Continental BCDV48N, BCDV48P Adjustments, Pilot Burner Adjustment, Venturi Adjustment, Front Rear

Page 23

23

ADJUSTMENTS

PILOT BURNER ADJUSTMENT

Adjust the pilot screw to provide properly sized fl ame. Turn in a clockwise direction to reduce the gas fl ow.

FIGURE 55

FIGURE 56

VENTURI ADJUSTMENT

Air shutters have been factory set open according to the chart below:

 

FRONT

REAR

NG

1/8"

7/32"

LP

3/16"

3/8"

These settings are for the maximum horizontal vent run.- Adjust- ment may be required depending on fuel type, vent confi guration and altitude.

Closing the air shutter will cause a more yellow fl ame, but can lead to carboning. Opening the air shutter will cause a more blue fl ame, but can cause fl ame lifting from the burner ports. The fl ame may not appear yellow immediately; allow 15 to 30 minutes for the fi nal fl ame colour to be established.

FIGURE 57

Air shutter adjustment must only be done by a qualified

installer!

FIGURE 58

VENTURI COVER

To access the air shutter, remove the two screws that secure the cover to the air housing, taking care not to damage the gasket.

NOTE: Ensure burner is seated onto orifi ce

W415-0327 / B / 12.07.07

Image 23
Contents W415-0327 / B $10.00 Table of Contents Conditions and Limitations Care of GLASS, and Plated Parts General InstructionsGeneral Information Installation Overview Supplier VentingVenting Lengths Minimum AIR Terminal Location Clearances Periscope Termination Special Vent InstallationsVertical rise is less than horizontal run Venting Application Flow ChartVertical Termination Elbow Vent Length Values When HT VTHorizontal Termination DefinitionsFormula 1 HT 4.2 VT Formula 2 HT + VT 24.75 feet = 10.9 + 15 = 25.9 ft Vertical Termination= .0345+90+90+90-135=5.4 = HR + HO = 5.5 + 5.4 = 10.9 ft3V T = .0345 + 90 + 90 + 90 135 = 5.4 ft= H R + H O = 8 + 5.4 = 13.4 ft + V T = 13.4 + 2.5 = 15.9 ftVent Heat Shield Installation Installation Wall and Ceiling ProtectionHorizontal Installation Vertical InstallationFireplace Vent Connection Using Flexible Vent ComponentsRestricting Vertical Vents Using Rigid Vent ComponentsVertical Venting Installation Framing GAS InstallationOptional Wall Switch Installation Mobile Home InstallationFrom bottom of unit 84 from bottom of unit Minimum Mantel and Enclosure ClearancesFinishing Nailing TAB InstallationLOG Placement / Glowing Embers Vermiculite Logo PlacementCharcoal Embers Louvre Installation Glowing EmbersGD36 Thermostatic Sensor Control Optional Blower InstallationOptional FAN Installation Fireplace Operation / MaintenanceMaintenance Operating InstructionsFront Rear AdjustmentsPilot Burner Adjustment Venturi AdjustmentFlexible Vent Kits Roof Terminal Kits ReplacementsReplacement Parts AccessoriesW415-0327 / B Symptom Problem Test Solution Trouble Shooting GuideWise Firmly to RESEAL. do not Overtorque W415-0327 / B

BCDV48N, BCDV48P specifications

The Continental BCDV48P and BCDV48N are cutting-edge commercial vehicles designed to meet the needs of modern logistics and transportation. Both models showcase Continental's commitment to engineering excellence, offering a blend of advanced technologies, safety features, and performance characteristics.

The BCDV48P primarily focuses on urban delivery scenarios, making it ideal for navigating congested city streets. Its compact design enables agile maneuverability, while the spacious cargo area ensures it can accommodate a variety of freight types. The BCDV48N, on the other hand, is designed for slightly heavier loads, featuring enhanced payload capacity while retaining a similar compact footprint.

One of the standout features of both models is the innovative electric drive system. This powertrain technology not only reduces emissions but also enhances energy efficiency, making them environmentally friendly options for businesses looking to lower their carbon footprint. The low noise operation of the electric drive offers a distinct advantage in urban environments, allowing for quiet deliveries even in residential areas.

Safety is paramount in the BCDV48P and BCDV48N. Both vehicles come equipped with an array of advanced safety systems, including electronic stability control and anti-lock braking systems. Additionally, features such as rearview cameras and parking sensors facilitate easy navigation and parking, contributing to overall operational safety.

Technologically, the BCDV models are equipped with a state-of-the-art infotainment system that provides real-time navigation and connectivity features. Fleet managers can track vehicle performance, monitor energy consumption, and optimize routes through integrated telematics, significantly enhancing operational efficiency.

The ergonomic design of the driver’s cabin focuses on comfort and functionality. With spacious seating, adjustable steering, and a user-friendly dashboard layout, drivers can maintain high levels of productivity throughout their shifts. Ample storage compartments ensure that essential tools and equipment are within easy reach.

In summary, the Continental BCDV48P and BCDV48N are versatile vehicles that blend advanced technologies with practical features. Their commitment to sustainability, safety, and user experience makes them ideal choices for businesses looking to optimize their logistics operations while minimizing their impact on the environment. These models stand as a testament to Continental's innovation in the commercial vehicle segment.