Continental BCDV48N, BCDV48P manual Optional Blower Installation, Optional FAN Installation

21

OPTIONAL BLOWER INSTALLATION

		INSTALLATION TO BE	threaded stud using the lock washer and wing nut provided. Ensure
		DONE BY A QUALIFIED that the blower does not touch the fi replace base or the fi rebox.
		INSTALLER and must
		be electrically connected Attach the connectors from the black
		and grounded in accord- and white wires to the thermodisc and
	FIGURE 44	ance with local codes.	secure the thermodisc bracket to the
		In the absence of local	securing stud at the bottom left of the
		codes, use the current	unit using a lock washer and wing nut.
		CSA C22.1 CANADIAN ELEC- Ensure that the thermodisc touches
		TRICAL CODE in Canada the fi rebox wall.
		or the ANSI/NFPA 70 Attach the connectors from the black
		NATIONAL ELECTRICAL CODE	and red wires to the blower.
		in the United States	Attach and secure the varia-	FIGURE 50
If the fireplace was not previously equipped
			ble speed switch using the nut
with a blower: route a grounded 2-wire,			provided. Plug the harness
60hz power cable to the receptacle / junc-			cord into the receptacle.
tion box. At this point, it must be strain			FIGURE 51
relieved and insulated.			The wire harness provided in this
The three slots on the blower mount-			kit is a universal harness. When
ing bracket allow ease of adjustment			installed, ensure that any excess
when attaching the blower. For a quiet		FIGURE 45	wire is contained, preventing it from mak-
running blower, do not allow the as-			ing contact with moving or hot objects.
sembly to sit on the fi rebox base.			Because the blower is thermally activated,
Slide the vibration reducing pad (A) into the clip (C) and up against
			when turned on, it will automatically start
the threaded stud (B) at the other end. The blower must be able to
			approximately 10 minutes after lighting
be positioned	FIGURE 46	FIGURE 47
			the fireplace and will run for approximately
entirely onto
			30-45 minutes after the fireplace has been
the pad.	B
			turned off. Use of the fan increases the output of heat.
Tilt the blower
			Drywall dust will penetrate into the blower bearings, causing irrepara-
onto its side.
		C	ble damage. Care must be taken to prevent drywall dust from coming
Slide it past	A
			into contact with the blower or its compartment. Any damage resulting
the controls
and into the			from this condition is not covered by the warranty policy.
clip (C). Se-
cure to the
	OPTIONAL FAN INSTALLATION
ELECTRICAL INSTALLATION			route a grounded 2-wire, 60hz power cable to the junction box. At
TO BE DONE BY A QUALI-			this point, it must be strain relieved and insulated.
FIED INSTALLER and must			The wire harness provided in this kit is a universal harness. When
be connected and grounded in			installed, ensure that any excess wire is contained, preventing it from
accordance with local codes. In			making contact with moving or hot objects.
the absence of local codes, use			To ease installation of the fan, remove the hinge screen and valve
the current CSA C22.1 CANADIAN
			control door (lower louvres) from the base of the fi replace.
ELECTRICAL CODE in Canada or the
			Position the vibration reducing pad into the clip and onto the threaded
ANSI/NFPA 70 NATIONAL ELECTRI-
			stud at the other end, piercing a hole into the pad. The fan assembly
CAL CODE in the United States.
			must be able to be positioned entirely onto the pad.
To safely install the fan, turn off
			Slide the fan assembly past the controls and into the clip. Secure
the electricity fi rst.
		FIGURE 48	using the lock washer and nut provided.
If the fireplace was not previ-

ously equipped with a fan: Plug the harness cord into the receptacle.

GD36 THERMOSTATIC SENSOR CONTROL

This optional kit is meant to be used only in conjunction with the GD65 Fan Kit, shown above, which may

be ordered from your Wolf Steel / Continental® dealer.

With the thermostatic sensor op- tion, the fan, when turned on, be- comes thermally activated, and will automatically run approximately 15-30 minutes after the fi replace

has been lit and for approximately

30-45 minutes after the fi replaceFIGURE 49 has been turned off.

Use of the fan increases the output of heat.

Unplug the power cord from the receptacle. Connect all wires as shown.

Attach and secure the sensor assembly bracket to the securing stud located next to the

receptacle/junction box at the bottom left of the unit using the lock washer and wing nut. Ensure that the thermodisc touches

the fi rebox wall.

FIGURE 52

Plug the power cord back into the receptacle.

When installed, ensure that any excess wire is contained, preventing it from making contact with moving or hot objects.

W415-0327 / B / 12.07.07