Desa VMH26TPB 14 Optional Mantel, Mantel Clearances for Built-In Installation, Able height

Page 10

® VMH26TPB

COMPACT CLASSIC HEARTH®

INSTALLATION

OPTIONAL MANTEL

Continued

INSTALLATION

FIREPLACE

9.

Place wood base next to wall at instal-

 

lation location.

10.

Attach wood base to floor with two 1 3/4"

WARNING: Do not allow non- combustible materials to cover any necessary openings like lou- vered slots.

WARNING: Never modify or cover the louvered slots on the front of the firebox.

WARNING: Use only noncom- bustible mortar or adhesives when overlapping the front fac- ing with noncombustible facing material.

Mantel Clearances for Built-In Installation

If placing mantel above built-in fireplace, you must meet minimum clearance between mantel shelf and top of fireplace opening.

NOTICE: Surface temperatures of adjacent walls and mantels be- come hot during operation. Walls and mantels above the firebox

Note: Refer to instructions provided with the mantel for assembly instructions. Refer to instructions below for system installa- tion. Refer to instructions on page 4 for firebox assembly. Blower accessory should be installed if it is being used (see Accesso- ries, page 26).

1.Unscrew four brass screws that attach top louver to fireplace. Remove louver from fireplace and set aside.

2.Place fireplace on wood base.

3.Place mantel around fireplace/base assembly.

4.Assemble brass trim kit. See Assem- bling Brass Trim, page 11.

5.Firmly snap brass trim kit on shoulder screws. Shoulder screws are located on fireplace cabinet (see Figure 13).

6.Align brass trim kit for flush fit around opening.

7.Use two 3" wood screws provided and attach fireplace base to wooden base (see Figure 13).

8.Remove brass trim kit and mantel. Be careful not to damage wall or mantel.

Mantel Shelf

 

black screws provided (see Figure 14).

 

If the floor is concrete use anchor method

 

(see Attaching Wood Base to Solid Floor,

 

page 14).

11. Install gas line. See Connecting To Gas

 

Supply, page 14.

12.

Check for leaks. See Checking Gas

 

Connections, page 16.

13.

Place mantel around fireplace. Be care-

 

ful not to damage wall or mantel.

14.

Place brass trim kit on the shoulder

 

screws located on the side and top of

 

the fireplace. Firmly snap the brass trim

 

over the shoulder screws on fireplace

 

(see Figure 13).

15.

Adjust assembly to remove any gaps.

 

Attach remaining two 3" wood screws

 

from hardware pack through openings

 

inside of fireplace sides into the man-

 

tel. The openings are located at top be-

 

hind the area for the brass louvers (see

 

Figure 14).

16.

Reinstall top brass louvers.

Shoulder Screws

may become hot to the touch. If installed properly, these tempera- tures meet the requirement of the national product standard. Fol- low all minimum clearances shown in this manual.

NOTICE: If your installation does not meet the minimum clearances shown, you must do one of the following:

• raise the mantel to an accept-

able height

Note:

10"

8"

All vertical

measurements

6"

are from top of

2 1/2"

fireplace

opening to bottom of mantel shelf. All measurements are in inches.

13"

16"

19"

21"

Side of

Firebox

Hole for 3" wood screw for attaching fireplace to mantel

Hole for 3" wood screw for attaching fireplace to wooden base

Assembled Brass Trim

• remove the mantel

Figure 13 - Attaching Brass Trim to Fireplace

1 3/4" Screw

Figure 12 - Minimum Mantel Clearances for Built-In Installation

Wood Base

Figure 14 - Attaching Wood Base to Floor

10

107030

Image 10
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASSafety Information Compact Classic Hearth FireplaceLocal Codes Product FeaturesUnpacking Product IdentificationAssembling Fireplace AssemblyInstalling Log Assembling HoodUnusually Tight Construction AIR for Combustion and VentilationProviding Adequate Ventilation Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating FireplaceBUILT-IN Fireplace Installation Locate fireplace where moving vehicle will not hit itRaise the mantel to an accept Mantel Clearances for Built-In InstallationOptional Mantel Able heightInstalling Blower Assembly Installing Blower Accessory GA3450TRemoving Upper Louver Assembly Assembling Brass Trim Brass trim shipped with mantelInstall the switch plate on the valve For Built-In Installation Extension CordAttaching Wood Base to Solid Floor Connecting to GAS SupplyThread inlet connection and the flexible gas line provided Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlValve should be accessible Pressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections Operating Fireplace For Your Safety Read Before LightingLighting Instructions Inspecting Burner Burner Flame Pattern Cleaning and MaintenanceCleaning Burner Injector Holder and Pilot AIR Inlet Hole CabinetTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Top Gas leak. See Warning statement atService Hints SpecificationsReplacement Parts Technical ServiceIllustrated Parts Breakdown VMH26TPBParts List KEY Description QTYAccessories 107030 Warranty Information