Desa SDVBPD, SDVBND installation manual Installing Optional Wall Mounted Thermostat GWMT1

Page 23

STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION

Installing Optional Wall Mounted Thermostat - GWMT1 Installing Optional Wireless Hand-Held Remote Control Accessories - (C)GHRCB and (C)GHRCTB Series

23

STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION

Continued

INSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1

WARNING: Installation must be done by a qualified installer familiar with low voltage wiring procedures.

WARNING: Do not connect this thermostat to any electrical source! Electrical shock and/or fire hazard will occur.

1.Open lower door panel. The valve is attached to the underside of the burner system assembly.

2.Disconnect from the valve the wires running from the ON/ OFF switch.

3.Connect one terminal of the wire for the wall thermostat to the THTP terminal on the valve. Connect remaining wire terminal to the TH terminal on the valve. Make sure that the wire termi- nals are in the positions on the unit as pictured in Figure 45, page 22. If wires are not connected as shown the thermostat will not work.

4.Route the wire to a convenient location to mount your thermo- stat (no outside wall). IMPORTANT: The wire must not ex- ceed 25 feet in length. The thermostat should be mounted 54" above the floor in a location where there is good air circula- tion. Avoid heat sources such as lamps, direct sunlight, fire- place, or heat and air conditioning ducts.

5.Gently remove the cover of the thermostat from the base. Grasp the sides of the cover firmly and pull to separate from the base.

6.Feed the electrical wires through the rectangular slots (from the back) on each side of the base (see Figure 46).

WARNING: Do not connect this thermostat to a power source. Electrical shock and/or fire hazard will occur.

7.Connect one bare wire end to each terminal (“W” and “R”) of the thermostat base (see Figure 47).

8.Install the base to the wall with screws provided with thermostat.

9.Move the temperature adjustment back and forth to insure the bimetal is free from restrictions.

10.Replace the cover onto the base. (Upon installation, the ther- mostat must be allowed to stabilize at room temperature for a minimum of 30 minutes for proper operation.)

11.Set the temperature adjustment to the desired setting. This ther- mostat has been electronically calibrated at the factory. No ad- justment or leveling is necessary.

Feed wires through rectangular slots

Terminal “W”

W

 

Terminal “R”

 

R

Figure 46 - Back View of

Figure 47 - Thermostat

Thermostat Base

Base Terminal “W” and “R”

INSTALLING OPTIONAL WIRELESS HAND- HELD REMOTE CONTROL ACCESSORIES - (C)GHRCB AND (C)GHRCTB SERIES

NOTICE: Use only alkaline batteries (not included).

Installing Remote Receiver and 9-volt Alkaline Battery

1.Open bottom door on stove body.

2.Disconnect wires from THTP and TH on control valve that lead to the switch (see Figure 45, page 22). Discard switch plate, screws, and nuts.

3.Install 9-volt battery (not included) into receiver battery clip and connect to terminals (see Figure 48).

Receiver

9-Volt

BatteryTerminal Wires

Battery Clip

Figure 48 - Installing Battery in Receiver

For morevisit www..com

112126-01B

Page 22 Page 24
Image 23
Page 22 Page 24
Contents VH series Stove OWNER’S Operation and Installation ManualFor Your Safety For Your Safety What to do if YOU Smell GASSafety Information Table of ContentsWith stove Product IdentificationGlossary of Terms PRE-INSTALLATION Preparation Product FeaturesLocal Codes Stove Body Assembly PRE-INSTALLATION PreparationCast Iron Stove and DIRECT-VENT Burner System Assembly Locating Threaded Holes for Legs and Door Attachment Amity Models Installing DIRECT-VENT Burner System Into Stove BodyRemoving Front Surround Panel Removing Screen OptionalTOP View Installing Optional Blower Accessory Installing the BlowerBlower Wiring Layout Thermostat Blower Shown Installing Rear CoverLocation of Vent Termination General VentingGeneral Venting Installation Planning Venting InstallationInstallation Precautions Installing Vent System in a Chase Installation for Horizontal TerminationVent Opening Requirements Venting with Two 90 Elbows Horizontal Termination ConfigurationsHorizontal Venting Venting with Three 90 ElbowsFlat Ceiling Installation Installation for Vertical TerminationVenting with Two 90 Elbow Cathedral Ceiling InstallationVertical Termination Configurations Venting with Two Elbows Vertical Venting Configuration Using Two 90ElbowsNumber Description High Altitude InstallationParts Lists for Venting Kits and Components Vertical VentingCheck GAS Type Stove and DIRECT-VENT Burner System InstallationInstalling GAS Piping to STOVE/ Burner System Location Installation Items NeededChecking GAS Connections Connecting STOVE/BURNER System to GAS SupplyPressure Testing Gas Supply Piping System Pressure Testing Burner System Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Remote Receiver and 9-volt Alkaline Battery Installing Optional Wall Mounted Thermostat GWMT1REMOVING/REPLACING Glass Door Installing Remote ReceiverInstalling Log No Installing Log No Installing LOGS, Lava Rock and Glowing EmbersTo Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Stove with Burner System Lighting InstructionsThermostat Series Models Ghrctb and Cghrctb Manual LightingOptional HAND-HELD Remote Operation ON/OFF Series Models Ghrcb and CghrcbOperating Optional GWMT1 Wall Mounted Thermostat Operating Optional Blower AccessoryPilot Assembly Inspecting BurnersLogs Cleaning and MaintenanceGlass Door Pilot and BurnersObserved Problem Possible Cause Remedy TroubleshootingOrifice Above Gas leak. See Warning statementParts Under Warranty SpecificationsWiring Diagram Replacement PartsModels Sdvbnd Sdvbpd Illustrated Parts BreakdownModels SDVBND, Sdvbpd Parts ListVictor Hearth Stove Body Indicates Color Suffix Designation Oxford Amity Stove BodyDescription QTY Indicates Color Suffix DesignationAccessories Technical ServiceService Hints Owners Registration Form For Com 112126-01B Warranty Information
Related manuals
Manual 42 pages 850 b

SDVBPD, SDVBND specifications

Desa SDVBPD and SDVBND are pioneering advancements in the domain of digital communication, designed to optimize services, enhance user engagement, and streamline processes in various sectors, including education, healthcare, and local governance. These systems have emerged as essential tools for efficient information dissemination and resource management.

One of the main features of Desa SDVBPD is its focus on decentralized communication. By utilizing local infrastructure, this system empowers communities to share information effectively and enhance interactions among residents. It enables local authorities to communicate directly with citizens, ensuring that pertinent information reaches the intended audience promptly. This feature is especially vital in emergency situations, where timely updates can significantly impact community safety and preparedness.

Similarly, SDVBND offers a robust platform for managing digital transactions and records. Its integration of blockchain technology ensures that all data processed is secure, immutable, and transparent. This characteristic is particularly beneficial for local government operations, as it minimizes the risk of fraud and enhances accountability in public service delivery. By leveraging this technology, Desa SDVBND can facilitate smooth and fast transactions between citizens and government entities, thereby transforming the way public services are accessed.

Another remarkable aspect of both systems is their accessibility. Designed with user-friendly interfaces, these platforms cater to individuals of varying technological proficiencies. Mobile compatibility allows users to engage with the systems from smartphones and tablets, making it easier to stay informed and involved. Furthermore, the platforms are multilingual, ensuring that communication is inclusive, reaching diverse populations within communities.

Interoperability stands out as a significant characteristic of Desa SDVBPD and SDVBND. Both systems are designed to seamlessly integrate with existing infrastructure and technologies, such as cloud computing and artificial intelligence. This adaptability enhances their functionality, enabling real-time data analysis and improved decision-making.

In conclusion, Desa SDVBPD and SDVBND represent a significant leap forward in community engagement and service delivery. By leveraging decentralized communication, blockchain technology, accessibility, and interoperability, these systems not only improve operational efficiency but also foster a sense of community empowerment. As they continue to evolve, they hold great promise for enabling smarter, more connected communities that can thrive in an increasingly digital world.
Top Page Image Contents