Desa VMH26TPC Attaching Wood Base to Solid Floor, Connecting to GAS Supply, Extension Cord

Page 16

INSTALLATION

Continued

Extension Cord

Use extension cord if needed. The cord must have a three-prong, grounding plug and a three-hole recep- tacle. Make sure cord is in good shape. It must be heavy enough to carry the current needed. An under- sized cord will cause a drop in line voltage. This will result in loss of power and overheating. Use a No. 16 AWG cord for lengths less than 50 feet.

ATTACHING WOOD BASE TO SOLID FLOOR

For attaching base to solid floors (concrete or masonry)

Note: Floor anchors and mounting screws are in hardware package. The hardware package is pro- vided with fireplace.

1.Drill holes at marked locations using 5/16" drill bit. For solid floors (concrete or ma- sonry), drill at least 1" deep.

2.Fold floor anchor as shown in Figure 21.

3.Insert floor anchor (wings first) into hole. Tap anchor flush to floor.

4.Insert mounting screws through base and into floor anchors.

5.Tighten screws until base is firmly fastened to floor.

Figure 21 - Folding Anchor

CONNECTING TO GAS SUPPLY

WARNING: This appliance re- quires a 45° male flare fitting 5/8"- 18 UNF (Unified National Fine Thread) inlet connection and the flexible gas line provided.

WARNING: A qualified ser- vice person must connect fire- place to gas supply. Follow all local codes.

CAUTION:Neverconnectpro- pane/LP fireplace directly to the propane/LPsupply.Thisfireplace requiresanexternalregulator(not supplied).Installtheexternalregu- lator between the fireplace and propane/LP supply.

WARNING: Never connect natural gas fireplace to private (non-utility) gas wells. This gas is commonlyknownaswellheadgas.

For propane/LP units, installer must supply an external regulator. The external regulator will re- duce incoming gas pressure. You must reduce in- coming gas pressure to between 11 and 14 inches of water. If you do not reduce incoming gas pres- sure, fireplace regulator damage could occur. In- stall external regulator with the vent pointing down as shown in Figure 22. Pointing the vent down protects it from freezing rain or sleet.

CAUTION: Use only new, black iron or steel pipe. Inter- nally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of 1/2" or greater diameter to allow proper gas volume to fireplace. If pipe is too small, undue loss of volume will occur.

Propane/LP

Supply Tank

External

Regulator

Vent

Pointing

Down

Figure 22- External Regulator with Vent

Pointing Down

16

www.desatech.com

113111-01B

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Shown with Optional Cabinet Mantel/Hearth Base Accessory What to do if YOU Smell GASTable of Contents Safety Information Local Codes Product IdentificationAssembly Product FeaturesUnpacking AIR for Combustion Ventilation Providing Adequate VentilationAssembling Hood Unusually Tight ConstructionConfined and Unconfined Space Determining FRESH-AIR Flow for Fireplace LocationDetermining if You Have a Confined or Unconfined Space Ventilation Air From Inside Building Ventilation AIRVentilation Air From Outdoors Installation Items InstallationCheck GAS Type BUILT-IN Fireplace Installation Locating FireplaceRough Opening for Installing Wall Optional Mantel Installation Mantel Clearances for Built-In InstallationInstalling Blower Accessory GA3450T Removing Upper Louver AssemblyAssembling Perimeter Trim Trim Shipped with Mantel Removing Valve Cover ShieldInstalling Blower Assembly Removing Valve Cover ShieldInstalling Switch Plate to Valve Cover Shield For Built-In InstallationAttaching Wood Base to Solid Floor Connecting to GAS SupplyExtension Cord Connecting Equipment Shutoff Valve to Heater Control Installation Items NeededPressure Testing Fireplace Gas Connections Pressure Testing Gas Supply Piping SystemChecking GAS Connections Operating Fireplace For Your Safety Read Before LightingLighting Instructions Manual Lighting Procedure To Turn OFF GAS To ApplianceThermostat Control Operation Shutting Off FireplaceInspecting Burner Operating BlowerBurner Flame Pattern Pilot Flame PatternCleaning Maintenance Burner Injector Holder and Pilot AIR Inlet HoleCabinet Air PassagewaysTroubleshooting Observed Problem Possible Cause RemedySee Cleaning and Mainte Residues from manufacturing Gas leak. See Warning Statement aboveSpecifications Service HintsTechnical Service Replacement PartsIllustrated Parts Breakdown Parts List Accessories Cleaning KIT GCK Corner Mantel with Full Hearth BaseCabinet Mantel and Full Hearth Base Information VideoKeep this Warranty Warranty InformationLimited Warranty VENT-FREE Compact Classic Hearth Fireplace
Top Page Image Contents