireplace Optional HAND-HELD Remote Operation Manual Lighting ProcedureTo Turn OFF GAS To Appliance Shutting Off Burners Only pilot stays litON/OFF Series Thermostat SeriesInspecting Burners Operating Optional Blower AccessoryPilot Assembly Operating Optional GWMT1 Wall Mounted ThermostatPilot and Burners Cleaning and MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible Cause RemedyInlet gas pressure is too low Gas leak. See Warning statement AboveIllustrated Parts Breakdown CGDV32NR CGDV32PRParts List Parts ListTechnical Service Replacement PartsService Hints SpecificationsOwners Registration Form Postage Required Accessories Warranty Information Keep this Warranty

(V)T32P-A SERIES, (V)T32N-A SERIES, T32N-A, CGDV32NR, T32P-A, CGDV32PR specifications

The T32N-A, CGDV32NR, T32P-A, CGDV32PR, (V)T32P-A SERIES, and (V)T32N-A SERIES are distinguished series of innovative technologies designed to meet diverse industrial demands. These models exemplify cutting-edge engineering, tailored for performance, efficiency, and adaptability.

One of the primary features of these series is their robust construction. The T32N-A and its counterparts are built with high-quality materials, ensuring durability and longevity even in harsh operating conditions. This reliability makes them ideal for applications that require consistent performance under stress. The engineering design incorporates advanced computational techniques, resulting in streamlined shapes that enhance aerodynamic efficiency.

The CGDV32NR and CGDV32PR series are particularly notable for their fluid management capabilities. These models are equipped with sophisticated flow control technologies that optimize the movement of fluids, minimizing waste and energy consumption. This efficiency is crucial for industries such as water treatment, chemical processing, and food production, where resource conservation is paramount.

Additionally, the (V)T32P-A and (V)T32N-A SERIES introduce variable technology options, allowing for enhanced versatility in operation. These models feature adjustable parameters that can be fine-tuned to suit specific processes, making them adaptable for various industrial applications. This flexibility minimizes downtime and maximizes productivity, providing a significant competitive edge.

In terms of user interface, these series emphasize user-friendly controls and robust monitoring systems. Operators can easily track performance metrics and make real-time adjustments, ensuring optimal functionality. Advanced sensors integrated into the systems enhance safety by providing alerts and diagnostics that preempt potential issues.

Environmental considerations are also a critical focus of these series. The T32N-A and associated models are designed with energy efficiency in mind, aligning with contemporary sustainability goals across industries. Reduced energy consumption and lower emissions are significant advantages, contributing to a smaller ecological footprint.

Overall, the T32N-A, CGDV32NR, T32P-A, CGDV32PR, (V)T32P-A SERIES, and (V)T32N-A SERIES stand out for their exceptional features, intuitive technology, and adaptability. Suitable for various industrial applications, they represent the forefront of innovation, combining performance and efficiency to meet the evolving demands of modern industry. As businesses continue to prioritize reliability and sustainability, these series are poised to play a critical role in driving progress across sectors.
Top Page Image Contents