GAS Installation, Framing, Conversion Kits

GAS INSTALLATION

Proceed once the vent installation is complete.

NOTE: All gas connections must be contained within the ﬁreplace when complete.

1.Move the ﬁreplace into position and secure to the ﬂoor through the 1/4" holes located at either side of the base.

2.The ﬁreplace is designed to accept 3/8" gas supply line. The

ﬁreplace is equipped with a 3/8" manual shut-off valve.

3.Connect the gas supply in accordance to local codes. In the absence thereof, install according to the National Installation Code.

4.When ﬂ exing any gas line, support the gas valve so that the lines are not bent or kinked.

5.Check for gas leaks by brushing on a soap and water solution.

DO NOT USE OPEN FLAME.

Purge all gas lines with the glass door of the stove removed. Assure that a continuous gas ﬂow is at the burner before re-in- stalling the door.

OPTIONAL WALL SWITCH

INSTALLATION

For ease of accessibility, an optional remote wall switch may be installed in a convenient location. A 20’ length of millivolt wire is connected to the gas valve for the wall switch. However if a greater length is required route 2-strand (solid core) millivolt wire through the electrical hole lo- cated at the bottom left side of the unit. The recommended maximum

lead length depends on wire size:
	WIRE SIZE	MAX. LENGTH
	14 gauge	100 feet
	16 gauge	60 feet
	18 gauge	40 feet

Attach the two leads to terminals 1 and 3 located on the gas valve.

FIGURE 33

Conversion Kits

The mobile home appliance is ﬁ eld convertible between Natural Gas (NG) and Propane (LP).

To convert from one gas to another consult your Continental dealer/ distributor.

FRAMING

Minimum clearance to combustible construction from ﬁreplace and vent surfaces:

Framing	0" to stand-offs
Finishing	0" to rear, sides and bottom
Non-combustible ﬁ nishing	8" to top
All around the vent pipe	2"
Recessed depth	23"
Enclosure top	55" from bottom of unit
Clearance to ceiling	84" from bottom of unit

Note: In order to avoid the possibility of exposed insulation or vapour barrier coming in contact with the ﬁreplace body, it is recommended that the walls of the ﬁreplace enclosure be “ﬁnished” (ie: drywall/sheetrock), as you would ﬁ nish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the cavity.

It is best to frame your ﬁreplace after it is positioned and the vent system is installed. Use 2x4's and frame to local building codes.

It is not necessary to install a hearth extension with this ﬁ replace system.

When roughing in the ﬁ replace, raise the ﬁreplace to accommodate for the thickness of the ﬁ nished ﬂ oor materials, i.e. tile, carpeting, hard wood, which if not planned for will interfere with the opening of the lower access door and the installation of many decorative ﬂashing accessories.

Objects placed in front of the ﬁreplace should be kept a minimum of 48" away from the front face.

Combustible materials may be installed ﬂ ush with the front of the ﬁre- place but must not cover any of the black face areas of the ﬁreplace. Non-combustible material (brick, stone or ceramic tile) may protrude in these areas.

FIGURE 34

MOBILE HOME INSTALLATION

This appliance is certiﬁed to be installed as an OEM (Original Equip- ment Manufacturer) installation in a manufactured home or mobile home and must be installed in accordance with the manufacturer’s instructions and the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States or the Mobile Home Standard, CAN/CSA Z240 MH Series, in Canada. This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is supplied with the mobile home appliance.

This Mobile/Manufactured Home Listed appliance comes factory equipped with a means to secure the unit. The ﬁreplace is equipped with two 1/4” diameter holes located in the front left and right corners of the base. For mobile home installations, the ﬁreplace must be fas- tened in place. Use #10 hex head screws, inserted through the holes in the base to secure. Always turn off the pilot and the fuel supply at the source, prior to moving the mobile home.

After moving the mobile home and prior to lighting the ﬁreplace, ensure that the logs are positioned correctly.

This appliance is certiﬁ ed to be installed in an aftermarket perma- nently located, manufactured (mobile) home, where not prohibited by local codes.

This ﬁreplace is only for use with the type of gas indicated on the rating plate. This ﬁreplace is not convertible for use with other gases, unless a certiﬁ ed kit is used.

51 1/2"

FIGURES 35a-b

	"
1/2		"
		16
48	11/
48	72
	72

W415-0327 / B / 12.07.07

BCDV48N, BCDV48P specifications

The Continental BCDV48P and BCDV48N are cutting-edge commercial vehicles designed to meet the needs of modern logistics and transportation. Both models showcase Continental's commitment to engineering excellence, offering a blend of advanced technologies, safety features, and performance characteristics.

The BCDV48P primarily focuses on urban delivery scenarios, making it ideal for navigating congested city streets. Its compact design enables agile maneuverability, while the spacious cargo area ensures it can accommodate a variety of freight types. The BCDV48N, on the other hand, is designed for slightly heavier loads, featuring enhanced payload capacity while retaining a similar compact footprint.

One of the standout features of both models is the innovative electric drive system. This powertrain technology not only reduces emissions but also enhances energy efficiency, making them environmentally friendly options for businesses looking to lower their carbon footprint. The low noise operation of the electric drive offers a distinct advantage in urban environments, allowing for quiet deliveries even in residential areas.

Safety is paramount in the BCDV48P and BCDV48N. Both vehicles come equipped with an array of advanced safety systems, including electronic stability control and anti-lock braking systems. Additionally, features such as rearview cameras and parking sensors facilitate easy navigation and parking, contributing to overall operational safety.

Technologically, the BCDV models are equipped with a state-of-the-art infotainment system that provides real-time navigation and connectivity features. Fleet managers can track vehicle performance, monitor energy consumption, and optimize routes through integrated telematics, significantly enhancing operational efficiency.

The ergonomic design of the driver’s cabin focuses on comfort and functionality. With spacious seating, adjustable steering, and a user-friendly dashboard layout, drivers can maintain high levels of productivity throughout their shifts. Ample storage compartments ensure that essential tools and equipment are within easy reach.

In summary, the Continental BCDV48P and BCDV48N are versatile vehicles that blend advanced technologies with practical features. Their commitment to sustainability, safety, and user experience makes them ideal choices for businesses looking to optimize their logistics operations while minimizing their impact on the environment. These models stand as a testament to Continental's innovation in the commercial vehicle segment.