Desa SDVBND, SDVBPD Operating Stove with Burner System, For Your Safety Read Before Lighting

Page 26

26

OPERATING STOVE AND BURNER SYSTEM

For Your Safety Read Before Opening

Lighting Instructions

To Turn Off Gas To Appliance

OPERATING STOVE WITH BURNER SYSTEM

FOR YOUR SAFETY

READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing prop- erty damage, personal injury or loss of life.

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Do not try to light any appliance.

•Do not touch any electric switch; do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don't try to repair it, call a qualified service technician. Force or attempted repair may result in a fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

LIGHTING

INSTRUCTIONS

1.STOP! Read the safety information above.

2.Turn ON/OFF switch, located on side of rear cover, to “OFF”.

3.Open lower door panel.

4.Turn off all electric power to the burner system.

5.Push in gas control knob slightly and turn clockwise to “OFF”.

6.Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Fol- low “B” in the safety information above. If you don't smell gas, go to the next step.

7.The pilot is located by the main burner and should not re- quire accessing for lighting.

8.Turn gas control knob counterclockwise to “PILOT”.

9.Push in gas control knob all the way and hold. Immedi- ately light the pilot by repeatedly depressing the piezo spark ignitor until a flame appears. Continue to hold for about one (1) minute after the pilot is lit. Release gas control knob and it will pop back. Pilot should remain lit. If it goes out, repeat steps 5 through 8.

•If gas control knob does not pop up when released, stop and immediately call your service technician or gas supplier.

•If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service techni- cian or gas supplier.

10.Turn gas control knob counterclockwise to “ON”.

11.Turn on all electric power to the burner system.

12.Turn the ON/OFF switch to ON position.

13.This valve is equipped with a HI/LO feature. Set burner system input as desired.

14.Close lower panel.

TO TURN OFF GAS

TO APPLIANCE

1.Turn ON/OFF switch, located on side of rear cover, to “OFF”.

2a. Open lower door panel.

2b. If Using Optional Hand-Held Remote: Set selector switch, located on side of rear cover, in the OFF position to pre- vent draining battery.

3.Turn off all electrical power to the appliance if service is to be performed.

4.Push in gas control knob slightly and turn clockwise to “OFF”.

5.Close lower panel.

Shutting Off Burners Only (pilot stays lit)

You may shut off the burners and keep the pilot lit by doing one of the following:

1.Turn gas control knob clockwise to the PILOT position.

2.Set selector switch in the OFF position.

Piezo

Gas Control Knob

 

Variable

 

Control Knob

Ignitor

 

 

 

 

 

 

 

 

 

 

OT

 

 

 

 

P

IL

 

 

 

 

 

 

ILO

 

 

 

 

P

T

 

 

 

 

F

O

HI

 

 

 

F

N

 

 

TH

 

O

 

 

 

 

 

 

 

 

 

LO

 

TP

 

 

 

 

 

TPTH

 

IN

OUT

 

 

 

Figure 59 - Control Valve

For..com

112126-01B

Page 25 Page 27
Image 26
Page 25 Page 27
Contents For Your Safety What to do if YOU Smell GAS OWNER’S Operation and Installation ManualFor Your Safety VH series StoveTable of Contents Safety InformationProduct Identification With stoveGlossary of Terms PRE-INSTALLATION Preparation Product FeaturesLocal Codes Stove Body Assembly PRE-INSTALLATION PreparationCast Iron Stove and DIRECT-VENT Burner System Assembly Locating Threaded Holes for Legs and Door Attachment Removing Screen Optional Installing DIRECT-VENT Burner System Into Stove BodyRemoving Front Surround Panel Amity ModelsInstalling Optional Blower Accessory Installing the Blower TOP ViewInstalling Rear Cover Blower Wiring Layout Thermostat Blower ShownGeneral Venting Location of Vent TerminationGeneral Venting Installation Planning Venting InstallationInstallation Precautions Installation for Horizontal Termination Installing Vent System in a ChaseVent Opening Requirements Venting with Three 90 Elbows Horizontal Termination ConfigurationsHorizontal Venting Venting with Two 90 ElbowsInstallation for Vertical Termination Flat Ceiling InstallationVenting with Two 90 Elbow Cathedral Ceiling InstallationVertical Termination Configurations Vertical Venting Configuration Using Two 90Elbows Venting with Two ElbowsVertical Venting High Altitude InstallationParts Lists for Venting Kits and Components Number DescriptionInstallation Items Needed Stove and DIRECT-VENT Burner System InstallationInstalling GAS Piping to STOVE/ Burner System Location Check GAS TypeChecking GAS Connections Connecting STOVE/BURNER System to GAS SupplyPressure Testing Gas Supply Piping System Installing Optional Wall Mount Switch GWMS2 Pressure Testing Burner System Gas ConnectionsInstalling Optional Wall Mounted Thermostat GWMT1 Installing Remote Receiver and 9-volt Alkaline BatteryInstalling Remote Receiver REMOVING/REPLACING Glass DoorInstalling LOGS, Lava Rock and Glowing Embers Installing Log No Installing Log NoLighting Instructions For Your Safety Read Before LightingOperating Stove with Burner System To Turn OFF GAS To ApplianceON/OFF Series Models Ghrcb and Cghrcb Manual LightingOptional HAND-HELD Remote Operation Thermostat Series Models Ghrctb and CghrctbInspecting Burners Operating Optional Blower AccessoryPilot Assembly Operating Optional GWMT1 Wall Mounted ThermostatPilot and Burners Cleaning and MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible Cause RemedyOrifice Gas leak. See Warning statement AboveReplacement Parts SpecificationsWiring Diagram Parts Under WarrantyIllustrated Parts Breakdown Models Sdvbnd SdvbpdParts List Models SDVBND, SdvbpdIndicates Color Suffix Designation Oxford Amity Stove Body Victor Hearth Stove BodyIndicates Color Suffix Designation Description QTYAccessories Technical ServiceService Hints Owners Registration Form For Com 112126-01B Warranty Information
Related manuals
Manual 42 pages 850 b

SDVBPD, SDVBND specifications

Desa SDVBPD and SDVBND are pioneering advancements in the domain of digital communication, designed to optimize services, enhance user engagement, and streamline processes in various sectors, including education, healthcare, and local governance. These systems have emerged as essential tools for efficient information dissemination and resource management.

One of the main features of Desa SDVBPD is its focus on decentralized communication. By utilizing local infrastructure, this system empowers communities to share information effectively and enhance interactions among residents. It enables local authorities to communicate directly with citizens, ensuring that pertinent information reaches the intended audience promptly. This feature is especially vital in emergency situations, where timely updates can significantly impact community safety and preparedness.

Similarly, SDVBND offers a robust platform for managing digital transactions and records. Its integration of blockchain technology ensures that all data processed is secure, immutable, and transparent. This characteristic is particularly beneficial for local government operations, as it minimizes the risk of fraud and enhances accountability in public service delivery. By leveraging this technology, Desa SDVBND can facilitate smooth and fast transactions between citizens and government entities, thereby transforming the way public services are accessed.

Another remarkable aspect of both systems is their accessibility. Designed with user-friendly interfaces, these platforms cater to individuals of varying technological proficiencies. Mobile compatibility allows users to engage with the systems from smartphones and tablets, making it easier to stay informed and involved. Furthermore, the platforms are multilingual, ensuring that communication is inclusive, reaching diverse populations within communities.

Interoperability stands out as a significant characteristic of Desa SDVBPD and SDVBND. Both systems are designed to seamlessly integrate with existing infrastructure and technologies, such as cloud computing and artificial intelligence. This adaptability enhances their functionality, enabling real-time data analysis and improved decision-making.

In conclusion, Desa SDVBPD and SDVBND represent a significant leap forward in community engagement and service delivery. By leveraging decentralized communication, blockchain technology, accessibility, and interoperability, these systems not only improve operational efficiency but also foster a sense of community empowerment. As they continue to evolve, they hold great promise for enabling smarter, more connected communities that can thrive in an increasingly digital world.
Top Page Image Contents