Desa VMH26TNC, VMH26TPC Installing Switch Plate to Valve Cover Shield, For Built-In Installation

Page 15

INSTALLATION

Continued

Valve Cover

Shield

Switch Screw

Plate

Figure 18 - Installing Switch Plate to

Valve Cover Shield

For Built-In Installation

WARNING: A licensed elec- trician must connect the wiring harness to electrical supply fol- lowing all local codes. Electri- cian must provide a clamp on the box cover to secure the wir- ing. Wiring should be routed through the bushing in the hole on the outer casing of heater.

lief clamp (not supplied) to secure incoming electrical supply.

2.Follow steps 2 through 6 in Installing Blower Assembly, page 13. Also remove black wire from middle switch terminal 2.

3.Remove black plastic strain relief and power cord from switch plate. The power cord supplied will not be used in built-in installations. Pop in the plastic snap bushing found in hardware kit into the hole left by supply cord/strain relief.

4.A licensed electrician must follow the wiring diagram to connect incoming electrical sup- ply to fan kit wiring harness (see Figure 19).

5.Plug power cord to the outlet receptacle (not provided) as shown in Figure 18. Wind the extra power cord and tie it up with the plastic wire strap (see Figure 20). Set the power cord bundle between the burner bracket and outer casing, away from the burner.

6.Reinstall valve cover shield.

7.Test to make sure the blower is working properly.

8.Reinstall upper louver assembly and hood if previously removed, (see Figure 15, page 13). Close lower louver door.

Follow instructions Removing Valve Cover Shield (page 13), then

1.Install a snap bushing found in hardware kit into one of the holes found on rear of valve cover shield. The other hole is for a strain re-

Blower Bracket

Wire Harness

Assembly

 

Fan Switch

(Auto/Off/On)

 

Thermostat

Switch (N.O.)

Auto

Blue

 

3

On

1

 

 

 

2

 

 

Off

 

Blower

Motor

 

 

Blue

Red

White

Green

Red

 

 

 

 

Black

White

Green

110/115 V.A.C.

 

 

 

Screw

 

 

Switch

Power

Cord

 

 

 

 

 

Outlet

Switch

3

Receptacle

1

 

 

2

 

Plate

 

 

Blue

Red

 

 

 

Plastic Wire

 

Strap

 

 

Valve

 

 

Cover

 

Wire

Shield

 

 

Clamp Connector

Harness

 

Box Cover

 

(not included)

 

Figure 19 - Wiring Diagram For Blower

Figure 20 - Installing Blower Bracket

Accessory Built-In Installation

Assembly

113111-01B

www.desatech.com

15

Image 15
Contents What to do if YOU Smell GAS Shown with Optional Cabinet Mantel/Hearth Base AccessoryTable of Contents Safety Information Product Identification Local CodesProduct Features AssemblyUnpacking Unusually Tight Construction AIR for Combustion VentilationProviding Adequate Ventilation Assembling HoodDetermining FRESH-AIR Flow for Fireplace Location Confined and Unconfined SpaceDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Installation Installation ItemsCheck GAS Type Locating Fireplace BUILT-IN Fireplace InstallationRough Opening for Installing Wall Mantel Clearances for Built-In Installation Optional Mantel InstallationRemoving Valve Cover Shield Installing Blower Accessory GA3450TRemoving Upper Louver Assembly Assembling Perimeter Trim Trim Shipped with MantelRemoving Valve Cover Shield Installing Blower AssemblyFor Built-In Installation Installing Switch Plate to Valve Cover ShieldConnecting to GAS Supply Attaching Wood Base to Solid FloorExtension Cord Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlPressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections For Your Safety Read Before Lighting Operating FireplaceLighting Instructions Shutting Off Fireplace Manual Lighting ProcedureTo Turn OFF GAS To Appliance Thermostat Control OperationPilot Flame Pattern Inspecting BurnerOperating Blower Burner Flame PatternAir Passageways Cleaning MaintenanceBurner Injector Holder and Pilot AIR Inlet Hole CabinetObserved Problem Possible Cause Remedy TroubleshootingSee Cleaning and Mainte Residues from manufacturing Statement above Gas leak. See WarningReplacement Parts SpecificationsService Hints Technical ServiceIllustrated Parts Breakdown Parts List Accessories Information Video Cleaning KIT GCKCorner Mantel with Full Hearth Base Cabinet Mantel and Full Hearth BaseWarranty Information Keep this WarrantyLimited Warranty VENT-FREE Compact Classic Hearth Fireplace