Desa VMH26TPB 14 Assembly, Assembling Fireplace, Installing Log, Assembling Hood

Page 4

® VMH26TPB

COMPACT CLASSIC HEARTH® FIREPLACE

ASSEMBLY

WARNING: Always have branch support and screen in place before operating fireplace. This prevents excessive tempera- tures on fireplace surfaces.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this fireplace may result in prop- erty damage or personal injury.

ASSEMBLING FIREPLACE

Tools Required:

Phillips screwdriver

5/16" hex wrench

slotted screwdriver

Installing Log

1.Lift screen up and pull out to remove.

2.Cut two plastic straps to remove the log from the firebox cavity.

Log

Shoulder

Burner Support with

 

 

Screw

Log Locator Tabs

Branch

Support

Screen

Figure 3 - Assembling Fireplace

3. An optional blower is available. See Ac-

cessories, page 26. Install optional

blower now. Follow installation in-

structions provided with blower.

4. Remove log packaging material and

discard packaging. Gently place log set

on burner support (see Figure 3). The

log should fit flat against top of burner

support and log locator tabs fit into the

slots under the log. Do not allow log to

Assembling Hood

1.Locate four black phillips sheet metal screws from the hardware packet.

2.Rotate hood as shown in Figure 4. Make sure hood tabs point toward fireplace.

3.Insert hood tabs between baffle and lou- vers (see Figure 4).

4.Gently rotate hood to upright position. Make sure hood tabs are behind lou- vers and hood is resting on firebox top (see Figure 4).

5.Align screw holes on hood with screw holes on firebox top.

6.Insert screws as shown in Figure 4. Tighten screws firmly.

contact flame. If flame contacts log,

soot will be created.

5. Reattach screen by placing the notches

in the screen frame over the shoulder

screws and pushing down.

 

 

Louver

Hood

Hood

Hood Tab

Tabs

 

 

Baffle

Sheet Metal

 

Screw

Firebox Top

Figure 4 - Assembling Hood

4

107030

Image 4
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASSafety Information Compact Classic Hearth FireplaceProduct Features UnpackingLocal Codes Product IdentificationAssembly Installing LogAssembling Fireplace Assembling HoodAIR for Combustion and Ventilation Providing Adequate VentilationUnusually Tight Construction Confined and Unconfined SpaceDetermining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation Installation ItemsCheck GAS Type Locating FireplaceBUILT-IN Fireplace Installation Locate fireplace where moving vehicle will not hit itMantel Clearances for Built-In Installation Optional MantelRaise the mantel to an accept Able heightInstalling Blower Accessory GA3450T Removing Upper Louver AssemblyInstalling Blower Assembly Assembling Brass Trim Brass trim shipped with mantelInstall the switch plate on the valve For Built-In Installation Extension CordAttaching Wood Base to Solid Floor Connecting to GAS SupplyThread inlet connection and the flexible gas line provided Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlValve should be accessible Pressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections Operating Fireplace For Your Safety Read Before LightingLighting Instructions Inspecting Burner Cleaning and Maintenance Cleaning Burner Injector Holder and Pilot AIR Inlet HoleBurner Flame Pattern CabinetTroubleshooting Observed Problem Possible Cause RemedyMaintenance, Top Gas leak. See Warning statement atSpecifications Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown VMH26TPBParts List KEY Description QTYAccessories 107030 Warranty Information